@@ -522,7 +522,6 @@ Description: These files allow to each of ASICs by writing 1.
The files are write only.
-
What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/comm_chnl_ready
Date: July 2022
KernelVersion: 5.20
@@ -542,3 +541,124 @@ Description: The file indicates COME module hardware configuration.
The purpose is to expose some minor BOM changes for the same system SKU.
The file is read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_pwr_converter_fail
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: This file shows the system reset cause due to power converter
+ devices failure.
+ Value 1 in file means this is reset cause, 0 - otherwise.
+
+ The file is read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_ap_reset
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_ap_reset
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: These files aim to monitor the status of the External Root of Trust (EROT)
+ processor's RESET output to the Application Processor (AP).
+ By reading this file, could be determined if the EROT has invalidated or
+ revoked AP Firmware, at which point it will hold the AP in RESET until a
+ valid firmware is loaded. This protects the AP from running an
+ unauthorized firmware. In the normal flow, the AP reset should be released
+ after the EROT validates the integrity of the FW, and it should be done so
+ as quickly as possible so that the AP boots before the CPU starts to
+ communicate to each ASIC.
+
+ The files are read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_recovery
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_recovery
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_reset
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_reset
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: These files aim to perform External Root of Trust (EROT) recovery
+ sequence after EROT device failure.
+ These EROT devices protect ASICs from unauthorized access and in normal
+ flow their reset should be released with system power – earliest power
+ up stage, so that EROTs can begin boot and authentication process before
+ CPU starts to communicate to ASICs.
+ Issuing a reset to the EROT while asserting the recovery signal will cause
+ the EROT Application Processor to enter recovery mode so that the EROT FW
+ can be updated/recovered.
+ For reset/recovery the related file should be toggled by 1/0.
+
+ The files are read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot1_wp
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/erot2_wp
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: These files allow access to External Root of Trust (EROT) for reset
+ and recovery sequence after EROT device failure.
+ Default is 0 (programming disabled).
+ If the system is in locked-down mode writing this file will not be allowed.
+
+ The files are read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/spi_chnl_select
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: This file allows SPI chip selection for External Root of Trust (EROT)
+ device Out-of-Band recovery.
+ File can be written with 0 or with 1. It selects which EROT can be accessed
+ through SPI device.
+
+ The file is read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/asic_pg_fail
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak vadimp@nvidia.com
+Description: This file shows ASIC Power Good status.
+ Value 1 in file means ASIC Power Good failed, 0 - otherwise.
+
+ The file is read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd1_boot_fail
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd2_boot_fail
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd_fail
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak vadimp@nvidia.com
+Description: These files are related to clock boards status in system.
+ - clk_brd1_boot_fail: warning about 1-st clock board failed to boot from CI.
+ - clk_brd2_boot_fail: warning about 2-nd clock board failed to boot from CI.
+ - clk_brd_fail: error about common clock board boot failure.
+
+ The files are read only.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/clk_brd_prog_en
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: This file enables programming of clock boards.
+ Default is 0 (programming disabled).
+ If the system is in locked-down mode writing this file will not be allowed.
+
+ The file is read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/pwr_converter_prog_en
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: This file enables programming of power converters.
+ Default is 0 (programming disabled).
+ If the system is in locked-down mode writing this file will not be allowed.
+
+ The file is read/write.
+
+What: /sys/devices/platform/mlxplat/mlxreg-io/hwmon/hwmon*/reset_ac_ok_fail
+Date: February 2023
+KernelVersion: 6.3
+Contact: Vadim Pasternak <vadimp@nvidia.com>
+Description: This file shows the system reset cause due to AC power failure.
+ Value 1 in file means this is reset cause, 0 - otherwise.
+
+ The file is read only.