diff mbox

[3/5] ARM: U300: spi->mode and spi_bits_per_words updates

Message ID 1284135579-13578-4-git-send-email-wellsk40@gmail.com (mailing list archive)
State Superseded
Headers show

Commit Message

wellsk40@gmail.com Sept. 10, 2010, 4:19 p.m. UTC 
None
diff mbox

Patch

diff --git a/arch/arm/mach-u300/dummyspichip.c b/arch/arm/mach-u300/dummyspichip.c
index 5f55012..03f7936 100644
--- a/arch/arm/mach-u300/dummyspichip.c
+++ b/arch/arm/mach-u300/dummyspichip.c
@@ -46,7 +46,6 @@  static ssize_t dummy_looptest(struct device *dev,
 	 * struct, this is just used here to alter the behaviour of the chip
 	 * in order to perform tests.
 	 */
-	struct pl022_config_chip *chip_info = spi->controller_data;
 	int status;
 	u8 txbuf[14] = {0xDE, 0xAD, 0xBE, 0xEF, 0x2B, 0xAD,
 			0xCA, 0xFE, 0xBA, 0xBE, 0xB1, 0x05,
@@ -72,7 +71,7 @@  static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 8 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_8;
+	spi->bits_per_word = 8;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
@@ -159,7 +158,7 @@  static ssize_t dummy_looptest(struct device *dev,
 	 * Force chip to 16 bit mode
 	 * WARNING: NEVER DO THIS IN REAL DRIVER CODE, THIS SHOULD BE STATIC!
 	 */
-	chip_info->data_size = SSP_DATA_BITS_16;
+	spi->bits_per_word = 16;
 	/* You should NOT DO THIS EITHER */
 	spi->master->setup(spi);
 
diff --git a/arch/arm/mach-u300/spi.c b/arch/arm/mach-u300/spi.c
index f0e887b..edb2c0d 100644
--- a/arch/arm/mach-u300/spi.c
+++ b/arch/arm/mach-u300/spi.c
@@ -30,8 +30,6 @@  static void select_dummy_chip(u32 chipselect)
 }
 
 struct pl022_config_chip dummy_chip_info = {
-	/* Nominally this is LOOPBACK_DISABLED, but this is our dummy chip! */
-	.lbm = LOOPBACK_ENABLED,
 	/*
 	 * available POLLING_TRANSFER and INTERRUPT_TRANSFER,
 	 * DMA_TRANSFER does not work
@@ -42,14 +40,8 @@  struct pl022_config_chip dummy_chip_info = {
 	.hierarchy = SSP_MASTER,
 	/* 0 = drive TX even as slave, 1 = do not drive TX as slave */
 	.slave_tx_disable = 0,
-	/* LSB first */
-	.endian_tx = SSP_TX_LSB,
-	.endian_rx = SSP_RX_LSB,
-	.data_size = SSP_DATA_BITS_8, /* used to be 12 in some default */
 	.rx_lev_trig = SSP_RX_1_OR_MORE_ELEM,
 	.tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC,
-	.clk_phase = SSP_CLK_SECOND_EDGE,
-	.clk_pol = SSP_CLK_POL_IDLE_LOW,
 	.ctrl_len = SSP_BITS_12,
 	.wait_state = SSP_MWIRE_WAIT_ZERO,
 	.duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX,
@@ -75,7 +67,7 @@  static struct spi_board_info u300_spi_devices[] = {
 		.bus_num        = 0, /* Only one bus on this chip */
 		.chip_select    = 0,
 		/* Means SPI_CS_HIGH, change if e.g low CS */
-		.mode           = 0,
+		.mode           = SPI_MODE_1 | SPI_LSB_FIRST | SPI_LOOP,
 	},
 #endif
 };