@@ -1597,58 +1597,58 @@ static int verify_controller_parameters(struct pl022 *pl022,
{
if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI)
|| (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"interface is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->iface == SSP_INTERFACE_UNIDIRECTIONAL) &&
(!pl022->vendor->unidir)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"unidirectional mode not supported in this "
"hardware version\n");
return -EINVAL;
}
if ((chip_info->hierarchy != SSP_MASTER)
&& (chip_info->hierarchy != SSP_SLAVE)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"hierarchy is configured incorrectly\n");
return -EINVAL;
}
if (((chip_info->clk_freq).cpsdvsr < CPSDVR_MIN)
|| ((chip_info->clk_freq).cpsdvsr > CPSDVR_MAX)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"cpsdvsr is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->com_mode != INTERRUPT_TRANSFER)
&& (chip_info->com_mode != DMA_TRANSFER)
&& (chip_info->com_mode != POLLING_TRANSFER)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Communication mode is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->rx_lev_trig < SSP_RX_1_OR_MORE_ELEM)
|| (chip_info->rx_lev_trig > SSP_RX_32_OR_MORE_ELEM)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"RX FIFO Trigger Level is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->tx_lev_trig < SSP_TX_1_OR_MORE_EMPTY_LOC)
|| (chip_info->tx_lev_trig > SSP_TX_32_OR_MORE_EMPTY_LOC)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"TX FIFO Trigger Level is configured incorrectly\n");
return -EINVAL;
}
if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) {
if ((chip_info->ctrl_len < SSP_BITS_4)
|| (chip_info->ctrl_len > SSP_BITS_32)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"CTRL LEN is configured incorrectly\n");
return -EINVAL;
}
if ((chip_info->wait_state != SSP_MWIRE_WAIT_ZERO)
&& (chip_info->wait_state != SSP_MWIRE_WAIT_ONE)) {
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Wait State is configured incorrectly\n");
return -EINVAL;
}
@@ -1658,12 +1658,12 @@ static int verify_controller_parameters(struct pl022 *pl022,
SSP_MICROWIRE_CHANNEL_FULL_DUPLEX)
&& (chip_info->duplex !=
SSP_MICROWIRE_CHANNEL_HALF_DUPLEX))
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Microwire duplex mode is configured incorrectly\n");
return -EINVAL;
} else {
if (chip_info->duplex != SSP_MICROWIRE_CHANNEL_FULL_DUPLEX)
- dev_err(chip_info->dev,
+ dev_err(&pl022->adev->dev,
"Microwire half duplex mode requested,"
" but this is only available in the"
" ST version of PL022\n");
@@ -1671,7 +1671,7 @@ static int verify_controller_parameters(struct pl022 *pl022,
}
}
if (chip_info->cs_control == NULL) {
- dev_warn(chip_info->dev,
+ dev_warn(&pl022->adev->dev,
"Chip Select Function is NULL for this chip\n");
chip_info->cs_control = null_cs_control;
}
@@ -1851,9 +1851,6 @@ static int pl022_setup(struct spi_device *spi)
"using user supplied controller_data settings\n");
}
- /* Pointer back to the SPI device */
- chip_info->dev = &spi->dev;
-
/*
* We can override with custom divisors, else we use the board
* frequency setting
@@ -276,7 +276,6 @@ struct pl022_ssp_controller {
* @dma_config: DMA configuration for SSP controller and peripheral
*/
struct pl022_config_chip {
- struct device *dev;
enum ssp_interface iface;
enum ssp_hierarchy hierarchy;
bool slave_tx_disable;