diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index 54874555c921..63ba7f51087e 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -284,6 +284,11 @@ config NCN26000_PHY
 	  Currently supports the NCN26000 10BASE-T1S Industrial PHY
 	  with MII interface.
 
+config LAN867X_PHY
+	tristate "Microchip 10BASE-T1S Ethernet PHY"
+	help
+		Currently supports the LAN8670, LAN8671, LAN8672
+
 config AT803X_PHY
 	tristate "Qualcomm Atheros AR803X PHYs and QCA833x PHYs"
 	depends on REGULATOR
diff --git a/drivers/net/phy/Makefile b/drivers/net/phy/Makefile
index b5138066ba04..a12c2f296297 100644
--- a/drivers/net/phy/Makefile
+++ b/drivers/net/phy/Makefile
@@ -78,6 +78,7 @@ obj-$(CONFIG_MICROSEMI_PHY)	+= mscc/
 obj-$(CONFIG_MOTORCOMM_PHY)	+= motorcomm.o
 obj-$(CONFIG_NATIONAL_PHY)	+= national.o
 obj-$(CONFIG_NCN26000_PHY)	+= ncn26000.o
+obj-$(CONFIG_LAN867X_PHY) += lan867x.o
 obj-$(CONFIG_NXP_C45_TJA11XX_PHY)	+= nxp-c45-tja11xx.o
 obj-$(CONFIG_NXP_TJA11XX_PHY)	+= nxp-tja11xx.o
 obj-$(CONFIG_QSEMI_PHY)		+= qsemi.o
diff --git a/drivers/net/phy/lan867x.c b/drivers/net/phy/lan867x.c
new file mode 100644
index 000000000000..c861c46ed06b
--- /dev/null
+++ b/drivers/net/phy/lan867x.c
@@ -0,0 +1,144 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Driver for Microchip 10BASE-T1S LAN867X PHY
+ *
+ * Support: Microchip Phys:
+ *  lan8670, lan8671, lan8672
+ */
+
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/phy.h>
+
+#define PHY_ID_LAN867X 0x0007C160
+
+#define LAN867X_REG_IRQ_1_CTL 0x001C
+#define LAN867X_REG_IRQ_2_CTL 0x001D
+
+static int lan867x_config_init(struct phy_device *phydev)
+{
+	/* HW quirk: Microchip states in the application note (AN1699) for the phy
+	 * that a set of read-modify-write (rmw) operations has to be performed
+	 * on a set of seemingly magic registers.
+	 * The result of these operations is just described as 'optimal performance'
+	 * Microchip gives no explanation as to what these mmd regs do,
+	 * in fact they are marked as reserved in the datasheet.
+	 */
+
+	/* The arrays below are pulled from the following table from AN1699
+	 * Access MMD Address Value Mask
+	 * RMW 0x1F 0x00D0 0x0002 0x0E03
+	 * RMW 0x1F 0x00D1 0x0000 0x0300
+	 * RMW 0x1F 0x0084 0x3380 0xFFC0
+	 * RMW 0x1F 0x0085 0x0006 0x000F
+	 * RMW 0x1F 0x008A 0xC000 0xF800
+	 * RMW 0x1F 0x0087 0x801C 0x801C
+	 * RMW 0x1F 0x0088 0x033F 0x1FFF
+	 * W   0x1F 0x008B 0x0404 ------
+	 * RMW 0x1F 0x0080 0x0600 0x0600
+	 * RMW 0x1F 0x00F1 0x2400 0x7F00
+	 * RMW 0x1F 0x0096 0x2000 0x2000
+	 * W   0x1F 0x0099 0x7F80 ------
+	 */
+
+	const int registers[12] = {
+		0x00D0, 0x00D1, 0x0084, 0x0085,
+		0x008A, 0x0087, 0x0088, 0x008B,
+		0x0080, 0x00F1, 0x0096, 0x0099,
+	};
+
+	const int masks[12] = {
+		0x0E03, 0x0300, 0xFFC0, 0x000F,
+		0xF800, 0x801C, 0x1FFF, 0xFFFF,
+		0x0600, 0x7F00, 0x2000, 0xFFFF,
+	};
+
+	const int values[12] = {
+		0x0002, 0x0000, 0x3380, 0x0006,
+		0xC000, 0x801C, 0x033F, 0x0404,
+		0x0600, 0x2400, 0x2000, 0x7F80,
+	};
+
+	int err;
+	int reg;
+	int reg_value;
+
+	/* Read-Modified Write Pseudocode (from AN1699)
+	 * current_val = read_register(mmd, addr) // Read current register value
+	 * new_val = current_val AND (NOT mask) // Clear bit fields to be written
+	 * new_val = new_val OR value // Set bits
+	 * write_register(mmd, addr, new_val) // Write back updated register value
+	 */
+	for (int i = 0; i < ARRAY_SIZE(registers); i++) {
+		reg = registers[i];
+		reg_value = phy_read_mmd(phydev, MDIO_MMD_VEND2, reg);
+		reg_value &= ~masks[i];
+		reg_value |= values[i];
+		err = phy_write_mmd(phydev, MDIO_MMD_VEND2, reg, reg_value);
+		if (err != 0)
+			return err;
+	}
+
+	return 0;
+}
+
+static int lan867x_config_interrupt(struct phy_device *phydev)
+{
+	/* None of the interrupts in the lan867x phy seem relevant.
+	 * Other phys inspect the link status and call phy_trigger_machine
+	 * on change.
+	 * This phy does not support link status, and thus has no interrupt
+	 * for it either.
+	 * So we'll just disable all interrupts instead.
+	 */
+
+	int err;
+
+	err = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_IRQ_1_CTL, 0xFFFF);
+	if (err)
+		return err;
+	err = phy_write_mmd(phydev, MDIO_MMD_VEND2, LAN867X_REG_IRQ_2_CTL, 0xFFFF);
+	return err;
+}
+
+static int lan867x_read_status(struct phy_device *phydev)
+{
+	/* The phy has some limitations, namely:
+	 *  - always reports link up
+	 *  - only supports 10MBit half duplex
+	 *  - does not support auto negotiate
+	 */
+	phydev->link = 1;
+	phydev->duplex = DUPLEX_HALF;
+	phydev->speed = SPEED_10;
+	phydev->autoneg = AUTONEG_DISABLE;
+
+	return 0;
+}
+
+static struct phy_driver lan867x_driver[] = {
+	{
+		PHY_ID_MATCH_MODEL(PHY_ID_LAN867X),
+		.name               = "LAN867X",
+		.features           = PHY_BASIC_T1S_P2MP_FEATURES,
+		.config_init        = lan867x_config_init,
+		.config_intr        = lan867x_config_interrupt,
+		.read_status        = lan867x_read_status,
+		.get_plca_cfg	    = genphy_c45_plca_get_cfg,
+		.set_plca_cfg	    = genphy_c45_plca_set_cfg,
+		.get_plca_status    = genphy_c45_plca_get_status,
+	}
+};
+
+module_phy_driver(lan867x_driver);
+
+static struct mdio_device_id __maybe_unused tbl[] = {
+	{ PHY_ID_MATCH_MODEL(PHY_ID_LAN867X) },
+	{ }
+};
+
+MODULE_DEVICE_TABLE(mdio, tbl);
+
+MODULE_DESCRIPTION("Microchip 10BASE-T1S lan867x Phy driver");
+MODULE_AUTHOR("Ramón Nordin Rodriguez");
+MODULE_LICENSE("GPL");
