@@ -376,6 +376,81 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len,
}
/*
+ * Read an address range from the flash chip page by page.
+ * Some controller has transaction length limitation such as the
+ * Freescale's eSPI controller can only trasmit 0xFFFF bytes one
+ * time, so we have to read page by page if the len is more than
+ * the limitation.
+ */
+static int m25p80_page_read(struct mtd_info *mtd, loff_t from, size_t len,
+ size_t *retlen, u_char *buf)
+{
+ struct m25p *flash = mtd_to_m25p(mtd);
+ struct spi_transfer t[2];
+ struct spi_message m;
+ u32 i, page_size = 0;
+
+ DEBUG(MTD_DEBUG_LEVEL2, "%s: %s %s 0x%08x, len %zd\n",
+ dev_name(&flash->spi->dev), __func__, "from",
+ (u32)from, len);
+
+ /* sanity checks */
+ if (!len)
+ return 0;
+
+ if (from + len > flash->mtd.size)
+ return -EINVAL;
+
+ spi_message_init(&m);
+ memset(t, 0, (sizeof t));
+
+ /* NOTE:
+ * OPCODE_FAST_READ (if available) is faster.
+ * Should add 1 byte DUMMY_BYTE.
+ */
+ t[0].tx_buf = flash->command;
+ t[0].len = m25p_cmdsz(flash) + FAST_READ_DUMMY_BYTE;
+ spi_message_add_tail(&t[0], &m);
+
+ t[1].rx_buf = buf;
+ spi_message_add_tail(&t[1], &m);
+
+ /* Byte count starts at zero. */
+ if (retlen)
+ *retlen = 0;
+
+ mutex_lock(&flash->lock);
+
+ /* Wait till previous write/erase is done. */
+ if (wait_till_ready(flash)) {
+ /* REVISIT status return?? */
+ mutex_unlock(&flash->lock);
+ return 1;
+ }
+
+ /* Set up the write data buffer. */
+ flash->command[0] = OPCODE_READ;
+
+ for (i = page_size; i < len; i += page_size) {
+ page_size = len - i;
+ if (page_size > flash->page_size)
+ page_size = flash->page_size;
+ m25p_addr2cmd(flash, from + i, flash->command);
+ t[1].len = page_size;
+ t[1].rx_buf = buf + i;
+
+ spi_sync(flash->spi, &m);
+
+ *retlen += m.actual_length - m25p_cmdsz(flash)
+ - FAST_READ_DUMMY_BYTE;
+ }
+
+ mutex_unlock(&flash->lock);
+
+ return 0;
+}
+
+/*
* Write an address range to the flash chip. Data must be written in
* FLASH_PAGESIZE chunks. The address range may be any size provided
* it is within the physical boundaries.
@@ -877,6 +952,9 @@ static int __devinit m25p_probe(struct spi_device *spi)
flash->mtd.erase = m25p80_erase;
flash->mtd.read = m25p80_read;
+ if (spi->master->flags & SPI_MASTER_TRANS_LIMIT)
+ flash->mtd.read = m25p80_page_read;
+
/* sst flash chips use AAI word program */
if (info->jedec_id >> 16 == 0xbf)
flash->mtd.write = sst_write;
@@ -470,6 +470,7 @@ static struct spi_master * __devinit fsl_espi_probe(struct device *dev,
goto err_probe;
master->setup = fsl_espi_setup;
+ master->flags = SPI_MASTER_TRANS_LIMIT;
mpc8xxx_spi = spi_master_get_devdata(master);
mpc8xxx_spi->spi_do_one_msg = fsl_espi_do_one_msg;
@@ -261,6 +261,7 @@ struct spi_master {
#define SPI_MASTER_HALF_DUPLEX BIT(0) /* can't do full duplex */
#define SPI_MASTER_NO_RX BIT(1) /* can't do buffer read */
#define SPI_MASTER_NO_TX BIT(2) /* can't do buffer write */
+#define SPI_MASTER_TRANS_LIMIT BIT(3) /* have trans length limit */
/* Setup mode and clock, etc (spi driver may call many times).
*