@@ -461,6 +461,286 @@ enum in6_addr_gen_mode {
/* Bridge section */
+/**
+ * DOC: Bridge enum definition
+ *
+ * Please *note* that the timer values in the following section are expected
+ * in clock_t format, which is seconds multiplied by USER_HZ (generally
+ * defined as 100).
+ *
+ * @IFLA_BR_FORWARD_DELAY
+ * The bridge forwarding delay is the time spent in LISTENING state
+ * (before moving to LEARNING) and in LEARNING state (before moving
+ * to FORWARDING). Only relevant if STP is enabled.
+ *
+ * The valid values are between (2 * USER_HZ) and (30 * USER_HZ).
+ * The default value is (15 * USER_HZ).
+ *
+ * @IFLA_BR_HELLO_TIME
+ * The time between hello packets sent by the bridge, when it is a root
+ * bridge or a designated bridge. Only relevant if STP is enabled.
+ *
+ * The valid values are between (1 * USER_HZ) and (10 * USER_HZ).
+ * The default value is (2 * USER_HZ).
+ *
+ * @IFLA_BR_MAX_AGE
+ * The hello packet timeout is the time until another bridge in the
+ * spanning tree is assumed to be dead, after reception of its last hello
+ * message. Only relevant if STP is enabled.
+ *
+ * The valid values are between (6 * USER_HZ) and (40 * USER_HZ).
+ * The default value is (20 * USER_HZ).
+ *
+ * @IFLA_BR_AGEING_TIME
+ * Configure the bridge's FDB entries aging time. It is the time a MAC
+ * address will be kept in the FDB after a packet has been received from
+ * that address. After this time has passed, entries are cleaned up.
+ * Allow values outside the 802.1 standard specification for special cases:
+ *
+ * * 0 - entry never ages (all permanent)
+ * * 1 - entry disappears (no persistence)
+ *
+ * The default value is (300 * USER_HZ).
+ *
+ * @IFLA_BR_STP_STATE
+ * Turn spanning tree protocol on (*IFLA_BR_STP_STATE* > 0) or off
+ * (*IFLA_BR_STP_STATE* == 0) for this bridge.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_PRIORITY
+ * Set this bridge's spanning tree priority, used during STP root bridge
+ * election.
+ *
+ * The valid values are between 0 and 65535.
+ *
+ * @IFLA_BR_VLAN_FILTERING
+ * Turn VLAN filtering on (*IFLA_BR_VLAN_FILTERING* > 0) or off
+ * (*IFLA_BR_VLAN_FILTERING* == 0). When disabled, the bridge will not
+ * consider the VLAN tag when handling packets.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_VLAN_PROTOCOL
+ * Set the protocol used for VLAN filtering.
+ *
+ * The valid values are 0x8100(802.1Q) or 0x88A8(802.1AD). The default value
+ * is 0x8100(802.1Q).
+ *
+ * @IFLA_BR_GROUP_FWD_MASK
+ * The group forwarding mask. This is the bitmask that is applied to
+ * decide whether to forward incoming frames destined to link-local
+ * addresses (of the form 01:80:C2:00:00:0X).
+ *
+ * The default value is 0, which means the bridge does not forward any
+ * link-local frames coming on this port.
+ *
+ * @IFLA_BR_ROOT_ID
+ * The bridge root id, read only.
+ *
+ * @IFLA_BR_BRIDGE_ID
+ * The bridge id, read only.
+ *
+ * @IFLA_BR_ROOT_PORT
+ * The bridge root port, read only.
+ *
+ * @IFLA_BR_ROOT_PATH_COST
+ * The bridge root path cost, read only.
+ *
+ * @IFLA_BR_TOPOLOGY_CHANGE
+ * The bridge topology change, read only.
+ *
+ * @IFLA_BR_TOPOLOGY_CHANGE_DETECTED
+ * The bridge topology change detected, read only.
+ *
+ * @IFLA_BR_HELLO_TIMER
+ * The bridge hello timer, read only.
+ *
+ * @IFLA_BR_TCN_TIMER
+ * The bridge tcn timer, read only.
+ *
+ * @IFLA_BR_TOPOLOGY_CHANGE_TIMER
+ * The bridge topology change timer, read only.
+ *
+ * @IFLA_BR_GC_TIMER
+ * The bridge gc timer, read only.
+ *
+ * @IFLA_BR_GROUP_ADDR
+ * Set the MAC address of the multicast group this bridge uses for STP.
+ * The address must be a link-local address in standard Ethernet MAC address
+ * format. It is an address of the form 01:80:C2:00:00:0X, with X in [0, 4..f].
+ *
+ * The default value is 0.
+ *
+ * @IFLA_BR_FDB_FLUSH
+ * Flush bridge's fdb dynamic entries.
+ *
+ * @IFLA_BR_MCAST_ROUTER
+ * Set bridge's multicast router if IGMP snooping is enabled.
+ * The valid values are:
+ *
+ * * 0 - disabled.
+ * * 1 - automatic (queried).
+ * * 2 - permanently enabled.
+ *
+ * The default value is 1.
+ *
+ * @IFLA_BR_MCAST_SNOOPING
+ * Turn multicast snooping on (*IFLA_BR_MCAST_SNOOPING* > 0) or off
+ * (*IFLA_BR_MCAST_SNOOPING* == 0).
+ *
+ * The default value is 1.
+ *
+ * @IFLA_BR_MCAST_QUERY_USE_IFADDR
+ * If enabled use the bridge's own IP address as source address for IGMP
+ * queries (*IFLA_BR_MCAST_QUERY_USE_IFADDR* > 0) or the default of 0.0.0.0
+ * (*IFLA_BR_MCAST_QUERY_USE_IFADDR* == 0).
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_MCAST_QUERIER
+ * Enable (*IFLA_BR_MULTICAST_QUERIER* > 0) or disable
+ * (*IFLA_BR_MULTICAST_QUERIER* == 0) IGMP querier, ie sending of multicast
+ * queries by the bridge.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_MCAST_HASH_ELASTICITY
+ * Set multicast database hash elasticity, It is the maximum chain length in
+ * the multicast hash table. This attribute is *deprecated* and the value
+ * is always 16.
+ *
+ * @IFLA_BR_MCAST_HASH_MAX
+ * Set maximum size of the multicast hash table
+ *
+ * The default value is 4096, the value must be a power of 2.
+ *
+ * @IFLA_BR_MCAST_LAST_MEMBER_CNT
+ * The Last Member Query Count is the number of Group-Specific Queries
+ * sent before the router assumes there are no local members. The Last
+ * Member Query Count is also the number of Group-and-Source-Specific
+ * Queries sent before the router assumes there are no listeners for a
+ * particular source.
+ *
+ * The default value is 2.
+ *
+ * @IFLA_BR_MCAST_STARTUP_QUERY_CNT
+ * The Startup Query Count is the number of Queries sent out on startup,
+ * separated by the Startup Query Interval.
+ *
+ * The default value is 2.
+ *
+ * @IFLA_BR_MCAST_LAST_MEMBER_INTVL
+ * The Last Member Query Interval is the Max Response Time inserted into
+ * Group-Specific Queries sent in response to Leave Group messages, and
+ * is also the amount of time between Group-Specific Query messages.
+ *
+ * The default value is (1 * USER_HZ).
+ *
+ * @IFLA_BR_MCAST_MEMBERSHIP_INTVL
+ * The interval after which the bridge will leave a group, if no membership
+ * reports for this group are received.
+ *
+ * The default value is (260 * USER_HZ).
+ *
+ * @IFLA_BR_MCAST_QUERIER_INTVL
+ * The interval between queries sent by other routers. if no queries are
+ * seen after this delay has passed, the bridge will start to send its own
+ * queries (as if *IFLA_BR_MCAST_QUERIER_INTVL* was enabled).
+ *
+ * The default value is (255 * USER_HZ).
+ *
+ * @IFLA_BR_MCAST_QUERY_INTVL
+ * The Query Interval is the interval between General Queries sent by
+ * the Querier.
+ *
+ * The default value is (125 * USER_HZ). The minimum value is (1 * USER_HZ).
+ *
+ * @IFLA_BR_MCAST_QUERY_RESPONSE_INTVL
+ * The Max Response Time used to calculate the Max Resp Code inserted
+ * into the periodic General Queries.
+ *
+ * The default value is (10 * USER_HZ).
+ *
+ * @IFLA_BR_MCAST_STARTUP_QUERY_INTVL
+ * The interval between queries in the startup phase.
+ *
+ * The default value is (125 * USER_HZ) / 4. The minimum value is (1 * USER_HZ).
+ *
+ * @IFLA_BR_NF_CALL_IPTABLES
+ * Enable (*NF_CALL_IPTABLES* > 0) or disable (*NF_CALL_IPTABLES* == 0)
+ * iptables hooks on the bridge.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_NF_CALL_IP6TABLES
+ * Enable (*NF_CALL_IP6TABLES* > 0) or disable (*NF_CALL_IP6TABLES* == 0)
+ * ip6tables hooks on the bridge.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_NF_CALL_ARPTABLES
+ * Enable (*NF_CALL_ARPTABLES* > 0) or disable (*NF_CALL_ARPTABLES* == 0)
+ * arptables hooks on the bridge.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_VLAN_DEFAULT_PVID
+ * VLAN ID applied to untagged and priority-tagged incoming packets.
+ *
+ * The default value is 1. Set to the special value 0 makes all ports of
+ * this bridge not have a PVID by default, which means that they will
+ * not accept VLAN-untagged traffic.
+ *
+ * @IFLA_BR_PAD
+ * Bridge attribute padding type for netlink message.
+ *
+ * @IFLA_BR_VLAN_STATS_ENABLED
+ * Enable (*IFLA_BR_VLAN_STATS_ENABLED* == 1) or disable
+ * (*IFLA_BR_VLAN_STATS_ENABLED* == 0) per-VLAN stats accounting.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_MCAST_STATS_ENABLED
+ * Enable (*IFLA_BR_MCAST_STATS_ENABLED* > 0) or disable
+ * (*IFLA_BR_MCAST_STATS_ENABLED* == 0) multicast (IGMP/MLD) stats
+ * accounting.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_MCAST_IGMP_VERSION
+ * Set the IGMP version.
+ *
+ * The valid values are 2 and 3. The default value is 2.
+ *
+ * @IFLA_BR_MCAST_MLD_VERSION
+ * Set the MLD version.
+ *
+ * The valid values are 1 and 2. The default value is 1.
+ *
+ * @IFLA_BR_VLAN_STATS_PER_PORT
+ * Enable (*IFLA_BR_VLAN_STATS_PER_PORT* == 1) or disable
+ * (*IFLA_BR_VLAN_STATS_PER_PORT* == 0) per-VLAN per-port stats accounting.
+ * Can be changed only when there are no port VLANs configured.
+ *
+ * The default value is 0 (disabled).
+ *
+ * @IFLA_BR_MULTI_BOOLOPT
+ * The multi_boolopt is used to control new boolean options to avoid adding
+ * new netlink attributes. You can look at ``enum br_boolopt_id`` for those
+ * options.
+ *
+ * @IFLA_BR_MCAST_QUERIER_STATE
+ * Bridge mcast querier states, read only.
+ *
+ * @IFLA_BR_FDB_N_LEARNED
+ * The number of dynamically learned FDB entries for the current bridge,
+ * read only.
+ *
+ * @IFLA_BR_FDB_MAX_LEARNED
+ * Set the number of max dynamically learned FDB entries for the current
+ * bridge.
+ */
enum {
IFLA_BR_UNSPEC,
IFLA_BR_FORWARD_DELAY,
Add document for IFLA_BR enum so we can use it in Documentation/networking/bridge.rst. Signed-off-by: Hangbin Liu <liuhangbin@gmail.com> --- include/uapi/linux/if_link.h | 280 +++++++++++++++++++++++++++++++++++ 1 file changed, 280 insertions(+)