@@ -212,3 +212,21 @@ int wx_set_link_ksettings(struct net_device *netdev,
return phylink_ethtool_ksettings_set(wx->phylink, cmd);
}
EXPORT_SYMBOL(wx_set_link_ksettings);
+
+void wx_get_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct wx *wx = netdev_priv(netdev);
+
+ phylink_ethtool_get_pauseparam(wx->phylink, pause);
+}
+EXPORT_SYMBOL(wx_get_pauseparam);
+
+int wx_set_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause)
+{
+ struct wx *wx = netdev_priv(netdev);
+
+ return phylink_ethtool_set_pauseparam(wx->phylink, pause);
+}
+EXPORT_SYMBOL(wx_set_pauseparam);
@@ -18,4 +18,8 @@ int wx_get_link_ksettings(struct net_device *netdev,
struct ethtool_link_ksettings *cmd);
int wx_set_link_ksettings(struct net_device *netdev,
const struct ethtool_link_ksettings *cmd);
+void wx_get_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause);
+int wx_set_pauseparam(struct net_device *netdev,
+ struct ethtool_pauseparam *pause);
#endif /* _WX_ETHTOOL_H_ */
@@ -1158,6 +1158,81 @@ static void wx_set_rxpba(struct wx *wx)
wr32(wx, WX_TDM_PB_THRE(0), txpbthresh);
}
+#define WX_ETH_FRAMING 20
+
+/**
+ * wx_hpbthresh - calculate high water mark for flow control
+ *
+ * @wx: board private structure to calculate for
+ **/
+static int wx_hpbthresh(struct wx *wx)
+{
+ struct net_device *dev = wx->netdev;
+ int link, tc, kb, marker;
+ u32 dv_id, rx_pba;
+
+ /* Calculate max LAN frame size */
+ link = dev->mtu + ETH_HLEN + ETH_FCS_LEN + WX_ETH_FRAMING;
+ tc = link;
+
+ /* Calculate delay value for device */
+ dv_id = WX_DV(link, tc);
+
+ /* Delay value is calculated in bit times convert to KB */
+ kb = WX_BT2KB(dv_id);
+ rx_pba = rd32(wx, WX_RDB_PB_SZ(0)) >> WX_RDB_PB_SZ_SHIFT;
+
+ marker = rx_pba - kb;
+
+ /* It is possible that the packet buffer is not large enough
+ * to provide required headroom. In this case throw an error
+ * to user and a do the best we can.
+ */
+ if (marker < 0) {
+ dev_warn(&wx->pdev->dev,
+ "Packet Buffer can not provide enough headroom to support flow control. Decrease MTU or number of traffic classes\n");
+ marker = tc + 1;
+ }
+
+ return marker;
+}
+
+/**
+ * wx_lpbthresh - calculate low water mark for flow control
+ *
+ * @wx: board private structure to calculate for
+ **/
+static int wx_lpbthresh(struct wx *wx)
+{
+ struct net_device *dev = wx->netdev;
+ u32 dv_id;
+ int tc;
+
+ /* Calculate max LAN frame size */
+ tc = dev->mtu + ETH_HLEN + ETH_FCS_LEN;
+
+ /* Calculate delay value for device */
+ dv_id = WX_LOW_DV(tc);
+
+ /* Delay value is calculated in bit times convert to KB */
+ return WX_BT2KB(dv_id);
+}
+
+/**
+ * wx_pbthresh_setup - calculate and setup high low water marks
+ *
+ * @wx: board private structure to calculate for
+ **/
+static void wx_pbthresh_setup(struct wx *wx)
+{
+ wx->fc.high_water = wx_hpbthresh(wx);
+ wx->fc.low_water = wx_lpbthresh(wx);
+
+ /* Low water marks must not be larger than high water marks */
+ if (wx->fc.low_water > wx->fc.high_water)
+ wx->fc.low_water = 0;
+}
+
static void wx_configure_port(struct wx *wx)
{
u32 value, i;
@@ -1584,6 +1659,7 @@ static void wx_configure_isb(struct wx *wx)
void wx_configure(struct wx *wx)
{
wx_set_rxpba(wx);
+ wx_pbthresh_setup(wx);
wx_configure_port(wx);
wx_set_rx_mode(wx->netdev);
@@ -2003,6 +2079,102 @@ int wx_vlan_rx_kill_vid(struct net_device *netdev, __be16 proto, u16 vid)
}
EXPORT_SYMBOL(wx_vlan_rx_kill_vid);
+static void wx_enable_rx_drop(struct wx *wx, struct wx_ring *ring)
+{
+ u16 reg_idx = ring->reg_idx;
+ u32 srrctl;
+
+ srrctl = rd32(wx, WX_PX_RR_CFG(reg_idx));
+ srrctl |= WX_PX_RR_CFG_DROP_EN;
+
+ wr32(wx, WX_PX_RR_CFG(reg_idx), srrctl);
+}
+
+static void wx_disable_rx_drop(struct wx *wx, struct wx_ring *ring)
+{
+ u16 reg_idx = ring->reg_idx;
+ u32 srrctl;
+
+ srrctl = rd32(wx, WX_PX_RR_CFG(reg_idx));
+ srrctl &= ~WX_PX_RR_CFG_DROP_EN;
+
+ wr32(wx, WX_PX_RR_CFG(reg_idx), srrctl);
+}
+
+int wx_fc_enable(struct wx *wx, bool tx_pause, bool rx_pause)
+{
+ u16 pause_time = WX_DEFAULT_FCPAUSE;
+ u32 mflcn_reg, fccfg_reg, reg;
+ u32 fcrtl, fcrth;
+ int i;
+
+ /* Low water mark of zero causes XOFF floods */
+ if (tx_pause && wx->fc.high_water) {
+ if (!wx->fc.low_water || wx->fc.low_water >= wx->fc.high_water) {
+ wx_err(wx, "Invalid water mark configuration\n");
+ return -EINVAL;
+ }
+ }
+
+ /* Disable any previous flow control settings */
+ mflcn_reg = rd32(wx, WX_MAC_RX_FLOW_CTRL);
+ mflcn_reg &= ~WX_MAC_RX_FLOW_CTRL_RFE;
+
+ fccfg_reg = rd32(wx, WX_RDB_RFCC);
+ fccfg_reg &= ~WX_RDB_RFCC_RFCE_802_3X;
+
+ if (rx_pause)
+ mflcn_reg |= WX_MAC_RX_FLOW_CTRL_RFE;
+ if (tx_pause)
+ fccfg_reg |= WX_RDB_RFCC_RFCE_802_3X;
+
+ /* Set 802.3x based flow control settings. */
+ wr32(wx, WX_MAC_RX_FLOW_CTRL, mflcn_reg);
+ wr32(wx, WX_RDB_RFCC, fccfg_reg);
+
+ /* Set up and enable Rx high/low water mark thresholds, enable XON. */
+ if (tx_pause && wx->fc.high_water) {
+ fcrtl = (wx->fc.low_water << 10) | WX_RDB_RFCL_XONE;
+ wr32(wx, WX_RDB_RFCL, fcrtl);
+ fcrth = (wx->fc.high_water << 10) | WX_RDB_RFCH_XOFFE;
+ } else {
+ wr32(wx, WX_RDB_RFCL, 0);
+ /* In order to prevent Tx hangs when the internal Tx
+ * switch is enabled we must set the high water mark
+ * to the Rx packet buffer size - 24KB. This allows
+ * the Tx switch to function even under heavy Rx
+ * workloads.
+ */
+ fcrth = rd32(wx, WX_RDB_PB_SZ(0)) - 24576;
+ }
+
+ wr32(wx, WX_RDB_RFCH, fcrth);
+
+ /* Configure pause time */
+ reg = pause_time * 0x00010001;
+ wr32(wx, WX_RDB_RFCV, reg);
+
+ /* Configure flow control refresh threshold value */
+ wr32(wx, WX_RDB_RFCRT, pause_time / 2);
+
+ /* We should set the drop enable bit if:
+ * Number of Rx queues > 1 and flow control is disabled
+ *
+ * This allows us to avoid head of line blocking for security
+ * and performance reasons.
+ */
+ if (wx->num_rx_queues > 1 && !tx_pause) {
+ for (i = 0; i < wx->num_rx_queues; i++)
+ wx_enable_rx_drop(wx, wx->rx_ring[i]);
+ } else {
+ for (i = 0; i < wx->num_rx_queues; i++)
+ wx_disable_rx_drop(wx, wx->rx_ring[i]);
+ }
+
+ return 0;
+}
+EXPORT_SYMBOL(wx_fc_enable);
+
/**
* wx_update_stats - Update the board statistics counters.
* @wx: board private structure
@@ -41,6 +41,7 @@ int wx_get_pcie_msix_counts(struct wx *wx, u16 *msix_count, u16 max_msix_count);
int wx_sw_init(struct wx *wx);
int wx_vlan_rx_add_vid(struct net_device *netdev, __be16 proto, u16 vid);
int wx_vlan_rx_kill_vid(struct net_device *netdev, __be16 proto, u16 vid);
+int wx_fc_enable(struct wx *wx, bool tx_pause, bool rx_pause);
void wx_update_stats(struct wx *wx);
void wx_clear_hw_cntrs(struct wx *wx);
@@ -131,6 +131,15 @@
#define WX_RDB_PFCMACDAH 0x19214
#define WX_RDB_LXOFFTXC 0x19218
#define WX_RDB_LXONTXC 0x1921C
+/* Flow Control Registers */
+#define WX_RDB_RFCV 0x19200
+#define WX_RDB_RFCL 0x19220
+#define WX_RDB_RFCL_XONE BIT(31)
+#define WX_RDB_RFCH 0x19260
+#define WX_RDB_RFCH_XOFFE BIT(31)
+#define WX_RDB_RFCRT 0x192A0
+#define WX_RDB_RFCC 0x192A4
+#define WX_RDB_RFCC_RFCE_802_3X BIT(3)
/* ring assignment */
#define WX_RDB_PL_CFG(_i) (0x19300 + ((_i) * 4))
#define WX_RDB_PL_CFG_L4HDR BIT(1)
@@ -331,6 +340,7 @@ enum WX_MSCA_CMD_value {
#define WX_PX_MPRC(_i) (0x01020 + ((_i) * 0x40))
/* PX_RR_CFG bit definitions */
#define WX_PX_RR_CFG_VLAN BIT(31)
+#define WX_PX_RR_CFG_DROP_EN BIT(30)
#define WX_PX_RR_CFG_SPLIT_MODE BIT(26)
#define WX_PX_RR_CFG_RR_THER_SHIFT 16
#define WX_PX_RR_CFG_RR_HDR_SZ GENMASK(15, 12)
@@ -368,6 +378,38 @@ enum WX_MSCA_CMD_value {
#define WX_MAC_STATE_MODIFIED 0x2
#define WX_MAC_STATE_IN_USE 0x4
+/* BitTimes (BT) conversion */
+#define WX_BT2KB(BT) (((BT) + (8 * 1024 - 1)) / (8 * 1024))
+#define WX_B2BT(BT) ((BT) * 8)
+
+/* Calculate Delay to respond to PFC */
+#define WX_PFC_D 672
+/* Calculate Cable Delay */
+#define WX_CABLE_DC 5556 /* Delay Copper */
+/* Calculate Delay incurred from higher layer */
+#define WX_HD 6144
+
+/* Calculate Interface Delay */
+#define WX_PHY_D 12800
+#define WX_MAC_D 4096
+#define WX_XAUI_D (2 * 1024)
+#define WX_ID (WX_MAC_D + WX_XAUI_D + WX_PHY_D)
+/* Calculate PCI Bus delay for low thresholds */
+#define WX_PCI_DELAY 10000
+
+/* Calculate delay value in bit times */
+#define WX_DV(_max_frame_link, _max_frame_tc) \
+ ((36 * (WX_B2BT(_max_frame_link) + WX_PFC_D + \
+ (2 * WX_CABLE_DC) + (2 * WX_ID) + WX_HD) / 25 + 1) + \
+ 2 * WX_B2BT(_max_frame_tc))
+
+/* Calculate low threshold delay values */
+#define WX_LOW_DV(_max_frame_tc) \
+ (2 * (2 * WX_B2BT(_max_frame_tc) + (36 * WX_PCI_DELAY / 25) + 1))
+
+/* flow control */
+#define WX_DEFAULT_FCPAUSE 0xFFFF
+
#define WX_MAX_RXD 8192
#define WX_MAX_TXD 8192
@@ -881,6 +923,11 @@ enum wx_isb_idx {
WX_ISB_MAX
};
+struct wx_fc_info {
+ u32 high_water; /* Flow Ctrl High-water */
+ u32 low_water; /* Flow Ctrl Low-water */
+};
+
/* Statistics counters collected by the MAC */
struct wx_hw_stats {
u64 gprc;
@@ -921,6 +968,7 @@ struct wx {
enum sp_media_type media_type;
struct wx_eeprom_info eeprom;
struct wx_addr_filter_info addr_ctrl;
+ struct wx_fc_info fc;
struct wx_mac_addr *mac_table;
u16 device_id;
u16 vendor_id;
@@ -54,6 +54,8 @@ static const struct ethtool_ops ngbe_ethtool_ops = {
.get_ethtool_stats = wx_get_ethtool_stats,
.get_eth_mac_stats = wx_get_mac_stats,
.get_pause_stats = wx_get_pause_stats,
+ .get_pauseparam = wx_get_pauseparam,
+ .set_pauseparam = wx_set_pauseparam,
};
void ngbe_set_ethtool_ops(struct net_device *netdev)
@@ -76,6 +76,8 @@ static void ngbe_mac_link_up(struct phylink_config *config,
struct wx *wx = phylink_to_wx(config);
u32 lan_speed, reg;
+ wx_fc_enable(wx, tx_pause, rx_pause);
+
switch (speed) {
case SPEED_10:
lan_speed = 0;
@@ -21,6 +21,8 @@ static const struct ethtool_ops txgbe_ethtool_ops = {
.get_ethtool_stats = wx_get_ethtool_stats,
.get_eth_mac_stats = wx_get_mac_stats,
.get_pause_stats = wx_get_pause_stats,
+ .get_pauseparam = wx_get_pauseparam,
+ .set_pauseparam = wx_set_pauseparam,
};
void txgbe_set_ethtool_ops(struct net_device *netdev)
@@ -190,6 +190,8 @@ static void txgbe_mac_link_up(struct phylink_config *config,
struct wx *wx = phylink_to_wx(config);
u32 txcfg, wdg;
+ wx_fc_enable(wx, tx_pause, rx_pause);
+
txcfg = rd32(wx, WX_MAC_TX_CFG);
txcfg &= ~WX_MAC_TX_CFG_SPEED_MASK;
Add support to set pause params with ethtool -A and get pause params with ethtool -a, for ethernet driver txgbe and ngbe. Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com> --- .../net/ethernet/wangxun/libwx/wx_ethtool.c | 18 ++ .../net/ethernet/wangxun/libwx/wx_ethtool.h | 4 + drivers/net/ethernet/wangxun/libwx/wx_hw.c | 172 ++++++++++++++++++ drivers/net/ethernet/wangxun/libwx/wx_hw.h | 1 + drivers/net/ethernet/wangxun/libwx/wx_type.h | 48 +++++ .../net/ethernet/wangxun/ngbe/ngbe_ethtool.c | 2 + drivers/net/ethernet/wangxun/ngbe/ngbe_mdio.c | 2 + .../ethernet/wangxun/txgbe/txgbe_ethtool.c | 2 + .../net/ethernet/wangxun/txgbe/txgbe_phy.c | 2 + 9 files changed, 251 insertions(+)