@@ -173,7 +173,7 @@ Director rule is added from ethtool (Sideband filter), ATR is turned off by the
driver. To re-enable ATR, the sideband can be disabled with the ethtool -K
option. For example::
- ethtool –K [adapter] ntuple [off|on]
+ ethtool -K [adapter] ntuple [off|on]
If sideband is re-enabled after ATR is re-enabled, ATR remains enabled until a
TCP-IP flow is added. When all TCP-IP sideband rules are deleted, ATR is
@@ -466,7 +466,7 @@ network. PTP support varies among Intel devices that support this driver. Use
"ethtool -T <netdev name>" to get a definitive list of PTP capabilities
supported by the device.
-IEEE 802.1ad (QinQ) Support
+IEEE 802.1ad (QinQ) Support
---------------------------
The IEEE 802.1ad standard, informally known as QinQ, allows for multiple VLAN
IDs within a single Ethernet frame. VLAN IDs are sometimes referred to as
@@ -523,8 +523,8 @@ of a port's bandwidth (should it be available). The sum of all the values for
Maximum Bandwidth is not restricted, because no more than 100% of a port's
bandwidth can ever be used.
-NOTE: X710/XXV710 devices fail to enable Max VFs (64) when Multiple Functions
-per Port (MFP) and SR-IOV are enabled. An error from i40e is logged that says
+NOTE: X710/XXV710 devices fail to enable Max VFs (64) when Multiple Functions
+per Port (MFP) and SR-IOV are enabled. An error from i40e is logged that says
"add vsi failed for VF N, aq_err 16". To workaround the issue, enable less than
64 virtual functions (VFs).
@@ -680,7 +680,7 @@ queues: for each tc, <num queues>@<offset> (e.g. queues 16@0 16@16 assigns
16 queues to tc0 at offset 0 and 16 queues to tc1 at offset 16. Max total
number of queues for all tcs is 64 or number of cores, whichever is lower.)
-hw 1 mode channel: ‘channel’ with ‘hw’ set to 1 is a new new hardware
+hw 1 mode channel: 'channel' with 'hw' set to 1 is a new new hardware
offload mode in mqprio that makes full use of the mqprio options, the
TCs, the queue configurations, and the QoS parameters.
@@ -688,7 +688,7 @@ shaper bw_rlimit: for each tc, sets minimum and maximum bandwidth rates.
Totals must be equal or less than port speed.
For example: min_rate 1Gbit 3Gbit: Verify bandwidth limit using network
-monitoring tools such as ifstat or sar –n DEV [interval] [number of samples]
+monitoring tools such as ifstat or sar -n DEV [interval] [number of samples]
2. Enable HW TC offload on interface::
@@ -113,7 +113,7 @@ which the AVF is associated. The following are base mode features:
- AVF device ID
- HW mailbox is used for VF to PF communications (including on Windows)
-IEEE 802.1ad (QinQ) Support
+IEEE 802.1ad (QinQ) Support
---------------------------
The IEEE 802.1ad standard, informally known as QinQ, allows for multiple VLAN
IDs within a single Ethernet frame. VLAN IDs are sometimes referred to as
@@ -171,7 +171,7 @@ queues: for each tc, <num queues>@<offset> (e.g. queues 16@0 16@16 assigns
16 queues to tc0 at offset 0 and 16 queues to tc1 at offset 16. Max total
number of queues for all tcs is 64 or number of cores, whichever is lower.)
-hw 1 mode channel: ‘channel’ with ‘hw’ set to 1 is a new new hardware
+hw 1 mode channel: 'channel' with 'hw' set to 1 is a new new hardware
offload mode in mqprio that makes full use of the mqprio options, the
TCs, the queue configurations, and the QoS parameters.
@@ -179,7 +179,7 @@ shaper bw_rlimit: for each tc, sets minimum and maximum bandwidth rates.
Totals must be equal or less than port speed.
For example: min_rate 1Gbit 3Gbit: Verify bandwidth limit using network
-monitoring tools such as ifstat or sar –n DEV [interval] [number of samples]
+monitoring tools such as ifstat or sar -n DEV [interval] [number of samples]
NOTE:
Setting up channels via ethtool (ethtool -L) is not supported when the
@@ -62,14 +62,14 @@ actual firmware files in application-named subdirectories in
$ tree /lib/firmware/netronome/
/lib/firmware/netronome/
├── bpf
- │ ├── nic_AMDA0081-0001_1x40.nffw
- │ └── nic_AMDA0081-0001_4x10.nffw
+ │ ├── nic_AMDA0081-0001_1x40.nffw
+ │ └── nic_AMDA0081-0001_4x10.nffw
├── flower
- │ ├── nic_AMDA0081-0001_1x40.nffw
- │ └── nic_AMDA0081-0001_4x10.nffw
+ │ ├── nic_AMDA0081-0001_1x40.nffw
+ │ └── nic_AMDA0081-0001_4x10.nffw
├── nic
- │ ├── nic_AMDA0081-0001_1x40.nffw
- │ └── nic_AMDA0081-0001_4x10.nffw
+ │ ├── nic_AMDA0081-0001_1x40.nffw
+ │ └── nic_AMDA0081-0001_4x10.nffw
├── nic_AMDA0081-0001_1x40.nffw -> bpf/nic_AMDA0081-0001_1x40.nffw
└── nic_AMDA0081-0001_4x10.nffw -> bpf/nic_AMDA0081-0001_4x10.nffw
While UTF-8 characters can be used at the Linux documentation, the best is to use them only when ASCII doesn't offer a good replacement. So, replace the occurences of the following UTF-8 characters: - U+00a0 (' '): NO-BREAK SPACE - U+2013 ('–'): EN DASH - U+2018 ('‘'): LEFT SINGLE QUOTATION MARK - U+2019 ('’'): RIGHT SINGLE QUOTATION MARK Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> --- .../device_drivers/ethernet/intel/i40e.rst | 12 ++++++------ .../device_drivers/ethernet/intel/iavf.rst | 6 +++--- .../device_drivers/ethernet/netronome/nfp.rst | 12 ++++++------ 3 files changed, 15 insertions(+), 15 deletions(-)