diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 72b0590..4406a85 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -610,6 +610,12 @@ config SPI_XTENSA_XTFPGA
 	  16 bit words in SPI mode 0, automatically asserting CS on transfer
 	  start and deasserting on end.

+config SPI_ZYNQMP_GQSPI
+	tristate "Xilinx ZynqMP GQSPI controller"
+	depends on SPI_MASTER
+	help
+	  Enables Xilinx GQSPI controller driver for Zynq UltraScale+ MPSoC.
+
 config SPI_NUC900
 	tristate "Nuvoton NUC900 series SPI"
 	depends on ARCH_W90X900
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index d8cbf65..52db832 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -89,3 +89,4 @@ obj-$(CONFIG_SPI_TXX9)			+= spi-txx9.o
 obj-$(CONFIG_SPI_XCOMM)		+= spi-xcomm.o
 obj-$(CONFIG_SPI_XILINX)		+= spi-xilinx.o
 obj-$(CONFIG_SPI_XTENSA_XTFPGA)		+= spi-xtensa-xtfpga.o
+obj-$(CONFIG_SPI_ZYNQMP_GQSPI)		+= spi-zynqmp-gqspi.o
diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
new file mode 100755
index 0000000..87b20a5
--- /dev/null
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -0,0 +1,1122 @@
+/*
+ * Xilinx Zynq UltraScale+ MPSoC Quad-SPI (QSPI) controller driver
+ * (master mode only)
+ *
+ * Copyright (C) 2009 - 2015 Xilinx, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_irq.h>
+#include <linux/of_address.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spinlock.h>
+#include <linux/workqueue.h>
+
+/* Generic QSPI register offsets */
+#define GQSPI_CONFIG_OFST		0x00000100
+#define GQSPI_ISR_OFST			0x00000104
+#define GQSPI_IDR_OFST			0x0000010C
+#define GQSPI_IER_OFST			0x00000108
+#define GQSPI_IMASK_OFST		0x00000110
+#define GQSPI_EN_OFST			0x00000114
+#define GQSPI_TXD_OFST			0x0000011C
+#define GQSPI_RXD_OFST			0x00000120
+#define GQSPI_TX_THRESHOLD_OFST		0x00000128
+#define GQSPI_RX_THRESHOLD_OFST		0x0000012C
+#define GQSPI_LPBK_DLY_ADJ_OFST		0x00000138
+#define GQSPI_GEN_FIFO_OFST		0x00000140
+#define GQSPI_SEL_OFST			0x00000144
+#define GQSPI_GF_THRESHOLD_OFST		0x00000150
+#define GQSPI_FIFO_CTRL_OFST		0x0000014C
+#define GQSPI_QSPIDMA_DST_CTRL_OFST	0x0000080C
+#define GQSPI_QSPIDMA_DST_SIZE_OFST	0x00000804
+#define GQSPI_QSPIDMA_DST_STS_OFST	0x00000808
+#define GQSPI_QSPIDMA_DST_I_STS_OFST	0x00000814
+#define GQSPI_QSPIDMA_DST_I_EN_OFST	0x00000818
+#define GQSPI_QSPIDMA_DST_I_DIS_OFST	0x0000081C
+#define GQSPI_QSPIDMA_DST_I_MASK_OFST	0x00000820
+#define GQSPI_QSPIDMA_DST_ADDR_OFST	0x00000800
+#define GQSPI_QSPIDMA_DST_ADDR_MSB_OFST 0x00000828
+
+/* GQSPI register bit masks */
+#define GQSPI_SEL_MASK				0x00000001
+#define GQSPI_EN_MASK				0x00000001
+#define GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK	0x00000020
+#define GQSPI_ISR_WR_TO_CLR_MASK		0x00000002
+#define GQSPI_IDR_ALL_MASK			0x00000FBE
+#define GQSPI_CFG_MODE_EN_MASK			0xC0000000
+#define GQSPI_CFG_GEN_FIFO_START_MODE_MASK	0x20000000
+#define GQSPI_CFG_ENDIAN_MASK			0x04000000
+#define GQSPI_CFG_EN_POLL_TO_MASK		0x00100000
+#define GQSPI_CFG_WP_HOLD_MASK			0x00080000
+#define GQSPI_CFG_BAUD_RATE_DIV_MASK		0x00000038
+#define GQSPI_CFG_CLK_PHA_MASK			0x00000004
+#define GQSPI_CFG_CLK_POL_MASK			0x00000002
+#define GQSPI_CFG_START_GEN_FIFO_MASK		0x10000000
+#define GQSPI_GENFIFO_IMM_DATA_MASK		0x000000FF
+#define GQSPI_GENFIFO_DATA_XFER			0x00000100
+#define GQSPI_GENFIFO_EXP			0x00000200
+#define GQSPI_GENFIFO_MODE_SPI			0x00000400
+#define GQSPI_GENFIFO_MODE_DUALSPI		0x00000800
+#define GQSPI_GENFIFO_MODE_QUADSPI		0x00000C00
+#define GQSPI_GENFIFO_MODE_MASK			0x00000C00
+#define GQSPI_GENFIFO_CS_LOWER			0x00001000
+#define GQSPI_GENFIFO_CS_UPPER			0x00002000
+#define GQSPI_GENFIFO_BUS_LOWER			0x00004000
+#define GQSPI_GENFIFO_BUS_UPPER			0x00008000
+#define GQSPI_GENFIFO_BUS_BOTH			0x0000C000
+#define GQSPI_GENFIFO_BUS_MASK			0x0000C000
+#define GQSPI_GENFIFO_TX			0x00010000
+#define GQSPI_GENFIFO_RX			0x00020000
+#define GQSPI_GENFIFO_STRIPE			0x00040000
+#define GQSPI_GENFIFO_POLL			0x00080000
+#define GQSPI_GENFIFO_EXP_START			0x00000100
+#define GQSPI_FIFO_CTRL_RST_RX_FIFO_MASK	0x00000004
+#define GQSPI_FIFO_CTRL_RST_TX_FIFO_MASK	0x00000002
+#define GQSPI_FIFO_CTRL_RST_GEN_FIFO_MASK	0x00000001
+#define GQSPI_ISR_RXEMPTY_MASK			0x00000800
+#define GQSPI_ISR_GENFIFOFULL_MASK		0x00000400
+#define GQSPI_ISR_GENFIFONOT_FULL_MASK		0x00000200
+#define GQSPI_ISR_TXEMPTY_MASK			0x00000100
+#define GQSPI_ISR_GENFIFOEMPTY_MASK		0x00000080
+#define GQSPI_ISR_RXFULL_MASK			0x00000020
+#define GQSPI_ISR_RXNEMPTY_MASK			0x00000010
+#define GQSPI_ISR_TXFULL_MASK			0x00000008
+#define GQSPI_ISR_TXNOT_FULL_MASK		0x00000004
+#define GQSPI_ISR_POLL_TIME_EXPIRE_MASK		0x00000002
+#define GQSPI_IER_TXNOT_FULL_MASK		0x00000004
+#define GQSPI_IER_RXEMPTY_MASK			0x00000800
+#define GQSPI_IER_POLL_TIME_EXPIRE_MASK		0x00000002
+#define GQSPI_IER_RXNEMPTY_MASK			0x00000010
+#define GQSPI_IER_GENFIFOEMPTY_MASK		0x00000080
+#define GQSPI_IER_TXEMPTY_MASK			0x00000100
+#define GQSPI_QSPIDMA_DST_INTR_ALL_MASK		0x000000FE
+#define GQSPI_QSPIDMA_DST_STS_WTC		0x0000E000
+#define GQSPI_CFG_MODE_EN_DMA_MASK		0x80000000
+#define GQSPI_ISR_IDR_MASK			0x00000994
+#define GQSPI_QSPIDMA_DST_I_EN_DONE_MASK	0x00000002
+#define GQSPI_QSPIDMA_DST_I_STS_DONE_MASK	0x00000002
+#define GQSPI_IRQ_MASK				0x00000980
+
+#define GQSPI_CFG_BAUD_RATE_DIV_SHIFT		3
+#define GQSPI_GENFIFO_CS_SETUP			0x4
+#define GQSPI_GENFIFO_CS_HOLD			0x3
+#define GQSPI_TXD_DEPTH				64
+#define GQSPI_RX_FIFO_THRESHOLD			32
+#define GQSPI_RX_FIFO_FILL	(GQSPI_RX_FIFO_THRESHOLD * 4)
+#define GQSPI_TX_FIFO_THRESHOLD_RESET_VAL	32
+#define GQSPI_TX_FIFO_FILL	(GQSPI_TXD_DEPTH -\
+				GQSPI_TX_FIFO_THRESHOLD_RESET_VAL)
+#define GQSPI_GEN_FIFO_THRESHOLD_RESET_VAL	0X10
+#define GQSPI_QSPIDMA_DST_CTRL_RESET_VAL	0x803FFA00
+#define GQSPI_SELECT_FLASH_CS_LOWER		0x1
+#define GQSPI_SELECT_FLASH_CS_UPPER		0x2
+#define GQSPI_SELECT_FLASH_CS_BOTH		0x3
+#define GQSPI_SELECT_FLASH_BUS_LOWER		0x1
+#define GQSPI_SELECT_FLASH_BUS_UPPER		0x2
+#define GQSPI_SELECT_FLASH_BUS_BOTH		0x3
+#define GQSPI_BAUD_DIV_MAX	7	/* Baud rate divisor maximum */
+#define GQSPI_BAUD_DIV_SHIFT	2	/* Baud rate divisor shift */
+#define GQSPI_SELECT_MODE_SPI		0x1
+#define GQSPI_SELECT_MODE_DUALSPI	0x2
+#define GQSPI_SELECT_MODE_QUADSPI	0x4
+#define GQSPI_DMA_UNALIGN		0x3
+#define GQSPI_DEFAULT_NUM_CS	1	/* Default number of chip selects */
+
+enum mode_type {GQSPI_MODE_IO, GQSPI_MODE_DMA};
+
+/**
+ * struct zynqmp_qspi - Defines qspi driver instance
+ * @regs:		Virtual address of the QSPI controller registers
+ * @refclk:		Pointer to the peripheral clock
+ * @pclk:		Pointer to the APB clock
+ * @irq:		IRQ number
+ * @dev:		Pointer to struct device
+ * @txbuf:		Pointer to the TX buffer
+ * @rxbuf:		Pointer to the RX buffer
+ * @bytes_to_transfer:	Number of bytes left to transfer
+ * @bytes_to_receive:	Number of bytes left to receive
+ * @genfifocs:		Used for chip select
+ * @genfifobus:		Used to select the upper or lower bus
+ * @dma_rx_bytes:	Remaining bytes to receive by DMA mode
+ * @dma_addr:		DMA address after mapping the kernel buffer
+ * @genfifoentry:	Used for storing the genfifoentry instruction.
+ * @mode:		Defines the mode in which QSPI is operating
+ */
+struct zynqmp_qspi {
+	void __iomem *regs;
+	struct clk *refclk;
+	struct clk *pclk;
+	int irq;
+	struct device *dev;
+	const void *txbuf;
+	void *rxbuf;
+	int bytes_to_transfer;
+	int bytes_to_receive;
+	u32 genfifocs;
+	u32 genfifobus;
+	u32 dma_rx_bytes;
+	dma_addr_t dma_addr;
+	u32 genfifoentry;
+	enum mode_type mode;
+};
+
+/**
+ * zynqmp_gqspi_read:	For GQSPI controller read operation
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ * @offset:	Offset from where to read
+ */
+static u32 zynqmp_gqspi_read(struct zynqmp_qspi *xqspi, u32 offset)
+{
+	return readl_relaxed(xqspi->regs + offset);
+}
+
+/**
+ * zynqmp_gqspi_write:	For GQSPI controller write operation
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ * @offset:	Offset where to write
+ * @val:	Value to be written
+ */
+static inline void zynqmp_gqspi_write(struct zynqmp_qspi *xqspi, u32 offset,
+				      u32 val)
+{
+	writel_relaxed(val, (xqspi->regs + offset));
+}
+
+/**
+ * zynqmp_gqspi_selectslave:	For selection of slave device
+ * @instanceptr:	Pointer to the zynqmp_qspi structure
+ * @flashcs:	For chip select
+ * @flashbus:	To check which bus is selected- upper or lower
+ */
+static void zynqmp_gqspi_selectslave(struct zynqmp_qspi *instanceptr,
+				     u8 slavecs, u8 slavebus)
+{
+	/*
+	 * Bus and CS lines selected here will be updated in the instance and
+	 * used for subsequent GENFIFO entries during transfer.
+	 */
+
+	/* Choose slave select line */
+	switch (slavecs) {
+	case GQSPI_SELECT_FLASH_CS_BOTH:
+		instanceptr->genfifocs = GQSPI_GENFIFO_CS_LOWER |
+			GQSPI_GENFIFO_CS_UPPER;
+	case GQSPI_SELECT_FLASH_CS_UPPER:
+		instanceptr->genfifocs = GQSPI_GENFIFO_CS_UPPER;
+		break;
+	case GQSPI_SELECT_FLASH_CS_LOWER:
+		instanceptr->genfifocs = GQSPI_GENFIFO_CS_LOWER;
+		break;
+	default:
+		dev_warn(instanceptr->dev, "Invalid slave select\n");
+	}
+
+	/* Choose the bus */
+	switch (slavebus) {
+	case GQSPI_SELECT_FLASH_BUS_BOTH:
+		instanceptr->genfifobus = GQSPI_GENFIFO_BUS_LOWER |
+			GQSPI_GENFIFO_BUS_UPPER;
+		break;
+	case GQSPI_SELECT_FLASH_BUS_UPPER:
+		instanceptr->genfifobus = GQSPI_GENFIFO_BUS_UPPER;
+		break;
+	case GQSPI_SELECT_FLASH_BUS_LOWER:
+		instanceptr->genfifobus = GQSPI_GENFIFO_BUS_LOWER;
+		break;
+	default:
+		dev_warn(instanceptr->dev, "Invalid slave bus\n");
+	}
+}
+
+/**
+ * zynqmp_qspi_init_hw:	Initialize the hardware
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ *
+ * The default settings of the QSPI controller's configurable parameters on
+ * reset are
+ *	- Master mode
+ *	- TX threshold set to 1
+ *	- RX threshold set to 1
+ *	- Flash memory interface mode enabled
+ * This function performs the following actions
+ *	- Disable and clear all the interrupts
+ *	- Enable manual slave select
+ *	- Enable manual start
+ *	- Deselect all the chip select lines
+ *	- Set the little endian mode of TX FIFO and
+ *	- Enable the QSPI controller
+ */
+static void zynqmp_qspi_init_hw(struct zynqmp_qspi *xqspi)
+{
+	u32 config_reg;
+
+	/* Select the GQSPI mode */
+	zynqmp_gqspi_write(xqspi, GQSPI_SEL_OFST, GQSPI_SEL_MASK);
+	/* Clear and disable interrupts */
+	zynqmp_gqspi_write(xqspi, GQSPI_ISR_OFST,
+			   zynqmp_gqspi_read(xqspi, GQSPI_ISR_OFST) |
+			   GQSPI_ISR_WR_TO_CLR_MASK);
+	/* Clear the DMA STS */
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_I_STS_OFST,
+			   zynqmp_gqspi_read(xqspi,
+					     GQSPI_QSPIDMA_DST_I_STS_OFST));
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_STS_OFST,
+			   zynqmp_gqspi_read(xqspi,
+					     GQSPI_QSPIDMA_DST_STS_OFST) |
+					     GQSPI_QSPIDMA_DST_STS_WTC);
+	zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_IDR_ALL_MASK);
+	zynqmp_gqspi_write(xqspi,
+			   GQSPI_QSPIDMA_DST_I_DIS_OFST,
+			   GQSPI_QSPIDMA_DST_INTR_ALL_MASK);
+	/* Disable the GQSPI */
+	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, 0x0);
+	config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
+	config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
+	/* Manual start */
+	config_reg |= GQSPI_CFG_GEN_FIFO_START_MODE_MASK;
+	/* Little endian by default */
+	config_reg &= ~GQSPI_CFG_ENDIAN_MASK;
+	/* Disable poll time out */
+	config_reg &= ~GQSPI_CFG_EN_POLL_TO_MASK;
+	/* Set hold bit */
+	config_reg |= GQSPI_CFG_WP_HOLD_MASK;
+	/* Clear pre-scalar by default */
+	config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
+	/* CPHA 0 */
+	config_reg &= ~GQSPI_CFG_CLK_PHA_MASK;
+	/* CPOL 0 */
+	config_reg &= ~GQSPI_CFG_CLK_POL_MASK;
+	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+
+	/* Clear the TX and RX FIFO */
+	zynqmp_gqspi_write(xqspi, GQSPI_FIFO_CTRL_OFST,
+			   GQSPI_FIFO_CTRL_RST_RX_FIFO_MASK |
+			   GQSPI_FIFO_CTRL_RST_TX_FIFO_MASK |
+			   GQSPI_FIFO_CTRL_RST_GEN_FIFO_MASK);
+	/* Set by default to allow for high frequencies */
+	zynqmp_gqspi_write(xqspi, GQSPI_LPBK_DLY_ADJ_OFST,
+			   zynqmp_gqspi_read(xqspi, GQSPI_LPBK_DLY_ADJ_OFST) |
+			   GQSPI_LPBK_DLY_ADJ_USE_LPBK_MASK);
+	/* Reset thresholds */
+	zynqmp_gqspi_write(xqspi, GQSPI_TX_THRESHOLD_OFST,
+			   GQSPI_TX_FIFO_THRESHOLD_RESET_VAL);
+	zynqmp_gqspi_write(xqspi, GQSPI_RX_THRESHOLD_OFST,
+			   GQSPI_RX_FIFO_THRESHOLD);
+	zynqmp_gqspi_write(xqspi, GQSPI_GF_THRESHOLD_OFST,
+			   GQSPI_GEN_FIFO_THRESHOLD_RESET_VAL);
+	zynqmp_gqspi_selectslave(xqspi,
+				 GQSPI_SELECT_FLASH_CS_LOWER,
+				 GQSPI_SELECT_FLASH_BUS_LOWER);
+	/* Initialize DMA */
+	zynqmp_gqspi_write(xqspi,
+			GQSPI_QSPIDMA_DST_CTRL_OFST,
+			GQSPI_QSPIDMA_DST_CTRL_RESET_VAL);
+
+	/* Enable the GQSPI */
+	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, GQSPI_EN_MASK);
+}
+
+/**
+ * zynqmp_qspi_copy_read_data:	Copy data to RX buffer
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ * @data:	The variable where data is stored
+ * @size:	Number of bytes to be copied from data to RX buffer
+ */
+static void zynqmp_qspi_copy_read_data(struct zynqmp_qspi *xqspi,
+				       ulong data, u8 size)
+{
+	memcpy(xqspi->rxbuf, &data, size);
+	xqspi->rxbuf += size;
+	xqspi->bytes_to_receive -= size;
+}
+
+/**
+ * zynqmp_prepare_transfer_hardware:	Prepares hardware for transfer.
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ *
+ * This function enables SPI master controller.
+ *
+ * Return:	0 on success; error value otherwise
+ */
+static int zynqmp_prepare_transfer_hardware(struct spi_master *master)
+{
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+	int ret;
+
+	ret = clk_enable(xqspi->refclk);
+	if (ret)
+		goto clk_err;
+
+	ret = clk_enable(xqspi->pclk);
+	if (ret)
+		goto clk_err;
+
+	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, GQSPI_EN_MASK);
+	return 0;
+clk_err:
+	return ret;
+}
+
+/**
+ * zynqmp_unprepare_transfer_hardware:	Relaxes hardware after transfer
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ *
+ * This function disables the SPI master controller.
+ *
+ * Return:	Always 0
+ */
+static int zynqmp_unprepare_transfer_hardware(struct spi_master *master)
+{
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+
+	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, 0x0);
+	clk_disable(xqspi->refclk);
+	clk_disable(xqspi->pclk);
+	return 0;
+}
+
+/**
+ * zynqmp_qspi_chipselect:	Select or deselect the chip select line
+ * @qspi:	Pointer to the spi_device structure
+ * @is_high:	Select(0) or deselect (1) the chip select line
+ */
+static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
+{
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(qspi->master);
+	ulong timeout;
+	u32 genfifoentry = 0x0, statusreg;
+
+	genfifoentry |= GQSPI_GENFIFO_MODE_SPI;
+	genfifoentry |= xqspi->genfifobus;
+
+	if (!is_high) {
+		genfifoentry |= xqspi->genfifocs;
+		genfifoentry |= GQSPI_GENFIFO_CS_SETUP;
+	} else {
+		genfifoentry |= GQSPI_GENFIFO_CS_HOLD;
+	}
+
+	zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, genfifoentry);
+
+	/* Dummy generic FIFO entry */
+	zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, 0x0);
+
+	/* Manually start the generic FIFO command */
+	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
+			zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
+			GQSPI_CFG_START_GEN_FIFO_MASK);
+
+	timeout = jiffies + msecs_to_jiffies(1000);
+
+	/* Wait until the generic FIFO command is empty */
+	do {
+		statusreg = zynqmp_gqspi_read(xqspi, GQSPI_ISR_OFST);
+
+		if ((statusreg & GQSPI_ISR_GENFIFOEMPTY_MASK) &&
+			(statusreg & GQSPI_ISR_TXEMPTY_MASK))
+			break;
+		else
+			cpu_relax();
+	} while (!time_after_eq(jiffies, timeout));
+
+	if (time_after_eq(jiffies, timeout))
+		dev_err(xqspi->dev, "Chip select timed out\n");
+}
+
+/**
+ * zynqmp_qspi_setup_transfer:	Configure QSPI controller for specified
+ *				transfer
+ * @qspi:	Pointer to the spi_device structure
+ * @transfer:	Pointer to the spi_transfer structure which provides
+ *		information about next transfer setup parameters
+ *
+ * Sets the operational mode of QSPI controller for the next QSPI transfer and
+ * sets the requested clock frequency.
+ *
+ * Return:	Always 0
+ *
+ * Note:
+ *	If the requested frequency is not an exact match with what can be
+ *	obtained using the pre-scalar value, the driver sets the clock
+ *	frequency which is lower than the requested frequency (maximum lower)
+ *	for the transfer.
+ *
+ *	If the requested frequency is higher or lower than that is supported
+ *	by the QSPI controller the driver will set the highest or lowest
+ *	frequency supported by controller.
+ */
+static int zynqmp_qspi_setup_transfer(struct spi_device *qspi,
+				      struct spi_transfer *transfer)
+{
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(qspi->master);
+	ulong clk_rate;
+	u32 config_reg, req_hz, baud_rate_val = 0;
+
+	if (transfer)
+		req_hz = transfer->speed_hz;
+	else
+		req_hz = qspi->max_speed_hz;
+
+	/* Set the clock frequency */
+	/* If req_hz == 0, default to lowest speed */
+	clk_rate = clk_get_rate(xqspi->refclk);
+
+	while ((baud_rate_val < GQSPI_BAUD_DIV_MAX) &&
+	       (clk_rate /
+		(GQSPI_BAUD_DIV_SHIFT << baud_rate_val)) > req_hz)
+		baud_rate_val++;
+
+	config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
+
+	/* Set the QSPI clock phase and clock polarity */
+	config_reg &= (~GQSPI_CFG_CLK_PHA_MASK) & (~GQSPI_CFG_CLK_POL_MASK);
+
+	if (qspi->mode & SPI_CPHA)
+		config_reg |= GQSPI_CFG_CLK_PHA_MASK;
+	if (qspi->mode & SPI_CPOL)
+		config_reg |= GQSPI_CFG_CLK_POL_MASK;
+
+	config_reg &= ~GQSPI_CFG_BAUD_RATE_DIV_MASK;
+	config_reg |= (baud_rate_val << GQSPI_CFG_BAUD_RATE_DIV_SHIFT);
+	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+	return 0;
+}
+
+/**
+ * zynqmp_qspi_setup:	Configure the QSPI controller
+ * @qspi:	Pointer to the spi_device structure
+ *
+ * Sets the operational mode of QSPI controller for the next QSPI transfer,
+ * baud rate and divisor value to setup the requested qspi clock.
+ *
+ * Return:	0 on success; error value otherwise.
+ */
+static int zynqmp_qspi_setup(struct spi_device *qspi)
+{
+	if (qspi->master->busy)
+		return -EBUSY;
+	return 0;
+}
+
+/**
+ * zynqmp_qspi_filltxfifo:	Fills the TX FIFO as long as there is room in
+ *				the FIFO or the bytes required to be
+ *				transmitted.
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ * @size:	Number of bytes to be copied from TX buffer to TX FIFO
+ */
+static void zynqmp_qspi_filltxfifo(struct zynqmp_qspi *xqspi, int size)
+{
+	u32 count = 0, intermediate;
+
+	while ((xqspi->bytes_to_transfer > 0) && (count < size)) {
+		memcpy(&intermediate, xqspi->txbuf, 4);
+		zynqmp_gqspi_write(xqspi, GQSPI_TXD_OFST, intermediate);
+
+		if (xqspi->bytes_to_transfer >= 4) {
+			xqspi->txbuf += 4;
+			xqspi->bytes_to_transfer -= 4;
+		} else {
+			xqspi->txbuf += xqspi->bytes_to_transfer;
+			xqspi->bytes_to_transfer = 0;
+		}
+		count++;
+	}
+}
+
+/**
+ * zynqmp_qspi_readrxfifo:	Fills the RX FIFO as long as there is room in
+ *				the FIFO.
+ * @xqspi:	Pointer to the zynqmp_qspi structure
+ * @size:	Number of bytes to be copied from RX buffer to RX FIFO
+ */
+static void zynqmp_qspi_readrxfifo(struct zynqmp_qspi *xqspi, u32 size)
+{
+	ulong data;
+	int count = 0;
+
+	while ((count < size) && (xqspi->bytes_to_receive > 0)) {
+		if (xqspi->bytes_to_receive >= 4) {
+			(*(u32 *) xqspi->rxbuf) =
+			zynqmp_gqspi_read(xqspi, GQSPI_RXD_OFST);
+			xqspi->rxbuf += 4;
+			xqspi->bytes_to_receive -= 4;
+			count += 4;
+		} else {
+			data = zynqmp_gqspi_read(xqspi, GQSPI_RXD_OFST);
+			count += xqspi->bytes_to_receive;
+			zynqmp_qspi_copy_read_data(xqspi, data,
+						   xqspi->bytes_to_receive);
+			xqspi->bytes_to_receive = 0;
+		}
+	}
+}
+
+/**
+ * zynqmp_process_dma_irq:	Handler for DMA done interrupt of QSPI
+ *				controller
+ * @xqspi:	zynqmp_qspi instance pointer
+ *
+ * This function handles DMA interrupt only.
+ */
+static void zynqmp_process_dma_irq(struct zynqmp_qspi *xqspi)
+{
+	u32 config_reg, genfifoentry;
+
+	dma_unmap_single(xqspi->dev, xqspi->dma_addr,
+				xqspi->dma_rx_bytes, DMA_FROM_DEVICE);
+	xqspi->rxbuf += xqspi->dma_rx_bytes;
+	xqspi->bytes_to_receive -= xqspi->dma_rx_bytes;
+	xqspi->dma_rx_bytes = 0;
+
+	/* Disabling the DMA interrupts */
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_I_DIS_OFST,
+					GQSPI_QSPIDMA_DST_I_EN_DONE_MASK);
+
+	if (xqspi->bytes_to_receive > 0) {
+		/* Switch to IO mode,for remaining bytes to receive */
+		config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
+		config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
+		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+
+		/* Initiate the transfer of remaining bytes */
+		genfifoentry = xqspi->genfifoentry;
+		genfifoentry |= xqspi->bytes_to_receive;
+		zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, genfifoentry);
+
+		/* Dummy generic FIFO entry */
+		zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, 0x0);
+
+		/* Manual start */
+		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
+			(zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
+			GQSPI_CFG_START_GEN_FIFO_MASK));
+
+		/* Enable the RX interrupts for IO mode */
+		zynqmp_gqspi_write(xqspi, GQSPI_IER_OFST,
+				GQSPI_IER_GENFIFOEMPTY_MASK |
+				GQSPI_IER_RXNEMPTY_MASK |
+				GQSPI_IER_RXEMPTY_MASK);
+	}
+}
+
+/**
+ * zynqmp_qspi_irq:	Interrupt service routine of the QSPI controller
+ * @irq:	IRQ number
+ * @dev_id:	Pointer to the xqspi structure
+ *
+ * This function handles TX empty only.
+ * On TX empty interrupt this function reads the received data from RX FIFO
+ * and fills the TX FIFO if there is any data remaining to be transferred.
+ *
+ * Return:	IRQ_HANDLED when interrupt is handled
+ *		IRQ_NONE otherwise.
+ */
+static irqreturn_t zynqmp_qspi_irq(int irq, void *dev_id)
+{
+	struct spi_master *master = dev_id;
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+	int ret = IRQ_NONE;
+	u32 status, mask, dma_status = 0;
+
+	status = zynqmp_gqspi_read(xqspi, GQSPI_ISR_OFST);
+	zynqmp_gqspi_write(xqspi, GQSPI_ISR_OFST, status);
+	mask = (status & ~(zynqmp_gqspi_read(xqspi, GQSPI_IMASK_OFST)));
+
+	/* Read and clear DMA status */
+	if (xqspi->mode == GQSPI_MODE_DMA) {
+		dma_status =
+			zynqmp_gqspi_read(xqspi, GQSPI_QSPIDMA_DST_I_STS_OFST);
+		zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_I_STS_OFST,
+								dma_status);
+	}
+
+	if (mask & GQSPI_ISR_TXNOT_FULL_MASK) {
+		zynqmp_qspi_filltxfifo(xqspi, GQSPI_TX_FIFO_FILL);
+		ret = IRQ_HANDLED;
+	}
+
+	if (dma_status & GQSPI_QSPIDMA_DST_I_STS_DONE_MASK) {
+		zynqmp_process_dma_irq(xqspi);
+		ret = IRQ_HANDLED;
+	} else if (!(mask & GQSPI_IER_RXEMPTY_MASK) &&
+			(mask & GQSPI_IER_GENFIFOEMPTY_MASK)) {
+		zynqmp_qspi_readrxfifo(xqspi, GQSPI_RX_FIFO_FILL);
+		ret = IRQ_HANDLED;
+	}
+
+	if ((xqspi->bytes_to_receive == 0) && (xqspi->bytes_to_transfer == 0)
+			&& ((status & GQSPI_IRQ_MASK) == GQSPI_IRQ_MASK)) {
+		zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
+		spi_finalize_current_transfer(master);
+		ret = IRQ_HANDLED;
+	}
+	return ret;
+}
+
+/**
+ * zynqmp_qspi_selectspimode:	Selects SPI mode - x1 or x2 or x4.
+ * @xqspi:	xqspi is a pointer to the GQSPI instance
+ * @spimode:	spimode - SPI or DUAL or QUAD.
+ * Return:	Mask to set desired SPI mode in GENFIFO entry.
+ */
+static inline u32 zynqmp_qspi_selectspimode(struct zynqmp_qspi *xqspi,
+						u8 spimode)
+{
+	u32 mask = 0;
+
+	switch (spimode) {
+	case GQSPI_SELECT_MODE_DUALSPI:
+		mask = GQSPI_GENFIFO_MODE_DUALSPI;
+		break;
+	case GQSPI_SELECT_MODE_QUADSPI:
+		mask = GQSPI_GENFIFO_MODE_QUADSPI;
+		break;
+	case GQSPI_SELECT_MODE_SPI:
+		mask = GQSPI_GENFIFO_MODE_SPI;
+		break;
+	default:
+		dev_warn(xqspi->dev, "Invalid SPI mode\n");
+	}
+
+	return mask;
+}
+
+/**
+ * zynq_qspi_setuprxdma:	This function sets up the RX DMA operation
+ * @xqspi:	xqspi is a pointer to the GQSPI instance.
+ */
+static void zynq_qspi_setuprxdma(struct zynqmp_qspi *xqspi)
+{
+	u32 rx_bytes, rx_rem, config_reg;
+	dma_addr_t addr;
+	u64 dma_align =  (u64)(uintptr_t)xqspi->rxbuf;
+
+	if ((xqspi->bytes_to_receive < 8) ||
+		((dma_align & GQSPI_DMA_UNALIGN) != 0x0)) {
+		/* Setting to IO mode */
+		config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
+		config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
+		zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+		xqspi->mode = GQSPI_MODE_IO;
+		xqspi->dma_rx_bytes = 0;
+		return;
+	}
+
+	rx_rem = xqspi->bytes_to_receive % 4;
+	rx_bytes = (xqspi->bytes_to_receive - rx_rem);
+
+	addr = dma_map_single(xqspi->dev, (void *)xqspi->rxbuf,
+						rx_bytes, DMA_FROM_DEVICE);
+	if (dma_mapping_error(xqspi->dev, addr))
+		dev_err(xqspi->dev, "ERR:rxdma:memory not mapped\n");
+
+	xqspi->dma_rx_bytes = rx_bytes;
+	xqspi->dma_addr = addr;
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_ADDR_OFST,
+				(u32)(addr & 0xffffffff));
+	addr = ((addr >> 16) >> 16);
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_ADDR_MSB_OFST,
+				((u32)addr) & 0xfff);
+
+	/* Enabling the DMA mode */
+	config_reg = zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST);
+	config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
+	config_reg |= GQSPI_CFG_MODE_EN_DMA_MASK;
+	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST, config_reg);
+
+	/* Switch to DMA mode */
+	xqspi->mode = GQSPI_MODE_DMA;
+
+	/* Write the number of bytes to transfer */
+	zynqmp_gqspi_write(xqspi, GQSPI_QSPIDMA_DST_SIZE_OFST, rx_bytes);
+}
+
+/**
+ * zynqmp_qspi_txrxsetup:	This function checks the TX/RX buffers in
+ *				the transfer and sets up the GENFIFO entries,
+ *				TX FIFO as required.
+ * @xqspi:	xqspi is a pointer to the GQSPI instance.
+ * @transfer:	It is a pointer to the structure containing transfer data.
+ * @genfifoentry:	genfifoentry is pointer to the variable in which
+ *			GENFIFO	mask is returned to calling function
+ */
+static void zynqmp_qspi_txrxsetup(struct zynqmp_qspi *xqspi,
+				  struct spi_transfer *transfer,
+				  u32 *genfifoentry)
+{
+	u32 config_reg;
+
+	/* Transmit */
+	if ((xqspi->txbuf != NULL) && (xqspi->rxbuf == NULL)) {
+		/* Setup data to be TXed */
+		*genfifoentry &= ~GQSPI_GENFIFO_RX;
+		*genfifoentry |= GQSPI_GENFIFO_DATA_XFER;
+		*genfifoentry |= GQSPI_GENFIFO_TX;
+		*genfifoentry |=
+			zynqmp_qspi_selectspimode(xqspi, transfer->tx_nbits);
+		xqspi->bytes_to_transfer = transfer->len;
+		if (xqspi->mode == GQSPI_MODE_DMA) {
+			config_reg = zynqmp_gqspi_read(xqspi,
+							GQSPI_CONFIG_OFST);
+			config_reg &= ~GQSPI_CFG_MODE_EN_MASK;
+			zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
+								config_reg);
+			xqspi->mode = GQSPI_MODE_IO;
+		}
+		zynqmp_qspi_filltxfifo(xqspi, GQSPI_TXD_DEPTH);
+		/* Discard RX data */
+		xqspi->bytes_to_receive = 0;
+	} else if ((xqspi->txbuf == NULL) && (xqspi->rxbuf != NULL)) {
+		/* Receive */
+
+		/* TX auto fill */
+		*genfifoentry &= ~GQSPI_GENFIFO_TX;
+		/* Setup RX */
+		*genfifoentry |= GQSPI_GENFIFO_DATA_XFER;
+		*genfifoentry |= GQSPI_GENFIFO_RX;
+		*genfifoentry |=
+			zynqmp_qspi_selectspimode(xqspi, transfer->rx_nbits);
+		xqspi->bytes_to_transfer = 0;
+		xqspi->bytes_to_receive = transfer->len;
+		zynq_qspi_setuprxdma(xqspi);
+	}
+}
+
+/**
+ * zynqmp_qspi_start_transfer:	Initiates the QSPI transfer
+ * @master:	Pointer to the spi_master structure which provides
+ *		information about the controller.
+ * @qspi:	Pointer to the spi_device structure
+ * @transfer:	Pointer to the spi_transfer structure which provide information
+ *		about next transfer parameters
+ *
+ * This function fills the TX FIFO, starts the QSPI transfer, and waits for the
+ * transfer to be completed.
+ *
+ * Return:	Number of bytes transferred in the last transfer
+ */
+static int zynqmp_qspi_start_transfer(struct spi_master *master,
+				      struct spi_device *qspi,
+				      struct spi_transfer *transfer)
+{
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+	u32 genfifoentry = 0x0, transfer_len;
+
+	xqspi->txbuf = transfer->tx_buf;
+	xqspi->rxbuf = transfer->rx_buf;
+
+	zynqmp_qspi_setup_transfer(qspi, transfer);
+
+	genfifoentry |= xqspi->genfifocs;
+	genfifoentry |= xqspi->genfifobus;
+
+	zynqmp_qspi_txrxsetup(xqspi, transfer, &genfifoentry);
+
+	if (xqspi->mode == GQSPI_MODE_DMA)
+		transfer_len = xqspi->dma_rx_bytes;
+	else
+		transfer_len = transfer->len;
+
+	xqspi->genfifoentry = genfifoentry;
+	if ((transfer_len) < GQSPI_GENFIFO_IMM_DATA_MASK) {
+		genfifoentry &= ~GQSPI_GENFIFO_IMM_DATA_MASK;
+		genfifoentry |= transfer_len;
+		zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, genfifoentry);
+	} else {
+		int tempcount = transfer_len;
+		u32 exponent = 8;	/* 2^8 = 256 */
+		u8 imm_data = tempcount & 0xFF;
+
+		tempcount &= ~(tempcount & 0xFF);
+		/* Immediate entry */
+		if (tempcount != 0) {
+			/* Exponent entries */
+			genfifoentry |= GQSPI_GENFIFO_EXP;
+			while (tempcount != 0) {
+				if (tempcount & GQSPI_GENFIFO_EXP_START) {
+					genfifoentry &=
+					    ~GQSPI_GENFIFO_IMM_DATA_MASK;
+					genfifoentry |= exponent;
+					zynqmp_gqspi_write(xqspi,
+							   GQSPI_GEN_FIFO_OFST,
+							   genfifoentry);
+				}
+				tempcount = tempcount >> 1;
+				exponent++;
+			}
+		}
+		if (imm_data != 0) {
+			genfifoentry &= ~GQSPI_GENFIFO_EXP;
+			genfifoentry &= ~GQSPI_GENFIFO_IMM_DATA_MASK;
+			genfifoentry |= (u8) (imm_data & 0xFF);
+			zynqmp_gqspi_write(xqspi,
+					   GQSPI_GEN_FIFO_OFST, genfifoentry);
+		}
+	}
+
+	if ((xqspi->mode == GQSPI_MODE_IO) &&
+			(xqspi->rxbuf != NULL)) {
+		/* Dummy generic FIFO entry */
+		zynqmp_gqspi_write(xqspi, GQSPI_GEN_FIFO_OFST, 0x0);
+	}
+
+	/* Since we are using manual mode */
+	zynqmp_gqspi_write(xqspi, GQSPI_CONFIG_OFST,
+			   zynqmp_gqspi_read(xqspi, GQSPI_CONFIG_OFST) |
+			   GQSPI_CFG_START_GEN_FIFO_MASK);
+
+	if (xqspi->txbuf != NULL)
+		/* Enable interrupts for TX */
+		zynqmp_gqspi_write(xqspi, GQSPI_IER_OFST,
+				   GQSPI_IER_TXEMPTY_MASK |
+					GQSPI_IER_GENFIFOEMPTY_MASK |
+					GQSPI_IER_TXNOT_FULL_MASK);
+
+	if (xqspi->rxbuf != NULL) {
+		/* Enable interrupts for RX */
+		if (xqspi->mode == GQSPI_MODE_DMA) {
+			/* Enable DMA interrupts */
+			zynqmp_gqspi_write(xqspi,
+					GQSPI_QSPIDMA_DST_I_EN_OFST,
+					GQSPI_QSPIDMA_DST_I_EN_DONE_MASK);
+		} else {
+			zynqmp_gqspi_write(xqspi, GQSPI_IER_OFST,
+					GQSPI_IER_GENFIFOEMPTY_MASK |
+					GQSPI_IER_RXNEMPTY_MASK |
+					GQSPI_IER_RXEMPTY_MASK);
+		}
+	}
+
+	return transfer->len;
+}
+
+/**
+ * zynqmp_qspi_suspend:	Suspend method for the QSPI driver
+ * @_dev:	Address of the platform_device structure
+ *
+ * This function stops the QSPI driver queue and disables the QSPI controller
+ *
+ * Return:	Always 0
+ */
+static int __maybe_unused zynqmp_qspi_suspend(struct device *dev)
+{
+	struct platform_device *pdev = container_of(dev,
+						    struct platform_device,
+						    dev);
+	struct spi_master *master = platform_get_drvdata(pdev);
+
+	spi_master_suspend(master);
+
+	zynqmp_unprepare_transfer_hardware(master);
+
+	return 0;
+}
+
+/**
+ * zynqmp_qspi_resume:	Resume method for the QSPI driver
+ * @dev:	Address of the platform_device structure
+ *
+ * The function starts the QSPI driver queue and initializes the QSPI
+ * controller
+ *
+ * Return:	0 on success; error value otherwise
+ */
+static int __maybe_unused zynqmp_qspi_resume(struct device *dev)
+{
+	struct platform_device *pdev = container_of(dev,
+						    struct platform_device,
+						    dev);
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+	int ret = 0;
+
+	ret = clk_enable(xqspi->pclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable APB clock.\n");
+		return ret;
+	}
+
+	ret = clk_enable(xqspi->refclk);
+	if (ret) {
+		dev_err(dev, "Cannot enable device clock.\n");
+		clk_disable(xqspi->pclk);
+		return ret;
+	}
+
+	spi_master_resume(master);
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(zynqmp_qspi_dev_pm_ops, zynqmp_qspi_suspend,
+			 zynqmp_qspi_resume);
+
+/**
+ * zynqmp_qspi_probe:	Probe method for the QSPI driver
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * This function initializes the driver data structures and the hardware.
+ *
+ * Return:	0 on success; error value otherwise
+ */
+static int zynqmp_qspi_probe(struct platform_device *pdev)
+{
+	int ret = 0;
+	struct spi_master *master;
+	struct zynqmp_qspi *xqspi;
+	struct resource *res;
+	struct device *dev = &pdev->dev;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(*xqspi));
+	if (!master)
+		return -ENOMEM;
+
+	xqspi = spi_master_get_devdata(master);
+	master->dev.of_node = pdev->dev.of_node;
+	platform_set_drvdata(pdev, master);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	xqspi->regs = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(xqspi->regs)) {
+		ret = PTR_ERR(xqspi->regs);
+		goto remove_master;
+	}
+
+	xqspi->dev = dev;
+	xqspi->pclk = devm_clk_get(&pdev->dev, "pclk");
+	if (IS_ERR(xqspi->pclk)) {
+		dev_err(dev, "pclk clock not found.\n");
+		ret = PTR_ERR(xqspi->pclk);
+		goto remove_master;
+	}
+
+	ret = clk_prepare_enable(xqspi->pclk);
+	if (ret) {
+		dev_err(dev, "Unable to enable APB clock.\n");
+		goto remove_master;
+	}
+
+	xqspi->refclk = devm_clk_get(&pdev->dev, "ref_clk");
+	if (IS_ERR(xqspi->refclk)) {
+		dev_err(dev, "ref_clk clock not found.\n");
+		ret = PTR_ERR(xqspi->refclk);
+		goto clk_dis_pclk;
+	}
+
+	ret = clk_prepare_enable(xqspi->refclk);
+	if (ret) {
+		dev_err(dev, "Unable to enable device clock.\n");
+		goto clk_dis_pclk;
+	}
+
+	/* QSPI controller initializations */
+	zynqmp_qspi_init_hw(xqspi);
+
+	xqspi->irq = platform_get_irq(pdev, 0);
+	if (xqspi->irq <= 0) {
+		ret = -ENXIO;
+		dev_err(dev, "irq resource not found\n");
+		goto clk_dis_all;
+	}
+	ret = devm_request_irq(&pdev->dev, xqspi->irq, zynqmp_qspi_irq,
+			       0, pdev->name, master);
+	if (ret != 0) {
+		ret = -ENXIO;
+		dev_err(dev, "request_irq failed\n");
+		goto clk_dis_all;
+	}
+
+	master->num_chipselect = GQSPI_DEFAULT_NUM_CS;
+
+	master->setup = zynqmp_qspi_setup;
+	master->set_cs = zynqmp_qspi_chipselect;
+	master->transfer_one = zynqmp_qspi_start_transfer;
+	master->prepare_transfer_hardware = zynqmp_prepare_transfer_hardware;
+	master->unprepare_transfer_hardware =
+					zynqmp_unprepare_transfer_hardware;
+	master->max_speed_hz = clk_get_rate(xqspi->refclk) / 2;
+	master->bits_per_word_mask = SPI_BPW_MASK(8);
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
+			    SPI_TX_DUAL | SPI_TX_QUAD;
+
+	if (master->dev.parent == NULL)
+		master->dev.parent = &master->dev;
+
+	ret = spi_register_master(master);
+	if (ret)
+		goto clk_dis_all;
+
+	return 0;
+
+clk_dis_all:
+	clk_disable_unprepare(xqspi->refclk);
+clk_dis_pclk:
+	clk_disable_unprepare(xqspi->pclk);
+remove_master:
+	spi_master_put(master);
+
+	return ret;
+}
+
+/**
+ * zynqmp_qspi_remove:	Remove method for the QSPI driver
+ * @pdev:	Pointer to the platform_device structure
+ *
+ * This function is called if a device is physically removed from the system or
+ * if the driver module is being unloaded. It frees all resources allocated to
+ * the device.
+ *
+ * Return:	0 Always
+ */
+static int zynqmp_qspi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct zynqmp_qspi *xqspi = spi_master_get_devdata(master);
+
+	zynqmp_gqspi_write(xqspi, GQSPI_EN_OFST, 0x0);
+	clk_disable_unprepare(xqspi->refclk);
+	clk_disable_unprepare(xqspi->pclk);
+
+	spi_unregister_master(master);
+
+	return 0;
+}
+
+static const struct of_device_id zynqmp_qspi_of_match[] = {
+	{ .compatible = "xlnx,zynqmp-qspi-1.0", },
+	{ /* End of table */ }
+};
+
+MODULE_DEVICE_TABLE(of, zynqmp_qspi_of_match);
+
+static struct platform_driver zynqmp_qspi_driver = {
+	.probe = zynqmp_qspi_probe,
+	.remove = zynqmp_qspi_remove,
+	.driver = {
+		.name = "zynqmp-qspi",
+		.of_match_table = zynqmp_qspi_of_match,
+		.pm = &zynqmp_qspi_dev_pm_ops,
+	},
+};
+
+module_platform_driver(zynqmp_qspi_driver);
+
+MODULE_AUTHOR("Xilinx, Inc.");
+MODULE_DESCRIPTION("Xilinx Zynqmp QSPI driver");
+MODULE_LICENSE("GPL");
