| Message ID | 1467989201-14661-7-git-send-email-andi.shyti@samsung.com (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Quoting Andi Shyti (2016-07-08 07:46:40) > Patch a9e93e8 has erroneously removed some comments which are > important to understand why the bus frequency is multiplied by > two during the spi transfer. > > Signed-off-by: Andi Shyti <andi.shyti@samsung.com> > --- > drivers/spi/spi-s3c64xx.c | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c > index 6da663f..32b66f0 100644 > --- a/drivers/spi/spi-s3c64xx.c > +++ b/drivers/spi/spi-s3c64xx.c > @@ -639,6 +639,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) > writel(val, regs + S3C64XX_SPI_MODE_CFG); > > if (sdd->port_conf->clk_from_cmu) { > + /* There is half-multiplier before the SPI */ > clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); Just a small comment, but if the fixed-factor divide-by-two clock was modeled in Linux, then this driver could call clk_set_rate on that clock with the "correct" rate. I guess that this driver would be the provider of that clock? Regards, Mike > } else { > /* Configure Clock */ > -- > 2.8.1 > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mike, > > if (sdd->port_conf->clk_from_cmu) { > > + /* There is half-multiplier before the SPI */ > > clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); > > Just a small comment, but if the fixed-factor divide-by-two clock was > modeled in Linux, then this driver could call clk_set_rate on that clock > with the "correct" rate. > > I guess that this driver would be the provider of that clock? Makes sense, I will check it. Thanks again, Andi -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Jul 08, 2016 at 11:46:40PM +0900, Andi Shyti wrote: > Patch a9e93e8 has erroneously removed some comments which are > important to understand why the bus frequency is multiplied by > two during the spi transfer. > > Signed-off-by: Andi Shyti <andi.shyti@samsung.com> > --- > drivers/spi/spi-s3c64xx.c | 1 + > 1 file changed, 1 insertion(+) > > diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c > index 6da663f..32b66f0 100644 > --- a/drivers/spi/spi-s3c64xx.c > +++ b/drivers/spi/spi-s3c64xx.c > @@ -639,6 +639,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) > writel(val, regs + S3C64XX_SPI_MODE_CFG); > > if (sdd->port_conf->clk_from_cmu) { > + /* There is half-multiplier before the SPI */ > clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); > } else { > /* Configure Clock */ Regardless of possible followup after Michael's comments: Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Best regards, Krzysztof -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 07/08/2016 06:17 PM, Michael Turquette wrote: > Quoting Andi Shyti (2016-07-08 07:46:40) >> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c >> index 6da663f..32b66f0 100644 >> --- a/drivers/spi/spi-s3c64xx.c >> +++ b/drivers/spi/spi-s3c64xx.c >> @@ -639,6 +639,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) >> writel(val, regs + S3C64XX_SPI_MODE_CFG); >> >> if (sdd->port_conf->clk_from_cmu) { >> + /* There is half-multiplier before the SPI */ >> clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); > > Just a small comment, but if the fixed-factor divide-by-two clock was > modeled in Linux, then this driver could call clk_set_rate on that clock > with the "correct" rate. > > I guess that this driver would be the provider of that clock? Good point, however I'm not sure if it is worth to model this divider with a clk object. It is an internal divider and the clock it provides is only used internally within the SPI controller. Thus the spi-s3c64xx driver would be provider on the only consumer of this clock. Additionally, the "There is half-multiplier before the SPI" comment seems to be obfuscating how the hardware really looks like to me. It talks about multiplier (which reminds me of PLLs with a divider in the feedback loop) while there is a simple divider which should be considered as an integral part of the controller IP block. While we are at it, I'd propose to change this comment to something like: /* The SCLK_SPI clock is divided internally by 2 */ -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Quoting Sylwester Nawrocki (2016-07-11 03:33:42) > On 07/08/2016 06:17 PM, Michael Turquette wrote: > > Quoting Andi Shyti (2016-07-08 07:46:40) > > >> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c > >> index 6da663f..32b66f0 100644 > >> --- a/drivers/spi/spi-s3c64xx.c > >> +++ b/drivers/spi/spi-s3c64xx.c > >> @@ -639,6 +639,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) > >> writel(val, regs + S3C64XX_SPI_MODE_CFG); > >> > >> if (sdd->port_conf->clk_from_cmu) { > >> + /* There is half-multiplier before the SPI */ > >> clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); > > > > Just a small comment, but if the fixed-factor divide-by-two clock was > > modeled in Linux, then this driver could call clk_set_rate on that clock > > with the "correct" rate. > > > > I guess that this driver would be the provider of that clock? > > Good point, however I'm not sure if it is worth to model this divider > with a clk object. It is an internal divider and the clock it provides > is only used internally within the SPI controller. Thus the spi-s3c64xx > driver would be provider on the only consumer of this clock. Sure, but it's only a few lines of code to this, and there are examples in the kernel already. > > Additionally, the "There is half-multiplier before the SPI" comment > seems to be obfuscating how the hardware really looks like to me. > It talks about multiplier (which reminds me of PLLs with a divider > in the feedback loop) while there is a simple divider which should > be considered as an integral part of the controller IP block. > > While we are at it, I'd propose to change this comment to something > like: > > /* The SCLK_SPI clock is divided internally by 2 */ It's your choice, but debug output would benefit from showing the real clock frequency at some point. Regards, Mike -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 07/12/2016 12:17 AM, Michael Turquette wrote: > Quoting Sylwester Nawrocki (2016-07-11 03:33:42) >> On 07/08/2016 06:17 PM, Michael Turquette wrote: > Sure, but it's only a few lines of code to this, and there are examples > in the kernel already. > >> Additionally, the "There is half-multiplier before the SPI" comment >> seems to be obfuscating how the hardware really looks like to me. >> It talks about multiplier (which reminds me of PLLs with a divider >> in the feedback loop) while there is a simple divider which should >> be considered as an integral part of the controller IP block. >> >> While we are at it, I'd propose to change this comment to something >> like: >> >> /* The SCLK_SPI clock is divided internally by 2 */ > > It's your choice, but debug output would benefit from showing the real > clock frequency at some point. OK, it's indeed fairly easy to add a fixed rate divide-by-two clock, but for the older SoCs we would need to also model the internal mux, gate, and an 8-bit divider. Then it becomes a bit bigger task. Anyway it might be worth to try it, this could let us deprecate the samsung,spi-src-clk property and for all the SoCs use assigned-clock-parents.
diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index 6da663f..32b66f0 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -639,6 +639,7 @@ static void s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd) writel(val, regs + S3C64XX_SPI_MODE_CFG); if (sdd->port_conf->clk_from_cmu) { + /* There is half-multiplier before the SPI */ clk_set_rate(sdd->src_clk, sdd->cur_speed * 2); } else { /* Configure Clock */
Patch a9e93e8 has erroneously removed some comments which are important to understand why the bus frequency is multiplied by two during the spi transfer. Signed-off-by: Andi Shyti <andi.shyti@samsung.com> --- drivers/spi/spi-s3c64xx.c | 1 + 1 file changed, 1 insertion(+)