| Message ID | 20231227044347.107291-6-arinc.unal@arinc9.com (mailing list archive) |
|---|---|
| State | Deferred |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | MT7530 DSA Subdriver Improvements Act I | expand |
On Wed, Dec 27, 2023 at 07:43:45AM +0300, Arınç ÜNAL wrote: > There're two code paths for setting up port 5: > > mt7530_setup() > -> mt7530_setup_port5() > > mt753x_phylink_mac_config() > -> mt753x_mac_config() > -> mt7530_mac_config() > -> mt7530_setup_port5() > > Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5 > is used as a CPU, DSA, or user port, mt7530_setup_port5() from > mt753x_phylink_mac_config() won't run. That is because priv->p5_interface > set on mt7530_setup_port5() will match state->interface on > mt753x_phylink_mac_config() which will stop running mt7530_setup_port5() > again. > > Therefore, mt7530_setup_port5() will never run from > mt753x_phylink_mac_config(). > > Address this by not running mt7530_setup_port5() from mt7530_setup() if > port 5 is used as a CPU, DSA, or user port. This driver isn't in the > dsa_switches_apply_workarounds[] array so phylink will always be present. > > To keep the cases where port 5 isn't controlled by phylink working as > before, preserve the mt7530_setup_port5() call from mt7530_setup(). > > Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when > "priv" is allocated. > > Move setting the interface to a more specific location. It's supposed to be > overwritten if PHY muxing is detected. > > Improve the comment which explains the process. > > Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> > --- Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index 558784f830c2..bf6c59ecc489 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -2308,16 +2308,15 @@ mt7530_setup(struct dsa_switch *ds) return ret; /* Setup port 5 */ - priv->p5_intf_sel = P5_DISABLED; - interface = PHY_INTERFACE_MODE_NA; - if (!dsa_is_unused_port(ds, 5)) { priv->p5_intf_sel = P5_INTF_SEL_GMAC5; - ret = of_get_phy_mode(dsa_to_port(ds, 5)->dn, &interface); - if (ret && ret != -ENODEV) - return ret; } else { - /* Scan the ethernet nodes. look for GMAC1, lookup used phy */ + /* Scan the ethernet nodes. Look for GMAC1, lookup the used PHY. + * Set priv->p5_intf_sel to the appropriate value if PHY muxing + * is detected. + */ + interface = PHY_INTERFACE_MODE_NA; + for_each_child_of_node(dn, mac_np) { if (!of_device_is_compatible(mac_np, "mediatek,eth-mac")) @@ -2348,6 +2347,8 @@ mt7530_setup(struct dsa_switch *ds) of_node_put(phy_node); break; } + + mt7530_setup_port5(ds, interface); } #ifdef CONFIG_GPIOLIB @@ -2358,8 +2359,6 @@ mt7530_setup(struct dsa_switch *ds) } #endif /* CONFIG_GPIOLIB */ - mt7530_setup_port5(ds, interface); - /* Flush the FDB table */ ret = mt7530_fdb_cmd(priv, MT7530_FDB_FLUSH, NULL); if (ret < 0)
There're two code paths for setting up port 5: mt7530_setup() -> mt7530_setup_port5() mt753x_phylink_mac_config() -> mt753x_mac_config() -> mt7530_mac_config() -> mt7530_setup_port5() Currently mt7530_setup_port5() from mt7530_setup() always runs. If port 5 is used as a CPU, DSA, or user port, mt7530_setup_port5() from mt753x_phylink_mac_config() won't run. That is because priv->p5_interface set on mt7530_setup_port5() will match state->interface on mt753x_phylink_mac_config() which will stop running mt7530_setup_port5() again. Therefore, mt7530_setup_port5() will never run from mt753x_phylink_mac_config(). Address this by not running mt7530_setup_port5() from mt7530_setup() if port 5 is used as a CPU, DSA, or user port. This driver isn't in the dsa_switches_apply_workarounds[] array so phylink will always be present. To keep the cases where port 5 isn't controlled by phylink working as before, preserve the mt7530_setup_port5() call from mt7530_setup(). Do not set priv->p5_intf_sel to P5_DISABLED. It is already set to that when "priv" is allocated. Move setting the interface to a more specific location. It's supposed to be overwritten if PHY muxing is detected. Improve the comment which explains the process. Signed-off-by: Arınç ÜNAL <arinc.unal@arinc9.com> --- drivers/net/dsa/mt7530.c | 17 ++++++++--------- 1 file changed, 8 insertions(+), 9 deletions(-)