@@ -99,6 +99,7 @@ config USB_RTL8150
config USB_RTL8152
tristate "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
select MII
+ select PHYLIB
select CRC32
select CRYPTO
select CRYPTO_HASH
@@ -10,6 +10,7 @@
#include <linux/etherdevice.h>
#include <linux/mii.h>
#include <linux/ethtool.h>
+#include <linux/phy.h>
#include <linux/usb.h>
#include <linux/crc32.h>
#include <linux/if_vlan.h>
@@ -8924,23 +8925,22 @@ static void rtl8152_get_strings(struct net_device *dev, u32 stringset, u8 *data)
static int r8152_get_eee(struct r8152 *tp, struct ethtool_keee *eee)
{
- u32 lp, adv, supported = 0;
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(common);
u16 val;
val = r8152_mmd_read(tp, MDIO_MMD_PCS, MDIO_PCS_EEE_ABLE);
- supported = mmd_eee_cap_to_ethtool_sup_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->supported, val);
val = r8152_mmd_read(tp, MDIO_MMD_AN, MDIO_AN_EEE_ADV);
- adv = mmd_eee_adv_to_ethtool_adv_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->advertised, val);
val = r8152_mmd_read(tp, MDIO_MMD_AN, MDIO_AN_EEE_LPABLE);
- lp = mmd_eee_adv_to_ethtool_adv_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->lp_advertised, val);
eee->eee_enabled = tp->eee_en;
- eee->eee_active = !!(supported & adv & lp);
- eee->supported_u32 = supported;
- eee->advertised_u32 = tp->eee_adv;
- eee->lp_advertised_u32 = lp;
+
+ linkmode_and(common, eee->advertised, eee->lp_advertised);
+ eee->eee_active = phy_check_valid(tp->speed, tp->duplex, common);
return 0;
}
@@ -8959,23 +8959,22 @@ static int r8152_set_eee(struct r8152 *tp, struct ethtool_keee *eee)
static int r8153_get_eee(struct r8152 *tp, struct ethtool_keee *eee)
{
- u32 lp, adv, supported = 0;
+ __ETHTOOL_DECLARE_LINK_MODE_MASK(common);
u16 val;
val = ocp_reg_read(tp, OCP_EEE_ABLE);
- supported = mmd_eee_cap_to_ethtool_sup_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->supported, val);
val = ocp_reg_read(tp, OCP_EEE_ADV);
- adv = mmd_eee_adv_to_ethtool_adv_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->advertised, val);
val = ocp_reg_read(tp, OCP_EEE_LPABLE);
- lp = mmd_eee_adv_to_ethtool_adv_t(val);
+ mii_eee_cap1_mod_linkmode_t(eee->lp_advertised, val);
eee->eee_enabled = tp->eee_en;
- eee->eee_active = !!(supported & adv & lp);
- eee->supported_u32 = supported;
- eee->advertised_u32 = tp->eee_adv;
- eee->lp_advertised_u32 = lp;
+
+ linkmode_and(common, eee->advertised, eee->lp_advertised);
+ eee->eee_active = phy_check_valid(tp->speed, tp->duplex, common);
return 0;
}
Make use of the existing linkmode helpers for converting PHY EEE register values into links modes, now that ethtool_keee uses link modes, rather than u32 values. Rework determining if EEE is active to make is similar as to how phylib decides, and make use of a phylib helper to validate if EEE is valid in for the current link mode. This then requires that PHYLIB is selected. Signed-off-by: Andrew Lunn <andrew@lunn.ch> --- drivers/net/usb/Kconfig | 1 + drivers/net/usb/r8152.c | 31 +++++++++++++++---------------- 2 files changed, 16 insertions(+), 16 deletions(-)