diff --git a/arch/arm/common/Kconfig b/arch/arm/common/Kconfig
index c3a4e9c..76c9970 100644
--- a/arch/arm/common/Kconfig
+++ b/arch/arm/common/Kconfig
@@ -9,9 +9,6 @@ config DMABOUNCE
 	bool
 	select ZONE_DMA
 
-config SHARP_LOCOMO
-	bool
-
 config SHARP_PARAM
 	bool
 
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 70b1eff..437c79a 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -7,7 +7,6 @@ obj-y				+= firmware.o
 obj-$(CONFIG_ICST)		+= icst.o
 obj-$(CONFIG_SA1111)		+= sa1111.o
 obj-$(CONFIG_DMABOUNCE)		+= dmabounce.o
-obj-$(CONFIG_SHARP_LOCOMO)	+= locomo.o
 obj-$(CONFIG_SHARP_PARAM)	+= sharpsl_param.o
 obj-$(CONFIG_SHARP_SCOOP)	+= scoop.o
 obj-$(CONFIG_PCI_HOST_ITE8152)  += it8152.o
diff --git a/arch/arm/common/locomo.c b/arch/arm/common/locomo.c
deleted file mode 100644
index b55c362..0000000
--- a/arch/arm/common/locomo.c
+++ /dev/null
@@ -1,914 +0,0 @@
-/*
- * linux/arch/arm/common/locomo.c
- *
- * Sharp LoCoMo support
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- *
- * This file contains all generic LoCoMo support.
- *
- * All initialization functions provided here are intended to be called
- * from machine specific code with proper arguments when required.
- *
- * Based on sa1111.c
- */
-
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/kernel.h>
-#include <linux/delay.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/platform_device.h>
-#include <linux/slab.h>
-#include <linux/spinlock.h>
-#include <linux/io.h>
-
-#include <mach/hardware.h>
-#include <asm/irq.h>
-#include <asm/mach/irq.h>
-
-#include <asm/hardware/locomo.h>
-
-/* LoCoMo Interrupts */
-#define IRQ_LOCOMO_KEY		(0)
-#define IRQ_LOCOMO_GPIO		(1)
-#define IRQ_LOCOMO_LT		(2)
-#define IRQ_LOCOMO_SPI		(3)
-
-/* M62332 output channel selection */
-#define M62332_EVR_CH	1	/* M62332 volume channel number  */
-				/*   0 : CH.1 , 1 : CH. 2        */
-/* DAC send data */
-#define	M62332_SLAVE_ADDR	0x4e	/* Slave address  */
-#define	M62332_W_BIT		0x00	/* W bit (0 only) */
-#define	M62332_SUB_ADDR		0x00	/* Sub address    */
-#define	M62332_A_BIT		0x00	/* A bit (0 only) */
-
-/* DAC setup and hold times (expressed in us) */
-#define DAC_BUS_FREE_TIME	5	/*   4.7 us */
-#define DAC_START_SETUP_TIME	5	/*   4.7 us */
-#define DAC_STOP_SETUP_TIME	4	/*   4.0 us */
-#define DAC_START_HOLD_TIME	5	/*   4.7 us */
-#define DAC_SCL_LOW_HOLD_TIME	5	/*   4.7 us */
-#define DAC_SCL_HIGH_HOLD_TIME	4	/*   4.0 us */
-#define DAC_DATA_SETUP_TIME	1	/*   250 ns */
-#define DAC_DATA_HOLD_TIME	1	/*   300 ns */
-#define DAC_LOW_SETUP_TIME	1	/*   300 ns */
-#define DAC_HIGH_SETUP_TIME	1	/*  1000 ns */
-
-/* the following is the overall data for the locomo chip */
-struct locomo {
-	struct device *dev;
-	unsigned long phys;
-	unsigned int irq;
-	int irq_base;
-	spinlock_t lock;
-	void __iomem *base;
-#ifdef CONFIG_PM
-	void *saved_state;
-#endif
-};
-
-struct locomo_dev_info {
-	unsigned long	offset;
-	unsigned long	length;
-	unsigned int	devid;
-	unsigned int	irq[1];
-	const char *	name;
-};
-
-/* All the locomo devices.  If offset is non-zero, the mapbase for the
- * locomo_dev will be set to the chip base plus offset.  If offset is
- * zero, then the mapbase for the locomo_dev will be set to zero.  An
- * offset of zero means the device only uses GPIOs or other helper
- * functions inside this file */
-static struct locomo_dev_info locomo_devices[] = {
-	{
-		.devid 		= LOCOMO_DEVID_KEYBOARD,
-		.irq		= { IRQ_LOCOMO_KEY },
-		.name		= "locomo-keyboard",
-		.offset		= LOCOMO_KEYBOARD,
-		.length		= 16,
-	},
-	{
-		.devid		= LOCOMO_DEVID_FRONTLIGHT,
-		.irq		= {},
-		.name		= "locomo-frontlight",
-		.offset		= LOCOMO_FRONTLIGHT,
-		.length		= 8,
-
-	},
-	{
-		.devid		= LOCOMO_DEVID_BACKLIGHT,
-		.irq		= {},
-		.name		= "locomo-backlight",
-		.offset		= LOCOMO_BACKLIGHT,
-		.length		= 8,
-	},
-	{
-		.devid		= LOCOMO_DEVID_AUDIO,
-		.irq		= {},
-		.name		= "locomo-audio",
-		.offset		= LOCOMO_AUDIO,
-		.length		= 4,
-	},
-	{
-		.devid		= LOCOMO_DEVID_LED,
-		.irq 		= {},
-		.name		= "locomo-led",
-		.offset		= LOCOMO_LED,
-		.length		= 8,
-	},
-	{
-		.devid		= LOCOMO_DEVID_UART,
-		.irq		= {},
-		.name		= "locomo-uart",
-		.offset		= 0,
-		.length		= 0,
-	},
-	{
-		.devid		= LOCOMO_DEVID_SPI,
-		.irq		= {},
-		.name		= "locomo-spi",
-		.offset		= LOCOMO_SPI,
-		.length		= 0x30,
-	},
-};
-
-static void locomo_handler(unsigned int irq, struct irq_desc *desc)
-{
-	struct locomo *lchip = irq_get_chip_data(irq);
-	int req, i;
-
-	/* Acknowledge the parent IRQ */
-	desc->irq_data.chip->irq_ack(&desc->irq_data);
-
-	/* check why this interrupt was generated */
-	req = locomo_readl(lchip->base + LOCOMO_ICR) & 0x0f00;
-
-	if (req) {
-		/* generate the next interrupt(s) */
-		irq = lchip->irq_base;
-		for (i = 0; i <= 3; i++, irq++) {
-			if (req & (0x0100 << i)) {
-				generic_handle_irq(irq);
-			}
-
-		}
-	}
-}
-
-static void locomo_ack_irq(struct irq_data *d)
-{
-}
-
-static void locomo_mask_irq(struct irq_data *d)
-{
-	struct locomo *lchip = irq_data_get_irq_chip_data(d);
-	unsigned int r;
-	r = locomo_readl(lchip->base + LOCOMO_ICR);
-	r &= ~(0x0010 << (d->irq - lchip->irq_base));
-	locomo_writel(r, lchip->base + LOCOMO_ICR);
-}
-
-static void locomo_unmask_irq(struct irq_data *d)
-{
-	struct locomo *lchip = irq_data_get_irq_chip_data(d);
-	unsigned int r;
-	r = locomo_readl(lchip->base + LOCOMO_ICR);
-	r |= (0x0010 << (d->irq - lchip->irq_base));
-	locomo_writel(r, lchip->base + LOCOMO_ICR);
-}
-
-static struct irq_chip locomo_chip = {
-	.name		= "LOCOMO",
-	.irq_ack	= locomo_ack_irq,
-	.irq_mask	= locomo_mask_irq,
-	.irq_unmask	= locomo_unmask_irq,
-};
-
-static void locomo_setup_irq(struct locomo *lchip)
-{
-	int irq = lchip->irq_base;
-
-	/*
-	 * Install handler for IRQ_LOCOMO_HW.
-	 */
-	irq_set_irq_type(lchip->irq, IRQ_TYPE_EDGE_FALLING);
-	irq_set_chip_data(lchip->irq, lchip);
-	irq_set_chained_handler(lchip->irq, locomo_handler);
-
-	/* Install handlers for IRQ_LOCOMO_* */
-	for ( ; irq <= lchip->irq_base + 3; irq++) {
-		irq_set_chip_and_handler(irq, &locomo_chip, handle_level_irq);
-		irq_set_chip_data(irq, lchip);
-		set_irq_flags(irq, IRQF_VALID | IRQF_PROBE);
-	}
-}
-
-
-static void locomo_dev_release(struct device *_dev)
-{
-	struct locomo_dev *dev = LOCOMO_DEV(_dev);
-
-	kfree(dev);
-}
-
-static int
-locomo_init_one_child(struct locomo *lchip, struct locomo_dev_info *info)
-{
-	struct locomo_dev *dev;
-	int ret;
-
-	dev = kzalloc(sizeof(struct locomo_dev), GFP_KERNEL);
-	if (!dev) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	/*
-	 * If the parent device has a DMA mask associated with it,
-	 * propagate it down to the children.
-	 */
-	if (lchip->dev->dma_mask) {
-		dev->dma_mask = *lchip->dev->dma_mask;
-		dev->dev.dma_mask = &dev->dma_mask;
-	}
-
-	dev_set_name(&dev->dev, "%s", info->name);
-	dev->devid	 = info->devid;
-	dev->dev.parent  = lchip->dev;
-	dev->dev.bus     = &locomo_bus_type;
-	dev->dev.release = locomo_dev_release;
-	dev->dev.coherent_dma_mask = lchip->dev->coherent_dma_mask;
-
-	if (info->offset)
-		dev->mapbase = lchip->base + info->offset;
-	else
-		dev->mapbase = 0;
-	dev->length = info->length;
-
-	dev->irq[0] = (lchip->irq_base == NO_IRQ) ?
-			NO_IRQ : lchip->irq_base + info->irq[0];
-
-	ret = device_register(&dev->dev);
-	if (ret) {
- out:
-		kfree(dev);
-	}
-	return ret;
-}
-
-#ifdef CONFIG_PM
-
-struct locomo_save_data {
-	u16	LCM_GPO;
-	u16	LCM_SPICT;
-	u16	LCM_GPE;
-	u16	LCM_ASD;
-	u16	LCM_SPIMD;
-};
-
-static int locomo_suspend(struct platform_device *dev, pm_message_t state)
-{
-	struct locomo *lchip = platform_get_drvdata(dev);
-	struct locomo_save_data *save;
-	unsigned long flags;
-
-	save = kmalloc(sizeof(struct locomo_save_data), GFP_KERNEL);
-	if (!save)
-		return -ENOMEM;
-
-	lchip->saved_state = save;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-
-	save->LCM_GPO     = locomo_readl(lchip->base + LOCOMO_GPO);	/* GPIO */
-	locomo_writel(0x00, lchip->base + LOCOMO_GPO);
-	save->LCM_SPICT   = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPICT);	/* SPI */
-	locomo_writel(0x40, lchip->base + LOCOMO_SPI + LOCOMO_SPICT);
-	save->LCM_GPE     = locomo_readl(lchip->base + LOCOMO_GPE);	/* GPIO */
-	locomo_writel(0x00, lchip->base + LOCOMO_GPE);
-	save->LCM_ASD     = locomo_readl(lchip->base + LOCOMO_ASD);	/* ADSTART */
-	locomo_writel(0x00, lchip->base + LOCOMO_ASD);
-	save->LCM_SPIMD   = locomo_readl(lchip->base + LOCOMO_SPI + LOCOMO_SPIMD);	/* SPI */
-	locomo_writel(0x3C14, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD);
-
-	locomo_writel(0x00, lchip->base + LOCOMO_PAIF);
-	locomo_writel(0x00, lchip->base + LOCOMO_DAC);
-	locomo_writel(0x00, lchip->base + LOCOMO_BACKLIGHT + LOCOMO_TC);
-
-	if ((locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT0) & 0x88) && (locomo_readl(lchip->base + LOCOMO_LED + LOCOMO_LPT1) & 0x88))
-		locomo_writel(0x00, lchip->base + LOCOMO_C32K); 	/* CLK32 off */
-	else
-		/* 18MHz already enabled, so no wait */
-		locomo_writel(0xc1, lchip->base + LOCOMO_C32K); 	/* CLK32 on */
-
-	locomo_writel(0x00, lchip->base + LOCOMO_TADC);		/* 18MHz clock off*/
-	locomo_writel(0x00, lchip->base + LOCOMO_AUDIO + LOCOMO_ACC);			/* 22MHz/24MHz clock off */
-	locomo_writel(0x00, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);			/* FL */
-
-	spin_unlock_irqrestore(&lchip->lock, flags);
-
-	return 0;
-}
-
-static int locomo_resume(struct platform_device *dev)
-{
-	struct locomo *lchip = platform_get_drvdata(dev);
-	struct locomo_save_data *save;
-	unsigned long r;
-	unsigned long flags;
-
-	save = lchip->saved_state;
-	if (!save)
-		return 0;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-
-	locomo_writel(save->LCM_GPO, lchip->base + LOCOMO_GPO);
-	locomo_writel(save->LCM_SPICT, lchip->base + LOCOMO_SPI + LOCOMO_SPICT);
-	locomo_writel(save->LCM_GPE, lchip->base + LOCOMO_GPE);
-	locomo_writel(save->LCM_ASD, lchip->base + LOCOMO_ASD);
-	locomo_writel(save->LCM_SPIMD, lchip->base + LOCOMO_SPI + LOCOMO_SPIMD);
-
-	locomo_writel(0x00, lchip->base + LOCOMO_C32K);
-	locomo_writel(0x90, lchip->base + LOCOMO_TADC);
-
-	locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KSC);
-	r = locomo_readl(lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC);
-	r &= 0xFEFF;
-	locomo_writel(r, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC);
-	locomo_writel(0x1, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KCMD);
-
-	spin_unlock_irqrestore(&lchip->lock, flags);
-
-	lchip->saved_state = NULL;
-	kfree(save);
-
-	return 0;
-}
-#endif
-
-
-/**
- *	locomo_probe - probe for a single LoCoMo chip.
- *	@phys_addr: physical address of device.
- *
- *	Probe for a LoCoMo chip.  This must be called
- *	before any other locomo-specific code.
- *
- *	Returns:
- *	%-ENODEV	device not found.
- *	%-EBUSY		physical address already marked in-use.
- *	%0		successful.
- */
-static int
-__locomo_probe(struct device *me, struct resource *mem, int irq)
-{
-	struct locomo_platform_data *pdata = me->platform_data;
-	struct locomo *lchip;
-	unsigned long r;
-	int i, ret = -ENODEV;
-
-	lchip = kzalloc(sizeof(struct locomo), GFP_KERNEL);
-	if (!lchip)
-		return -ENOMEM;
-
-	spin_lock_init(&lchip->lock);
-
-	lchip->dev = me;
-	dev_set_drvdata(lchip->dev, lchip);
-
-	lchip->phys = mem->start;
-	lchip->irq = irq;
-	lchip->irq_base = (pdata) ? pdata->irq_base : NO_IRQ;
-
-	/*
-	 * Map the whole region.  This also maps the
-	 * registers for our children.
-	 */
-	lchip->base = ioremap(mem->start, PAGE_SIZE);
-	if (!lchip->base) {
-		ret = -ENOMEM;
-		goto out;
-	}
-
-	/* locomo initialize */
-	locomo_writel(0, lchip->base + LOCOMO_ICR);
-	/* KEYBOARD */
-	locomo_writel(0, lchip->base + LOCOMO_KEYBOARD + LOCOMO_KIC);
-
-	/* GPIO */
-	locomo_writel(0, lchip->base + LOCOMO_GPO);
-	locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14))
-			, lchip->base + LOCOMO_GPE);
-	locomo_writel((LOCOMO_GPIO(1) | LOCOMO_GPIO(2) | LOCOMO_GPIO(13) | LOCOMO_GPIO(14))
-			, lchip->base + LOCOMO_GPD);
-	locomo_writel(0, lchip->base + LOCOMO_GIE);
-
-	/* Frontlight */
-	locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
-	locomo_writel(0, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD);
-
-	/* Longtime timer */
-	locomo_writel(0, lchip->base + LOCOMO_LTINT);
-	/* SPI */
-	locomo_writel(0, lchip->base + LOCOMO_SPI + LOCOMO_SPIIE);
-
-	locomo_writel(6 + 8 + 320 + 30 - 10, lchip->base + LOCOMO_ASD);
-	r = locomo_readl(lchip->base + LOCOMO_ASD);
-	r |= 0x8000;
-	locomo_writel(r, lchip->base + LOCOMO_ASD);
-
-	locomo_writel(6 + 8 + 320 + 30 - 10 - 128 + 4, lchip->base + LOCOMO_HSD);
-	r = locomo_readl(lchip->base + LOCOMO_HSD);
-	r |= 0x8000;
-	locomo_writel(r, lchip->base + LOCOMO_HSD);
-
-	locomo_writel(128 / 8, lchip->base + LOCOMO_HSC);
-
-	/* XON */
-	locomo_writel(0x80, lchip->base + LOCOMO_TADC);
-	udelay(1000);
-	/* CLK9MEN */
-	r = locomo_readl(lchip->base + LOCOMO_TADC);
-	r |= 0x10;
-	locomo_writel(r, lchip->base + LOCOMO_TADC);
-	udelay(100);
-
-	/* init DAC */
-	r = locomo_readl(lchip->base + LOCOMO_DAC);
-	r |= LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB;
-	locomo_writel(r, lchip->base + LOCOMO_DAC);
-
-	r = locomo_readl(lchip->base + LOCOMO_VER);
-	printk(KERN_INFO "LoCoMo Chip: %lu%lu\n", (r >> 8), (r & 0xff));
-
-	/*
-	 * The interrupt controller must be initialised before any
-	 * other device to ensure that the interrupts are available.
-	 */
-	if (lchip->irq != NO_IRQ && lchip->irq_base != NO_IRQ)
-		locomo_setup_irq(lchip);
-
-	for (i = 0; i < ARRAY_SIZE(locomo_devices); i++)
-		locomo_init_one_child(lchip, &locomo_devices[i]);
-	return 0;
-
- out:
-	kfree(lchip);
-	return ret;
-}
-
-static int locomo_remove_child(struct device *dev, void *data)
-{
-	device_unregister(dev);
-	return 0;
-} 
-
-static void __locomo_remove(struct locomo *lchip)
-{
-	device_for_each_child(lchip->dev, NULL, locomo_remove_child);
-
-	if (lchip->irq != NO_IRQ) {
-		irq_set_chained_handler(lchip->irq, NULL);
-		irq_set_handler_data(lchip->irq, NULL);
-	}
-
-	iounmap(lchip->base);
-	kfree(lchip);
-}
-
-static int locomo_probe(struct platform_device *dev)
-{
-	struct resource *mem;
-	int irq;
-
-	mem = platform_get_resource(dev, IORESOURCE_MEM, 0);
-	if (!mem)
-		return -EINVAL;
-	irq = platform_get_irq(dev, 0);
-	if (irq < 0)
-		return -ENXIO;
-
-	return __locomo_probe(&dev->dev, mem, irq);
-}
-
-static int locomo_remove(struct platform_device *dev)
-{
-	struct locomo *lchip = platform_get_drvdata(dev);
-
-	if (lchip) {
-		__locomo_remove(lchip);
-		platform_set_drvdata(dev, NULL);
-	}
-
-	return 0;
-}
-
-/*
- *	Not sure if this should be on the system bus or not yet.
- *	We really want some way to register a system device at
- *	the per-machine level, and then have this driver pick
- *	up the registered devices.
- */
-static struct platform_driver locomo_device_driver = {
-	.probe		= locomo_probe,
-	.remove		= locomo_remove,
-#ifdef CONFIG_PM
-	.suspend	= locomo_suspend,
-	.resume		= locomo_resume,
-#endif
-	.driver		= {
-		.name	= "locomo",
-	},
-};
-
-/*
- *	Get the parent device driver (us) structure
- *	from a child function device
- */
-static inline struct locomo *locomo_chip_driver(struct locomo_dev *ldev)
-{
-	return (struct locomo *)dev_get_drvdata(ldev->dev.parent);
-}
-
-void locomo_gpio_set_dir(struct device *dev, unsigned int bits, unsigned int dir)
-{
-	struct locomo *lchip = dev_get_drvdata(dev);
-	unsigned long flags;
-	unsigned int r;
-
-	if (!lchip)
-		return;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-
-	r = locomo_readl(lchip->base + LOCOMO_GPD);
-	if (dir)
-		r |= bits;
-	else
-		r &= ~bits;
-	locomo_writel(r, lchip->base + LOCOMO_GPD);
-
-	r = locomo_readl(lchip->base + LOCOMO_GPE);
-	if (dir)
-		r |= bits;
-	else
-		r &= ~bits;
-	locomo_writel(r, lchip->base + LOCOMO_GPE);
-
-	spin_unlock_irqrestore(&lchip->lock, flags);
-}
-EXPORT_SYMBOL(locomo_gpio_set_dir);
-
-int locomo_gpio_read_level(struct device *dev, unsigned int bits)
-{
-	struct locomo *lchip = dev_get_drvdata(dev);
-	unsigned long flags;
-	unsigned int ret;
-
-	if (!lchip)
-		return -ENODEV;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-	ret = locomo_readl(lchip->base + LOCOMO_GPL);
-	spin_unlock_irqrestore(&lchip->lock, flags);
-
-	ret &= bits;
-	return ret;
-}
-EXPORT_SYMBOL(locomo_gpio_read_level);
-
-int locomo_gpio_read_output(struct device *dev, unsigned int bits)
-{
-	struct locomo *lchip = dev_get_drvdata(dev);
-	unsigned long flags;
-	unsigned int ret;
-
-	if (!lchip)
-		return -ENODEV;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-	ret = locomo_readl(lchip->base + LOCOMO_GPO);
-	spin_unlock_irqrestore(&lchip->lock, flags);
-
-	ret &= bits;
-	return ret;
-}
-EXPORT_SYMBOL(locomo_gpio_read_output);
-
-void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set)
-{
-	struct locomo *lchip = dev_get_drvdata(dev);
-	unsigned long flags;
-	unsigned int r;
-
-	if (!lchip)
-		return;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-
-	r = locomo_readl(lchip->base + LOCOMO_GPO);
-	if (set)
-		r |= bits;
-	else
-		r &= ~bits;
-	locomo_writel(r, lchip->base + LOCOMO_GPO);
-
-	spin_unlock_irqrestore(&lchip->lock, flags);
-}
-EXPORT_SYMBOL(locomo_gpio_write);
-
-static void locomo_m62332_sendbit(void *mapbase, int bit)
-{
-	unsigned int r;
-
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_DATA_HOLD_TIME);	/* 300 nsec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-
-	if (bit & 1) {
-		r = locomo_readl(mapbase + LOCOMO_DAC);
-		r |=  LOCOMO_DAC_SDAOEB;
-		locomo_writel(r, mapbase + LOCOMO_DAC);
-		udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	} else {
-		r = locomo_readl(mapbase + LOCOMO_DAC);
-		r &=  ~(LOCOMO_DAC_SDAOEB);
-		locomo_writel(r, mapbase + LOCOMO_DAC);
-		udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	}
-
-	udelay(DAC_DATA_SETUP_TIME);	/* 250 nsec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/*  4.0 usec */
-}
-
-void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel)
-{
-	struct locomo *lchip = locomo_chip_driver(ldev);
-	int i;
-	unsigned char data;
-	unsigned int r;
-	void *mapbase = lchip->base;
-	unsigned long flags;
-
-	spin_lock_irqsave(&lchip->lock, flags);
-
-	/* Start */
-	udelay(DAC_BUS_FREE_TIME);	/* 5.0 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4.0 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SDAOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_START_HOLD_TIME);	/* 5.0 usec */
-	udelay(DAC_DATA_HOLD_TIME);	/* 300 nsec */
-
-	/* Send slave address and W bit (LSB is W bit) */
-	data = (M62332_SLAVE_ADDR << 1) | M62332_W_BIT;
-	for (i = 1; i <= 8; i++) {
-		locomo_m62332_sendbit(mapbase, data >> (8 - i));
-	}
-
-	/* Check A bit */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SDAOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4.7 usec */
-	if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) {	/* High is error */
-		printk(KERN_WARNING "locomo: m62332_senddata Error 1\n");
-		goto out;
-	}
-
-	/* Send Sub address (LSB is channel select) */
-	/*    channel = 0 : ch1 select              */
-	/*            = 1 : ch2 select              */
-	data = M62332_SUB_ADDR + channel;
-	for (i = 1; i <= 8; i++) {
-		locomo_m62332_sendbit(mapbase, data >> (8 - i));
-	}
-
-	/* Check A bit */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SDAOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4.7 usec */
-	if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) {	/* High is error */
-		printk(KERN_WARNING "locomo: m62332_senddata Error 2\n");
-		goto out;
-	}
-
-	/* Send DAC data */
-	for (i = 1; i <= 8; i++) {
-		locomo_m62332_sendbit(mapbase, dac_data >> (8 - i));
-	}
-
-	/* Check A bit */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SDAOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4.7 usec */
-	if (locomo_readl(mapbase + LOCOMO_DAC) & LOCOMO_DAC_SDAOEB) {	/* High is error */
-		printk(KERN_WARNING "locomo: m62332_senddata Error 3\n");
-	}
-
-out:
-	/* stop */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r &=  ~(LOCOMO_DAC_SCLOEB);
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 300 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4 usec */
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SDAOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_HIGH_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_HIGH_HOLD_TIME);	/* 4 usec */
-
-	r = locomo_readl(mapbase + LOCOMO_DAC);
-	r |=  LOCOMO_DAC_SCLOEB | LOCOMO_DAC_SDAOEB;
-	locomo_writel(r, mapbase + LOCOMO_DAC);
-	udelay(DAC_LOW_SETUP_TIME);	/* 1000 nsec */
-	udelay(DAC_SCL_LOW_HOLD_TIME);	/* 4.7 usec */
-
-	spin_unlock_irqrestore(&lchip->lock, flags);
-}
-EXPORT_SYMBOL(locomo_m62332_senddata);
-
-/*
- *	Frontlight control
- */
-
-void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf)
-{
-	unsigned long flags;
-	struct locomo *lchip = locomo_chip_driver(dev);
-
-	if (vr)
-		locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 1);
-	else
-		locomo_gpio_write(dev->dev.parent, LOCOMO_GPIO_FL_VR, 0);
-
-	spin_lock_irqsave(&lchip->lock, flags);
-	locomo_writel(bpwf, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
-	udelay(100);
-	locomo_writel(duty, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALD);
-	locomo_writel(bpwf | LOCOMO_ALC_EN, lchip->base + LOCOMO_FRONTLIGHT + LOCOMO_ALS);
-	spin_unlock_irqrestore(&lchip->lock, flags);
-}
-EXPORT_SYMBOL(locomo_frontlight_set);
-
-/*
- *	LoCoMo "Register Access Bus."
- *
- *	We model this as a regular bus type, and hang devices directly
- *	off this.
- */
-static int locomo_match(struct device *_dev, struct device_driver *_drv)
-{
-	struct locomo_dev *dev = LOCOMO_DEV(_dev);
-	struct locomo_driver *drv = LOCOMO_DRV(_drv);
-
-	return dev->devid == drv->devid;
-}
-
-static int locomo_bus_suspend(struct device *dev, pm_message_t state)
-{
-	struct locomo_dev *ldev = LOCOMO_DEV(dev);
-	struct locomo_driver *drv = LOCOMO_DRV(dev->driver);
-	int ret = 0;
-
-	if (drv && drv->suspend)
-		ret = drv->suspend(ldev, state);
-	return ret;
-}
-
-static int locomo_bus_resume(struct device *dev)
-{
-	struct locomo_dev *ldev = LOCOMO_DEV(dev);
-	struct locomo_driver *drv = LOCOMO_DRV(dev->driver);
-	int ret = 0;
-
-	if (drv && drv->resume)
-		ret = drv->resume(ldev);
-	return ret;
-}
-
-static int locomo_bus_probe(struct device *dev)
-{
-	struct locomo_dev *ldev = LOCOMO_DEV(dev);
-	struct locomo_driver *drv = LOCOMO_DRV(dev->driver);
-	int ret = -ENODEV;
-
-	if (drv->probe)
-		ret = drv->probe(ldev);
-	return ret;
-}
-
-static int locomo_bus_remove(struct device *dev)
-{
-	struct locomo_dev *ldev = LOCOMO_DEV(dev);
-	struct locomo_driver *drv = LOCOMO_DRV(dev->driver);
-	int ret = 0;
-
-	if (drv->remove)
-		ret = drv->remove(ldev);
-	return ret;
-}
-
-struct bus_type locomo_bus_type = {
-	.name		= "locomo-bus",
-	.match		= locomo_match,
-	.probe		= locomo_bus_probe,
-	.remove		= locomo_bus_remove,
-	.suspend	= locomo_bus_suspend,
-	.resume		= locomo_bus_resume,
-};
-
-int locomo_driver_register(struct locomo_driver *driver)
-{
-	driver->drv.bus = &locomo_bus_type;
-	return driver_register(&driver->drv);
-}
-EXPORT_SYMBOL(locomo_driver_register);
-
-void locomo_driver_unregister(struct locomo_driver *driver)
-{
-	driver_unregister(&driver->drv);
-}
-EXPORT_SYMBOL(locomo_driver_unregister);
-
-static int __init locomo_init(void)
-{
-	int ret = bus_register(&locomo_bus_type);
-	if (ret == 0)
-		platform_driver_register(&locomo_device_driver);
-	return ret;
-}
-
-static void __exit locomo_exit(void)
-{
-	platform_driver_unregister(&locomo_device_driver);
-	bus_unregister(&locomo_bus_type);
-}
-
-module_init(locomo_init);
-module_exit(locomo_exit);
-
-MODULE_DESCRIPTION("Sharp LoCoMo core driver");
-MODULE_LICENSE("GPL");
-MODULE_AUTHOR("John Lenz <lenz@cs.wisc.edu>");
diff --git a/arch/arm/include/asm/hardware/locomo.h b/arch/arm/include/asm/hardware/locomo.h
deleted file mode 100644
index 74e51d6b..0000000
--- a/arch/arm/include/asm/hardware/locomo.h
+++ /dev/null
@@ -1,221 +0,0 @@
-/*
- * arch/arm/include/asm/hardware/locomo.h
- *
- * This file contains the definitions for the LoCoMo G/A Chip
- *
- * (C) Copyright 2004 John Lenz
- *
- * May be copied or modified under the terms of the GNU General Public
- * License.  See linux/COPYING for more information.
- *
- * Based on sa1111.h
- */
-#ifndef _ASM_ARCH_LOCOMO
-#define _ASM_ARCH_LOCOMO
-
-#define locomo_writel(val,addr)	({ *(volatile u16 *)(addr) = (val); })
-#define locomo_readl(addr)	(*(volatile u16 *)(addr))
-
-/* LOCOMO version */
-#define LOCOMO_VER	0x00
-
-/* Pin status */
-#define LOCOMO_ST	0x04
-
-/* Pin status */
-#define LOCOMO_C32K	0x08
-
-/* Interrupt controller */
-#define LOCOMO_ICR	0x0C
-
-/* MCS decoder for boot selecting */
-#define LOCOMO_MCSX0	0x10
-#define LOCOMO_MCSX1	0x14
-#define LOCOMO_MCSX2	0x18
-#define LOCOMO_MCSX3	0x1c
-
-/* Touch panel controller */
-#define LOCOMO_ASD	0x20		/* AD start delay */
-#define LOCOMO_HSD	0x28		/* HSYS delay */
-#define LOCOMO_HSC	0x2c		/* HSYS period */
-#define LOCOMO_TADC	0x30		/* tablet ADC clock */
-
-
-/* Long time timer */
-#define LOCOMO_LTC	0xd8		/* LTC interrupt setting */
-#define LOCOMO_LTINT	0xdc		/* LTC interrupt */
-
-/* DAC control signal for LCD (COMADJ ) */
-#define LOCOMO_DAC		0xe0
-/* DAC control */
-#define	LOCOMO_DAC_SCLOEB	0x08	/* SCL pin output data       */
-#define	LOCOMO_DAC_TEST		0x04	/* Test bit                  */
-#define	LOCOMO_DAC_SDA		0x02	/* SDA pin level (read-only) */
-#define	LOCOMO_DAC_SDAOEB	0x01	/* SDA pin output data       */
-
-/* SPI interface */
-#define LOCOMO_SPI	0x60
-#define LOCOMO_SPIMD	0x00		/* SPI mode setting */
-#define LOCOMO_SPICT	0x04		/* SPI mode control */
-#define LOCOMO_SPIST	0x08		/* SPI status */
-#define	LOCOMO_SPI_TEND	(1 << 3)	/* Transfer end bit */
-#define	LOCOMO_SPI_REND	(1 << 2)	/* Receive end bit */
-#define	LOCOMO_SPI_RFW	(1 << 1)	/* write buffer bit */
-#define	LOCOMO_SPI_RFR	(1)		/* read buffer bit */
-
-#define LOCOMO_SPIIS	0x10		/* SPI interrupt status */
-#define LOCOMO_SPIWE	0x14		/* SPI interrupt status write enable */
-#define LOCOMO_SPIIE	0x18		/* SPI interrupt enable */
-#define LOCOMO_SPIIR	0x1c		/* SPI interrupt request */
-#define LOCOMO_SPITD	0x20		/* SPI transfer data write */
-#define LOCOMO_SPIRD	0x24		/* SPI receive data read */
-#define LOCOMO_SPITS	0x28		/* SPI transfer data shift */
-#define LOCOMO_SPIRS	0x2C		/* SPI receive data shift */
-
-/* GPIO */
-#define LOCOMO_GPD		0x90	/* GPIO direction */
-#define LOCOMO_GPE		0x94	/* GPIO input enable */
-#define LOCOMO_GPL		0x98	/* GPIO level */
-#define LOCOMO_GPO		0x9c	/* GPIO out data setting */
-#define LOCOMO_GRIE		0xa0	/* GPIO rise detection */
-#define LOCOMO_GFIE		0xa4	/* GPIO fall detection */
-#define LOCOMO_GIS		0xa8	/* GPIO edge detection status */
-#define LOCOMO_GWE		0xac	/* GPIO status write enable */
-#define LOCOMO_GIE		0xb0	/* GPIO interrupt enable */
-#define LOCOMO_GIR		0xb4	/* GPIO interrupt request */
-#define	LOCOMO_GPIO(Nb)		(0x01 << (Nb))
-#define LOCOMO_GPIO_RTS		LOCOMO_GPIO(0)
-#define LOCOMO_GPIO_CTS		LOCOMO_GPIO(1)
-#define LOCOMO_GPIO_DSR		LOCOMO_GPIO(2)
-#define LOCOMO_GPIO_DTR		LOCOMO_GPIO(3)
-#define LOCOMO_GPIO_LCD_VSHA_ON	LOCOMO_GPIO(4)
-#define LOCOMO_GPIO_LCD_VSHD_ON	LOCOMO_GPIO(5)
-#define LOCOMO_GPIO_LCD_VEE_ON	LOCOMO_GPIO(6)
-#define LOCOMO_GPIO_LCD_MOD	LOCOMO_GPIO(7)
-#define LOCOMO_GPIO_DAC_ON	LOCOMO_GPIO(8)
-#define LOCOMO_GPIO_FL_VR	LOCOMO_GPIO(9)
-#define LOCOMO_GPIO_DAC_SDATA	LOCOMO_GPIO(10)
-#define LOCOMO_GPIO_DAC_SCK	LOCOMO_GPIO(11)
-#define LOCOMO_GPIO_DAC_SLOAD	LOCOMO_GPIO(12)
-#define LOCOMO_GPIO_CARD_DETECT LOCOMO_GPIO(13)
-#define LOCOMO_GPIO_WRITE_PROT  LOCOMO_GPIO(14)
-#define LOCOMO_GPIO_CARD_POWER  LOCOMO_GPIO(15)
-
-/* Start the definitions of the devices.  Each device has an initial
- * base address and a series of offsets from that base address. */
-
-/* Keyboard controller */
-#define LOCOMO_KEYBOARD		0x40
-#define LOCOMO_KIB		0x00	/* KIB level */
-#define LOCOMO_KSC		0x04	/* KSTRB control */
-#define LOCOMO_KCMD		0x08	/* KSTRB command */
-#define LOCOMO_KIC		0x0c	/* Key interrupt */
-
-/* Front light adjustment controller */
-#define LOCOMO_FRONTLIGHT	0xc8
-#define LOCOMO_ALS		0x00	/* Adjust light cycle */
-#define LOCOMO_ALD		0x04	/* Adjust light duty */
-
-#define LOCOMO_ALC_EN		0x8000
-
-/* Backlight controller: TFT signal */
-#define LOCOMO_BACKLIGHT	0x38
-#define LOCOMO_TC		0x00		/* TFT control signal */
-#define LOCOMO_CPSD		0x04		/* CPS delay */
-
-/* Audio controller */
-#define LOCOMO_AUDIO		0x54
-#define LOCOMO_ACC		0x00	/* Audio clock */
-#define LOCOMO_PAIF		0xD0	/* PCM audio interface */
-/* Audio clock */
-#define	LOCOMO_ACC_XON		0x80
-#define	LOCOMO_ACC_XEN		0x40
-#define	LOCOMO_ACC_XSEL0	0x00
-#define	LOCOMO_ACC_XSEL1	0x20
-#define	LOCOMO_ACC_MCLKEN	0x10
-#define	LOCOMO_ACC_64FSEN	0x08
-#define	LOCOMO_ACC_CLKSEL000	0x00	/* mclk  2 */
-#define	LOCOMO_ACC_CLKSEL001	0x01	/* mclk  3 */
-#define	LOCOMO_ACC_CLKSEL010	0x02	/* mclk  4 */
-#define	LOCOMO_ACC_CLKSEL011	0x03	/* mclk  6 */
-#define	LOCOMO_ACC_CLKSEL100	0x04	/* mclk  8 */
-#define	LOCOMO_ACC_CLKSEL101	0x05	/* mclk 12 */
-/* PCM audio interface */
-#define	LOCOMO_PAIF_SCINV	0x20
-#define	LOCOMO_PAIF_SCEN	0x10
-#define	LOCOMO_PAIF_LRCRST	0x08
-#define	LOCOMO_PAIF_LRCEVE	0x04
-#define	LOCOMO_PAIF_LRCINV	0x02
-#define	LOCOMO_PAIF_LRCEN	0x01
-
-/* LED controller */
-#define LOCOMO_LED		0xe8
-#define LOCOMO_LPT0		0x00
-#define LOCOMO_LPT1		0x04
-/* LED control */
-#define LOCOMO_LPT_TOFH		0x80
-#define LOCOMO_LPT_TOFL		0x08
-#define LOCOMO_LPT_TOH(TOH)	((TOH & 0x7) << 4)
-#define LOCOMO_LPT_TOL(TOL)	((TOL & 0x7))
-
-extern struct bus_type locomo_bus_type;
-
-#define LOCOMO_DEVID_KEYBOARD	0
-#define LOCOMO_DEVID_FRONTLIGHT	1
-#define LOCOMO_DEVID_BACKLIGHT	2
-#define LOCOMO_DEVID_AUDIO	3
-#define LOCOMO_DEVID_LED	4
-#define LOCOMO_DEVID_UART	5
-#define LOCOMO_DEVID_SPI	6
-
-struct locomo_dev {
-	struct device	dev;
-	unsigned int	devid;
-	unsigned int	irq[1];
-
-	void		*mapbase;
-	unsigned long	length;
-
-	u64		dma_mask;
-};
-
-#define LOCOMO_DEV(_d)	container_of((_d), struct locomo_dev, dev)
-
-#define locomo_get_drvdata(d)	dev_get_drvdata(&(d)->dev)
-#define locomo_set_drvdata(d,p)	dev_set_drvdata(&(d)->dev, p)
-
-struct locomo_driver {
-	struct device_driver	drv;
-	unsigned int		devid;
-	int (*probe)(struct locomo_dev *);
-	int (*remove)(struct locomo_dev *);
-	int (*suspend)(struct locomo_dev *, pm_message_t);
-	int (*resume)(struct locomo_dev *);
-};
-
-#define LOCOMO_DRV(_d)	container_of((_d), struct locomo_driver, drv)
-
-#define LOCOMO_DRIVER_NAME(_ldev) ((_ldev)->dev.driver->name)
-
-void locomo_lcd_power(struct locomo_dev *, int, unsigned int);
-
-int locomo_driver_register(struct locomo_driver *);
-void locomo_driver_unregister(struct locomo_driver *);
-
-/* GPIO control functions */
-void locomo_gpio_set_dir(struct device *dev, unsigned int bits, unsigned int dir);
-int locomo_gpio_read_level(struct device *dev, unsigned int bits);
-int locomo_gpio_read_output(struct device *dev, unsigned int bits);
-void locomo_gpio_write(struct device *dev, unsigned int bits, unsigned int set);
-
-/* M62332 control function */
-void locomo_m62332_senddata(struct locomo_dev *ldev, unsigned int dac_data, int channel);
-
-/* Frontlight control */
-void locomo_frontlight_set(struct locomo_dev *dev, int duty, int vr, int bpwf);
-
-struct locomo_platform_data {
-	int	irq_base;	/* IRQ base for cascaded on-chip IRQs */
-};
-
-#endif
