diff mbox series

[v2,04/11] next-cube.c: update scr_ops to properly use modern memory API

Message ID 20231220131641.592826-5-mark.cave-ayland@ilande.co.uk (mailing list archive)
State New, archived
Headers show
Series next-cube: various tidy-ups and improvements | expand

Commit Message

Mark Cave-Ayland Dec. 20, 2023, 1:16 p.m. UTC 
The old QEMU memory accessors used in the original NextCube patch series had
separate functions for 1, 2 and 4 byte accessors. When the series was finally
merged a simple wrapper function was written to dispatch the memory accesses
using the original functions.

Convert scr_ops to use the memory API directly renaming it to next_scr_ops,
marking it as DEVICE_BIG_ENDIAN, and handling any unaligned accesses.

Signed-off-by: Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>
Reviewed-by: Thomas Huth <huth@tuxfamily.org>
---
 hw/m68k/next-cube.c | 155 ++++++++++++++++----------------------------
 1 file changed, 55 insertions(+), 100 deletions(-)
diff mbox series

Patch

diff --git a/hw/m68k/next-cube.c b/hw/m68k/next-cube.c
index f73f563ac1..8ed9bac26d 100644
--- a/hw/m68k/next-cube.c
+++ b/hw/m68k/next-cube.c
@@ -335,81 +335,80 @@  static const MemoryRegionOps next_mmio_ops = {
     .endianness = DEVICE_BIG_ENDIAN,
 };
 
-static uint32_t scr_readb(NeXTPC *s, hwaddr addr)
+#define SCSICSR_ENABLE  0x01
+#define SCSICSR_RESET   0x02  /* reset scsi dma */
+#define SCSICSR_FIFOFL  0x04
+#define SCSICSR_DMADIR  0x08  /* if set, scsi to mem */
+#define SCSICSR_CPUDMA  0x10  /* if set, dma enabled */
+#define SCSICSR_INTMASK 0x20  /* if set, interrupt enabled */
+
+static uint64_t next_scr_readfn(void *opaque, hwaddr addr, unsigned size)
 {
+    NeXTPC *s = NEXT_PC(opaque);
+    uint64_t val;
+
     switch (addr) {
     case 0x14108:
         DPRINTF("FD read @ %x\n", (unsigned int)addr);
-        return 0x40 | 0x04 | 0x2 | 0x1;
+        val = 0x40 | 0x04 | 0x2 | 0x1;
+        break;
+
     case 0x14020:
         DPRINTF("SCSI 4020  STATUS READ %X\n", s->scsi_csr_1);
-        return s->scsi_csr_1;
+        val = s->scsi_csr_1;
+        break;
 
     case 0x14021:
         DPRINTF("SCSI 4021 STATUS READ %X\n", s->scsi_csr_2);
-        return 0x40;
+        val = 0x40;
+        break;
 
     /*
      * These 4 registers are the hardware timer, not sure which register
-     * is the latch instead of data, but no problems so far
+     * is the latch instead of data, but no problems so far.
+     *
+     * Hack: We need to have the LSB change consistently to make it work
      */
-    case 0x1a000:
-        return 0xff & (clock() >> 24);
-    case 0x1a001:
-        return 0xff & (clock() >> 16);
-    case 0x1a002:
-        return 0xff & (clock() >> 8);
-    case 0x1a003:
-        /* Hack: We need to have this change consistently to make it work */
-        return 0xFF & clock();
+    case 0x1a000 ... 0x1a003:
+        val = extract32(clock(), (4 - (addr - 0x1a000) - size) << 3,
+                        size << 3);
+        break;
 
     /* For now return dummy byte to allow the Ethernet test to timeout */
     case 0x6000:
-        return 0xff;
+        val = 0xff;
+        break;
 
     default:
-        DPRINTF("BMAP Read B @ %x\n", (unsigned int)addr);
-        return 0;
+        DPRINTF("BMAP Read @ 0x%x size %u\n", (unsigned int)addr, size);
+        val = 0;
+        break;
     }
-}
 
-static uint32_t scr_readw(NeXTPC *s, hwaddr addr)
-{
-    DPRINTF("BMAP Read W @ %x\n", (unsigned int)addr);
-    return 0;
+    return val;
 }
 
-static uint32_t scr_readl(NeXTPC *s, hwaddr addr)
+static void next_scr_writefn(void *opaque, hwaddr addr, uint64_t val,
+                             unsigned size)
 {
-    DPRINTF("BMAP Read L @ %x\n", (unsigned int)addr);
-    return 0;
-}
-
-#define SCSICSR_ENABLE  0x01
-#define SCSICSR_RESET   0x02  /* reset scsi dma */
-#define SCSICSR_FIFOFL  0x04
-#define SCSICSR_DMADIR  0x08  /* if set, scsi to mem */
-#define SCSICSR_CPUDMA  0x10  /* if set, dma enabled */
-#define SCSICSR_INTMASK 0x20  /* if set, interrupt enabled */
+    NeXTPC *s = NEXT_PC(opaque);
 
-static void scr_writeb(NeXTPC *s, hwaddr addr, uint32_t value)
-{
     switch (addr) {
     case 0x14108:
         DPRINTF("FDCSR Write: %x\n", value);
-
-        if (value == 0x0) {
+        if (val == 0x0) {
             /* qemu_irq_raise(s->fd_irq[0]); */
         }
         break;
+
     case 0x14020: /* SCSI Control Register */
-        if (value & SCSICSR_FIFOFL) {
+        if (val & SCSICSR_FIFOFL) {
             DPRINTF("SCSICSR FIFO Flush\n");
             /* will have to add another irq to the esp if this is needed */
             /* esp_puflush_fifo(esp_g); */
         }
 
-        if (value & SCSICSR_ENABLE) {
+        if (val & SCSICSR_ENABLE) {
             DPRINTF("SCSICSR Enable\n");
             /*
              * qemu_irq_raise(s->scsi_dma);
@@ -423,17 +422,17 @@  static void scr_writeb(NeXTPC *s, hwaddr addr, uint32_t value)
          *     s->scsi_csr_1 &= ~SCSICSR_ENABLE;
          */
 
-        if (value & SCSICSR_RESET) {
+        if (val & SCSICSR_RESET) {
             DPRINTF("SCSICSR Reset\n");
             /* I think this should set DMADIR. CPUDMA and INTMASK to 0 */
             qemu_irq_raise(s->scsi_reset);
             s->scsi_csr_1 &= ~(SCSICSR_INTMASK | 0x80 | 0x1);
             qemu_irq_lower(s->scsi_reset);
         }
-        if (value & SCSICSR_DMADIR) {
+        if (val & SCSICSR_DMADIR) {
             DPRINTF("SCSICSR DMAdir\n");
         }
-        if (value & SCSICSR_CPUDMA) {
+        if (val & SCSICSR_CPUDMA) {
             DPRINTF("SCSICSR CPUDMA\n");
             /* qemu_irq_raise(s->scsi_dma); */
             s->int_status |= 0x4000000;
@@ -442,11 +441,11 @@  static void scr_writeb(NeXTPC *s, hwaddr addr, uint32_t value)
             s->int_status &= ~(0x4000000);
             /* qemu_irq_lower(s->scsi_dma); */
         }
-        if (value & SCSICSR_INTMASK) {
+        if (val & SCSICSR_INTMASK) {
             DPRINTF("SCSICSR INTMASK\n");
             /*
              * int_mask &= ~0x1000;
-             * s->scsi_csr_1 |= value;
+             * s->scsi_csr_1 |= val;
              * s->scsi_csr_1 &= ~SCSICSR_INTMASK;
              * if (s->scsi_queued) {
              *     s->scsi_queued = 0;
@@ -456,72 +455,28 @@  static void scr_writeb(NeXTPC *s, hwaddr addr, uint32_t value)
         } else {
             /* int_mask |= 0x1000; */
         }
-        if (value & 0x80) {
+        if (val & 0x80) {
             /* int_mask |= 0x1000; */
             /* s->scsi_csr_1 |= 0x80; */
         }
-        DPRINTF("SCSICSR Write: %x\n", value);
-        /* s->scsi_csr_1 = value; */
-        return;
+        DPRINTF("SCSICSR Write: %x\n", val);
+        /* s->scsi_csr_1 = val; */
+        break;
+
     /* Hardware timer latch - not implemented yet */
     case 0x1a000:
     default:
-        DPRINTF("BMAP Write B @ %x with %x\n", (unsigned int)addr, value);
+        DPRINTF("BMAP Write @ 0x%x with 0x%x size %u\n", (unsigned int)addr,
+                val, size);
     }
 }
 
-static void scr_writew(NeXTPC *s, hwaddr addr, uint32_t value)
-{
-    DPRINTF("BMAP Write W @ %x with %x\n", (unsigned int)addr, value);
-}
-
-static void scr_writel(NeXTPC *s, hwaddr addr, uint32_t value)
-{
-    DPRINTF("BMAP Write L @ %x with %x\n", (unsigned int)addr, value);
-}
-
-static uint64_t scr_readfn(void *opaque, hwaddr addr, unsigned size)
-{
-    NeXTPC *s = NEXT_PC(opaque);
-
-    switch (size) {
-    case 1:
-        return scr_readb(s, addr);
-    case 2:
-        return scr_readw(s, addr);
-    case 4:
-        return scr_readl(s, addr);
-    default:
-        g_assert_not_reached();
-    }
-}
-
-static void scr_writefn(void *opaque, hwaddr addr, uint64_t value,
-                        unsigned size)
-{
-    NeXTPC *s = NEXT_PC(opaque);
-
-    switch (size) {
-    case 1:
-        scr_writeb(s, addr, value);
-        break;
-    case 2:
-        scr_writew(s, addr, value);
-        break;
-    case 4:
-        scr_writel(s, addr, value);
-        break;
-    default:
-        g_assert_not_reached();
-    }
-}
-
-static const MemoryRegionOps scr_ops = {
-    .read = scr_readfn,
-    .write = scr_writefn,
+static const MemoryRegionOps next_scr_ops = {
+    .read = next_scr_readfn,
+    .write = next_scr_writefn,
     .valid.min_access_size = 1,
     .valid.max_access_size = 4,
-    .endianness = DEVICE_NATIVE_ENDIAN,
+    .endianness = DEVICE_BIG_ENDIAN,
 };
 
 #define NEXTDMA_SCSI(x)      (0x10 + x)
@@ -912,7 +867,7 @@  static void next_pc_realize(DeviceState *dev, Error **errp)
 
     memory_region_init_io(&s->mmiomem, OBJECT(s), &next_mmio_ops, s,
                           "next.mmio", 0xd0000);
-    memory_region_init_io(&s->scrmem, OBJECT(s), &scr_ops, s,
+    memory_region_init_io(&s->scrmem, OBJECT(s), &next_scr_ops, s,
                           "next.scr", 0x20000);
     sysbus_init_mmio(sbd, &s->mmiomem);
     sysbus_init_mmio(sbd, &s->scrmem);