| Message ID | 20170802225717.24408-15-hauke@hauke-m.de (mailing list archive) |
|---|---|
| State | New, archived |
| Headers | show |
Hi Kishon, On 08/03/2017 12:57 AM, Hauke Mehrtens wrote: > This driver starts the DWC2 core(s) built into the XWAY SoCs and provides > the PHY interfaces for each core. The phy instances can be passed to the > dwc2 driver, which already supports the generic phy interface. > > Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> > Cc: Kishon Vijay Abraham I <kishon@ti.com> Kishon could you please review this patch and give an Ack or Nack, I would like to merge this thorough Ralf's mips tree. > --- > .../bindings/phy/phy-lantiq-rcu-usb2.txt | 43 +++ > arch/mips/lantiq/xway/sysctrl.c | 24 +- > drivers/phy/Kconfig | 1 + > drivers/phy/Makefile | 2 +- > drivers/phy/lantiq/Kconfig | 10 + > drivers/phy/lantiq/Makefile | 1 + > drivers/phy/lantiq/phy-lantiq-rcu-usb2.c | 290 +++++++++++++++++++++ > 7 files changed, 358 insertions(+), 13 deletions(-) > create mode 100644 Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > create mode 100644 drivers/phy/lantiq/Kconfig > create mode 100644 drivers/phy/lantiq/Makefile > create mode 100644 drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > > diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > new file mode 100644 > index 000000000000..76036c5c5d11 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > @@ -0,0 +1,43 @@ > +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding > +=========================================== > + > +This binding describes the USB PHY hardware provided by the RCU module on the > +Lantiq XWAY SoCs. > + > +This driver has to be a sub node of the Lantiq RCU block. > + > +------------------------------------------------------------------------------- > +Required properties (controller (parent) node): > +- compatible : Should be one of > + "lantiq,ase-usb2-phy" > + "lantiq,danube-usb2-phy" > + "lantiq,xrx100-usb2-phy" > + "lantiq,xrx200-usb2-phy" > + "lantiq,xrx300-usb2-phy" > +- reg : Defines the following sets of registers in the parent > + syscon device > + - Offset of the USB PHY configuration register > + - Offset of the USB Analog configuration > + register (only for xrx200 and xrx200) > +- clocks : References to the (PMU) "ctrl" and "phy" clk gates. > +- clock-names : Must be one of the following: > + "ctrl" > + "phy" > +- resets : References to the RCU USB configuration reset bits. > +- reset-names : Must be one of the following: > + "phy" (optional) > + "ctrl" (shared) > + > +------------------------------------------------------------------------------- > +Example for the USB PHYs on an xRX200 SoC: > + usb_phy0: usb2-phy@18 { > + compatible = "lantiq,xrx200-usb2-phy"; > + reg = <0x18 4>, <0x38 4>; > + > + clocks = <&pmu PMU_GATE_USB0_CTRL>, > + <&pmu PMU_GATE_USB0_PHY>; > + clock-names = "ctrl", "phy"; > + resets = <&reset1 4 4>, <&reset0 4 4>; > + reset-names = "phy", "ctrl"; > + #phy-cells = <0>; > + }; > diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c > index 87eab4d288e5..f76978e4da32 100644 > --- a/arch/mips/lantiq/xway/sysctrl.c > +++ b/arch/mips/lantiq/xway/sysctrl.c .... > index c1807d4a0079..968088ceaeb3 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -52,6 +52,7 @@ source "drivers/phy/allwinner/Kconfig" > source "drivers/phy/amlogic/Kconfig" > source "drivers/phy/broadcom/Kconfig" > source "drivers/phy/hisilicon/Kconfig" > +source "drivers/phy/lantiq/Kconfig" > source "drivers/phy/marvell/Kconfig" > source "drivers/phy/motorola/Kconfig" > source "drivers/phy/qualcomm/Kconfig" > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index f252201e0ec9..a8b9439a5d8e 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -7,9 +7,9 @@ obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o > obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o > obj-$(CONFIG_PHY_XGENE) += phy-xgene.o > obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o > - > obj-$(CONFIG_ARCH_SUNXI) += allwinner/ > obj-$(CONFIG_ARCH_MESON) += amlogic/ > +obj-$(CONFIG_LANTIQ) += lantiq/ > obj-$(CONFIG_ARCH_RENESAS) += renesas/ > obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ > obj-$(CONFIG_ARCH_TEGRA) += tegra/ > diff --git a/drivers/phy/lantiq/Kconfig b/drivers/phy/lantiq/Kconfig > new file mode 100644 > index 000000000000..a2d5006b3dc7 > --- /dev/null > +++ b/drivers/phy/lantiq/Kconfig > @@ -0,0 +1,10 @@ > +# > +# Phy drivers for Lantiq / Intel platforms > +# > +config PHY_LANTIQ_RCU_USB2 > + tristate "Lantiq XWAY SoC RCU based USB PHY" > + depends on SOC_TYPE_XWAY > + depends on OF > + select GENERIC_PHY > + help > + Support for the USB PHY(s) on the Lantiq / Intel XWAY family SoCs. > diff --git a/drivers/phy/lantiq/Makefile b/drivers/phy/lantiq/Makefile > new file mode 100644 > index 000000000000..f73eb56a5416 > --- /dev/null > +++ b/drivers/phy/lantiq/Makefile > @@ -0,0 +1 @@ > +obj-$(CONFIG_PHY_LANTIQ_RCU_USB2) += phy-lantiq-rcu-usb2.o > diff --git a/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > new file mode 100644 > index 000000000000..8f5687737b50 > --- /dev/null > +++ b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > @@ -0,0 +1,290 @@ ..... > + > + ret = of_address_to_resource(dev->of_node->parent, 0, &res_parent); > + if (ret) > + return ret; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!res) { > + dev_err(dev, "Failed to get RCU PHY reg offset\n"); > + return ret; I will return -ENOENT here. > + } > + > + if (res->start < res_parent.start) > + return -ENOENT; > + priv->phy_reg_offset = res->start - res_parent.start; > + > + if (priv->reg_bits->have_ana_cfg) { > + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); > + if (!res) { > + dev_err(dev, "Failed to get RCU ANA CFG1 reg offset\n"); > + return ret; I will return -ENOENT here. > + } > + > + if (res->start < res_parent.start) > + return -ENOENT; > + priv->ana_cfg1_reg_offset = res->start - res_parent.start; > + } > + -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi, On Thursday 03 August 2017 04:27 AM, Hauke Mehrtens wrote: > This driver starts the DWC2 core(s) built into the XWAY SoCs and provides > the PHY interfaces for each core. The phy instances can be passed to the > dwc2 driver, which already supports the generic phy interface. > > Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> > Cc: Kishon Vijay Abraham I <kishon@ti.com> > --- > .../bindings/phy/phy-lantiq-rcu-usb2.txt | 43 +++ > arch/mips/lantiq/xway/sysctrl.c | 24 +- > drivers/phy/Kconfig | 1 + > drivers/phy/Makefile | 2 +- > drivers/phy/lantiq/Kconfig | 10 + > drivers/phy/lantiq/Makefile | 1 + > drivers/phy/lantiq/phy-lantiq-rcu-usb2.c | 290 +++++++++++++++++++++ > 7 files changed, 358 insertions(+), 13 deletions(-) > create mode 100644 Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > create mode 100644 drivers/phy/lantiq/Kconfig > create mode 100644 drivers/phy/lantiq/Makefile > create mode 100644 drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > > diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > new file mode 100644 > index 000000000000..76036c5c5d11 > --- /dev/null > +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt > @@ -0,0 +1,43 @@ > +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding > +=========================================== > + > +This binding describes the USB PHY hardware provided by the RCU module on the > +Lantiq XWAY SoCs. > + > +This driver has to be a sub node of the Lantiq RCU block. > + > +------------------------------------------------------------------------------- > +Required properties (controller (parent) node): > +- compatible : Should be one of > + "lantiq,ase-usb2-phy" > + "lantiq,danube-usb2-phy" > + "lantiq,xrx100-usb2-phy" > + "lantiq,xrx200-usb2-phy" > + "lantiq,xrx300-usb2-phy" > +- reg : Defines the following sets of registers in the parent > + syscon device > + - Offset of the USB PHY configuration register > + - Offset of the USB Analog configuration > + register (only for xrx200 and xrx200) > +- clocks : References to the (PMU) "ctrl" and "phy" clk gates. > +- clock-names : Must be one of the following: > + "ctrl" > + "phy" > +- resets : References to the RCU USB configuration reset bits. > +- reset-names : Must be one of the following: > + "phy" (optional) > + "ctrl" (shared) > + > +------------------------------------------------------------------------------- > +Example for the USB PHYs on an xRX200 SoC: > + usb_phy0: usb2-phy@18 { > + compatible = "lantiq,xrx200-usb2-phy"; > + reg = <0x18 4>, <0x38 4>; > + > + clocks = <&pmu PMU_GATE_USB0_CTRL>, > + <&pmu PMU_GATE_USB0_PHY>; > + clock-names = "ctrl", "phy"; > + resets = <&reset1 4 4>, <&reset0 4 4>; > + reset-names = "phy", "ctrl"; > + #phy-cells = <0>; > + }; Please CC device tree list and get Ack from devicetree maintainers for this binding. Preferable send this as a separate patch. > diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c > index 87eab4d288e5..f76978e4da32 100644 > --- a/arch/mips/lantiq/xway/sysctrl.c > +++ b/arch/mips/lantiq/xway/sysctrl.c > @@ -469,8 +469,8 @@ void __init ltq_soc_init(void) > > if (of_machine_is_compatible("lantiq,grx390") || > of_machine_is_compatible("lantiq,ar10")) { > - clkdev_add_pmu("1e101000.usb", "phy", 1, 2, PMU_ANALOG_USB0_P); > - clkdev_add_pmu("1e106000.usb", "phy", 1, 2, PMU_ANALOG_USB1_P); > + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB0_P); > + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB1_P); > /* rc 0 */ > clkdev_add_pmu("1d900000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE0_P); > clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); > @@ -490,8 +490,8 @@ void __init ltq_soc_init(void) > else > clkdev_add_static(CLOCK_133M, CLOCK_133M, > CLOCK_133M, CLOCK_133M); > - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); > - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); > + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); > + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); > clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE); > clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY); > clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY); > @@ -526,10 +526,10 @@ void __init ltq_soc_init(void) > } else if (of_machine_is_compatible("lantiq,vr9")) { > clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(), > ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz()); > - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); > - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0 | PMU_AHBM); > - clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); > - clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1 | PMU_AHBM); > + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); > + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0 | PMU_AHBM); > + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 0, PMU_USB1_P); > + clkdev_add_pmu("1f203034.usb2-phy", "ctrl", 1, 0, PMU_USB1 | PMU_AHBM); > clkdev_add_pmu("1d900000.pcie", "phy", 1, 1, PMU1_PCIE_PHY); > clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK); > clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); > @@ -550,8 +550,8 @@ void __init ltq_soc_init(void) > } else if (of_machine_is_compatible("lantiq,ar9")) { > clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(), > ltq_ar9_fpi_hz(), CLOCK_250M); > - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); > - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); > + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); > + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); > clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1); > clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); > clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH); > @@ -562,8 +562,8 @@ void __init ltq_soc_init(void) > } else { > clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(), > ltq_danube_fpi_hz(), ltq_danube_pp32_hz()); > - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); > - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); > + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); > + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); > clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO); > clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU); > clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE); > diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig > index c1807d4a0079..968088ceaeb3 100644 > --- a/drivers/phy/Kconfig > +++ b/drivers/phy/Kconfig > @@ -52,6 +52,7 @@ source "drivers/phy/allwinner/Kconfig" > source "drivers/phy/amlogic/Kconfig" > source "drivers/phy/broadcom/Kconfig" > source "drivers/phy/hisilicon/Kconfig" > +source "drivers/phy/lantiq/Kconfig" > source "drivers/phy/marvell/Kconfig" > source "drivers/phy/motorola/Kconfig" > source "drivers/phy/qualcomm/Kconfig" > diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile > index f252201e0ec9..a8b9439a5d8e 100644 > --- a/drivers/phy/Makefile > +++ b/drivers/phy/Makefile > @@ -7,9 +7,9 @@ obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o > obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o > obj-$(CONFIG_PHY_XGENE) += phy-xgene.o > obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o > - > obj-$(CONFIG_ARCH_SUNXI) += allwinner/ > obj-$(CONFIG_ARCH_MESON) += amlogic/ > +obj-$(CONFIG_LANTIQ) += lantiq/ > obj-$(CONFIG_ARCH_RENESAS) += renesas/ > obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ > obj-$(CONFIG_ARCH_TEGRA) += tegra/ > diff --git a/drivers/phy/lantiq/Kconfig b/drivers/phy/lantiq/Kconfig > new file mode 100644 > index 000000000000..a2d5006b3dc7 > --- /dev/null > +++ b/drivers/phy/lantiq/Kconfig > @@ -0,0 +1,10 @@ > +# > +# Phy drivers for Lantiq / Intel platforms > +# > +config PHY_LANTIQ_RCU_USB2 > + tristate "Lantiq XWAY SoC RCU based USB PHY" > + depends on SOC_TYPE_XWAY depends on COMPILE_TEST.. > + depends on OF > + select GENERIC_PHY > + help > + Support for the USB PHY(s) on the Lantiq / Intel XWAY family SoCs. > diff --git a/drivers/phy/lantiq/Makefile b/drivers/phy/lantiq/Makefile > new file mode 100644 > index 000000000000..f73eb56a5416 > --- /dev/null > +++ b/drivers/phy/lantiq/Makefile > @@ -0,0 +1 @@ > +obj-$(CONFIG_PHY_LANTIQ_RCU_USB2) += phy-lantiq-rcu-usb2.o > diff --git a/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > new file mode 100644 > index 000000000000..8f5687737b50 > --- /dev/null > +++ b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c > @@ -0,0 +1,290 @@ > +/* > + * Lantiq XWAY SoC RCU module based USB 1.1/2.0 PHY driver > + * > + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com> > + * Copyright (C) 2017 Hauke Mehrtens <hauke@hauke-m.de> > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +#include <linux/clk.h> > +#include <linux/delay.h> > +#include <linux/mfd/syscon.h> > +#include <linux/module.h> > +#include <linux/of.h> > +#include <linux/of_address.h> > +#include <linux/of_device.h> > +#include <linux/phy/phy.h> > +#include <linux/platform_device.h> > +#include <linux/property.h> > +#include <linux/regmap.h> > +#include <linux/reset.h> > + > +/* Transmitter HS Pre-Emphasis Enable */ > +#define RCU_CFG1_TX_PEE BIT(0) > +/* Disconnect Threshold */ > +#define RCU_CFG1_DIS_THR_MASK 0x00038000 > +#define RCU_CFG1_DIS_THR_SHIFT 15 > + > +struct ltq_rcu_usb2_bits { > + u8 hostmode; > + u8 slave_endianness; > + u8 host_endianness; > + bool have_ana_cfg; > +}; > + > +struct ltq_rcu_usb2_priv { > + struct regmap *regmap; > + unsigned int phy_reg_offset; > + unsigned int ana_cfg1_reg_offset; > + const struct ltq_rcu_usb2_bits *reg_bits; > + struct device *dev; > + struct phy *phy; > + struct clk *ctrl_gate_clk; > + struct clk *phy_gate_clk; > + struct reset_control *ctrl_reset; > + struct reset_control *phy_reset; > +}; > + > +static const struct ltq_rcu_usb2_bits xway_rcu_usb2_reg_bits = { > + .hostmode = 11, > + .slave_endianness = 9, > + .host_endianness = 10, > + .have_ana_cfg = false, > +}; > + > +static const struct ltq_rcu_usb2_bits xrx100_rcu_usb2_reg_bits = { > + .hostmode = 11, > + .slave_endianness = 17, > + .host_endianness = 10, > + .have_ana_cfg = false, > +}; > + > +static const struct ltq_rcu_usb2_bits xrx200_rcu_usb2_reg_bits = { > + .hostmode = 11, > + .slave_endianness = 9, > + .host_endianness = 10, > + .have_ana_cfg = true, > +}; > + > +static const struct of_device_id ltq_rcu_usb2_phy_of_match[] = { > + { > + .compatible = "lantiq,ase-usb2-phy", > + .data = &xway_rcu_usb2_reg_bits, > + }, > + { > + .compatible = "lantiq,danube-usb2-phy", > + .data = &xway_rcu_usb2_reg_bits, > + }, > + { > + .compatible = "lantiq,xrx100-usb2-phy", > + .data = &xrx100_rcu_usb2_reg_bits, > + }, > + { > + .compatible = "lantiq,xrx200-usb2-phy", > + .data = &xrx200_rcu_usb2_reg_bits, > + }, > + { > + .compatible = "lantiq,xrx300-usb2-phy", > + .data = &xrx200_rcu_usb2_reg_bits, > + }, > + { }, > +}; > +MODULE_DEVICE_TABLE(of, ltq_rcu_usb2_phy_of_match); > + > + spurious blank line.. > +static int ltq_rcu_usb2_phy_power_on(struct phy *phy) > +{ > + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); > + > + reset_control_deassert(priv->phy_reset); > + > + return 0; > +} > + > +static int ltq_rcu_usb2_phy_power_off(struct phy *phy) > +{ > + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); > + > + reset_control_assert(priv->phy_reset); > + > + return 0; > +} > + > +static struct phy_ops ltq_rcu_usb2_phy_ops = { > + .power_on = ltq_rcu_usb2_phy_power_on, > + .power_off = ltq_rcu_usb2_phy_power_off, > + .owner = THIS_MODULE, > +}; > + > +static int ltq_rcu_usb2_start_cores(struct ltq_rcu_usb2_priv *priv) > +{ > + struct device *dev = priv->dev; > + int ret; > + > + /* Power on the USB core. */ > + ret = clk_prepare_enable(priv->ctrl_gate_clk); > + if (ret) { > + dev_err(dev, "failed to enable CTRL gate\n"); > + return ret; > + } > + > + /* > + * Power on the USB PHY. We have to do it early because > + * otherwise the second core won't turn on properly. > + */ > + ret = clk_prepare_enable(priv->phy_gate_clk); > + if (ret) { > + clk_disable_unprepare(priv->ctrl_gate_clk); > + dev_err(dev, "failed to enable PHY gate\n"); > + return ret; > + } why are these not part of power_on callback? > + > + if (priv->reg_bits->have_ana_cfg) { > + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, > + RCU_CFG1_TX_PEE, RCU_CFG1_TX_PEE); > + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, > + RCU_CFG1_DIS_THR_MASK, 7 << RCU_CFG1_DIS_THR_SHIFT); > + } > + > + /* Configure core to host mode */ > + regmap_update_bits(priv->regmap, priv->phy_reg_offset, > + BIT(priv->reg_bits->hostmode), 0); > + > + /* Select DMA endianness (Host-endian: big-endian) */ > + regmap_update_bits(priv->regmap, priv->phy_reg_offset, > + BIT(priv->reg_bits->slave_endianness), 0); > + regmap_update_bits(priv->regmap, priv->phy_reg_offset, > + BIT(priv->reg_bits->host_endianness), > + BIT(priv->reg_bits->host_endianness)); All this can be phy_init? > + > + /* Reset USB core throgh reset controller */ > + reset_control_deassert(priv->ctrl_reset); > + > + reset_control_assert(priv->phy_reset); > + > + return 0; > +} > + > +static int ltq_rcu_usb2_of_probe(struct ltq_rcu_usb2_priv *priv, > + struct platform_device *pdev) %s/ltq_rcu_usb2_of_probe/ltq_rcu_usb2_of_parse > +{ > + struct device *dev = priv->dev; > + struct resource *res; > + struct resource res_parent; > + int ret; > + > + priv->reg_bits = of_device_get_match_data(dev); > + > + priv->regmap = syscon_node_to_regmap(dev->of_node->parent); > + if (IS_ERR(priv->regmap)) { > + dev_err(dev, "Failed to lookup RCU regmap\n"); > + return PTR_ERR(priv->regmap); > + } > + > + ret = of_address_to_resource(dev->of_node->parent, 0, &res_parent); > + if (ret) > + return ret; > + > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!res) { > + dev_err(dev, "Failed to get RCU PHY reg offset\n"); > + return ret; > + } > + > + if (res->start < res_parent.start) > + return -ENOENT; > + priv->phy_reg_offset = res->start - res_parent.start; I think you can simple use of_get_address() to get the offset. Thanks Kishon -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On 08/08/2017 01:58 PM, Kishon Vijay Abraham I wrote: > Hi, > > On Thursday 03 August 2017 04:27 AM, Hauke Mehrtens wrote: >> This driver starts the DWC2 core(s) built into the XWAY SoCs and provides >> the PHY interfaces for each core. The phy instances can be passed to the >> dwc2 driver, which already supports the generic phy interface. >> >> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> >> Cc: Kishon Vijay Abraham I <kishon@ti.com> >> --- >> .../bindings/phy/phy-lantiq-rcu-usb2.txt | 43 +++ >> arch/mips/lantiq/xway/sysctrl.c | 24 +- >> drivers/phy/Kconfig | 1 + >> drivers/phy/Makefile | 2 +- >> drivers/phy/lantiq/Kconfig | 10 + >> drivers/phy/lantiq/Makefile | 1 + >> drivers/phy/lantiq/phy-lantiq-rcu-usb2.c | 290 +++++++++++++++++++++ >> 7 files changed, 358 insertions(+), 13 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt >> create mode 100644 drivers/phy/lantiq/Kconfig >> create mode 100644 drivers/phy/lantiq/Makefile >> create mode 100644 drivers/phy/lantiq/phy-lantiq-rcu-usb2.c >> >> diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt >> new file mode 100644 >> index 000000000000..76036c5c5d11 >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt >> @@ -0,0 +1,43 @@ >> +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding >> +=========================================== >> + >> +This binding describes the USB PHY hardware provided by the RCU module on the >> +Lantiq XWAY SoCs. >> + >> +This driver has to be a sub node of the Lantiq RCU block. >> + >> +------------------------------------------------------------------------------- >> +Required properties (controller (parent) node): >> +- compatible : Should be one of >> + "lantiq,ase-usb2-phy" >> + "lantiq,danube-usb2-phy" >> + "lantiq,xrx100-usb2-phy" >> + "lantiq,xrx200-usb2-phy" >> + "lantiq,xrx300-usb2-phy" >> +- reg : Defines the following sets of registers in the parent >> + syscon device >> + - Offset of the USB PHY configuration register >> + - Offset of the USB Analog configuration >> + register (only for xrx200 and xrx200) >> +- clocks : References to the (PMU) "ctrl" and "phy" clk gates. >> +- clock-names : Must be one of the following: >> + "ctrl" >> + "phy" >> +- resets : References to the RCU USB configuration reset bits. >> +- reset-names : Must be one of the following: >> + "phy" (optional) >> + "ctrl" (shared) >> + >> +------------------------------------------------------------------------------- >> +Example for the USB PHYs on an xRX200 SoC: >> + usb_phy0: usb2-phy@18 { >> + compatible = "lantiq,xrx200-usb2-phy"; >> + reg = <0x18 4>, <0x38 4>; >> + >> + clocks = <&pmu PMU_GATE_USB0_CTRL>, >> + <&pmu PMU_GATE_USB0_PHY>; >> + clock-names = "ctrl", "phy"; >> + resets = <&reset1 4 4>, <&reset0 4 4>; >> + reset-names = "phy", "ctrl"; >> + #phy-cells = <0>; >> + }; > > Please CC device tree list and get Ack from devicetree maintainers for this > binding. Preferable send this as a separate patch. The device tree mailing list is already on CC >> diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c >> index 87eab4d288e5..f76978e4da32 100644 >> --- a/arch/mips/lantiq/xway/sysctrl.c >> +++ b/arch/mips/lantiq/xway/sysctrl.c >> @@ -469,8 +469,8 @@ void __init ltq_soc_init(void) >> >> if (of_machine_is_compatible("lantiq,grx390") || >> of_machine_is_compatible("lantiq,ar10")) { >> - clkdev_add_pmu("1e101000.usb", "phy", 1, 2, PMU_ANALOG_USB0_P); >> - clkdev_add_pmu("1e106000.usb", "phy", 1, 2, PMU_ANALOG_USB1_P); >> + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB0_P); >> + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB1_P); >> /* rc 0 */ >> clkdev_add_pmu("1d900000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE0_P); >> clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); >> @@ -490,8 +490,8 @@ void __init ltq_soc_init(void) >> else >> clkdev_add_static(CLOCK_133M, CLOCK_133M, >> CLOCK_133M, CLOCK_133M); >> - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); >> - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); >> + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); >> + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); >> clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE); >> clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY); >> clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY); >> @@ -526,10 +526,10 @@ void __init ltq_soc_init(void) >> } else if (of_machine_is_compatible("lantiq,vr9")) { >> clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(), >> ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz()); >> - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); >> - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0 | PMU_AHBM); >> - clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); >> - clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1 | PMU_AHBM); >> + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); >> + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0 | PMU_AHBM); >> + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 0, PMU_USB1_P); >> + clkdev_add_pmu("1f203034.usb2-phy", "ctrl", 1, 0, PMU_USB1 | PMU_AHBM); >> clkdev_add_pmu("1d900000.pcie", "phy", 1, 1, PMU1_PCIE_PHY); >> clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK); >> clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); >> @@ -550,8 +550,8 @@ void __init ltq_soc_init(void) >> } else if (of_machine_is_compatible("lantiq,ar9")) { >> clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(), >> ltq_ar9_fpi_hz(), CLOCK_250M); >> - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); >> - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); >> + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); >> + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); >> clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1); >> clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); >> clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH); >> @@ -562,8 +562,8 @@ void __init ltq_soc_init(void) >> } else { >> clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(), >> ltq_danube_fpi_hz(), ltq_danube_pp32_hz()); >> - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); >> - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); >> + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); >> + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); >> clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO); >> clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU); >> clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE); >> diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig >> index c1807d4a0079..968088ceaeb3 100644 >> --- a/drivers/phy/Kconfig >> +++ b/drivers/phy/Kconfig >> @@ -52,6 +52,7 @@ source "drivers/phy/allwinner/Kconfig" >> source "drivers/phy/amlogic/Kconfig" >> source "drivers/phy/broadcom/Kconfig" >> source "drivers/phy/hisilicon/Kconfig" >> +source "drivers/phy/lantiq/Kconfig" >> source "drivers/phy/marvell/Kconfig" >> source "drivers/phy/motorola/Kconfig" >> source "drivers/phy/qualcomm/Kconfig" >> diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile >> index f252201e0ec9..a8b9439a5d8e 100644 >> --- a/drivers/phy/Makefile >> +++ b/drivers/phy/Makefile >> @@ -7,9 +7,9 @@ obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o >> obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o >> obj-$(CONFIG_PHY_XGENE) += phy-xgene.o >> obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o >> - >> obj-$(CONFIG_ARCH_SUNXI) += allwinner/ >> obj-$(CONFIG_ARCH_MESON) += amlogic/ >> +obj-$(CONFIG_LANTIQ) += lantiq/ >> obj-$(CONFIG_ARCH_RENESAS) += renesas/ >> obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ >> obj-$(CONFIG_ARCH_TEGRA) += tegra/ >> diff --git a/drivers/phy/lantiq/Kconfig b/drivers/phy/lantiq/Kconfig >> new file mode 100644 >> index 000000000000..a2d5006b3dc7 >> --- /dev/null >> +++ b/drivers/phy/lantiq/Kconfig >> @@ -0,0 +1,10 @@ >> +# >> +# Phy drivers for Lantiq / Intel platforms >> +# >> +config PHY_LANTIQ_RCU_USB2 >> + tristate "Lantiq XWAY SoC RCU based USB PHY" >> + depends on SOC_TYPE_XWAY > > depends on COMPILE_TEST.. done >> + depends on OF >> + select GENERIC_PHY >> + help >> + Support for the USB PHY(s) on the Lantiq / Intel XWAY family SoCs. >> diff --git a/drivers/phy/lantiq/Makefile b/drivers/phy/lantiq/Makefile >> new file mode 100644 >> index 000000000000..f73eb56a5416 >> --- /dev/null >> +++ b/drivers/phy/lantiq/Makefile >> @@ -0,0 +1 @@ >> +obj-$(CONFIG_PHY_LANTIQ_RCU_USB2) += phy-lantiq-rcu-usb2.o >> diff --git a/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c >> new file mode 100644 >> index 000000000000..8f5687737b50 >> --- /dev/null >> +++ b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c >> @@ -0,0 +1,290 @@ >> +/* >> + * Lantiq XWAY SoC RCU module based USB 1.1/2.0 PHY driver >> + * >> + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com> >> + * Copyright (C) 2017 Hauke Mehrtens <hauke@hauke-m.de> >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License version 2 as >> + * published by the Free Software Foundation. >> + */ >> + >> +#include <linux/clk.h> >> +#include <linux/delay.h> >> +#include <linux/mfd/syscon.h> >> +#include <linux/module.h> >> +#include <linux/of.h> >> +#include <linux/of_address.h> >> +#include <linux/of_device.h> >> +#include <linux/phy/phy.h> >> +#include <linux/platform_device.h> >> +#include <linux/property.h> >> +#include <linux/regmap.h> >> +#include <linux/reset.h> >> + >> +/* Transmitter HS Pre-Emphasis Enable */ >> +#define RCU_CFG1_TX_PEE BIT(0) >> +/* Disconnect Threshold */ >> +#define RCU_CFG1_DIS_THR_MASK 0x00038000 >> +#define RCU_CFG1_DIS_THR_SHIFT 15 >> + >> +struct ltq_rcu_usb2_bits { >> + u8 hostmode; >> + u8 slave_endianness; >> + u8 host_endianness; >> + bool have_ana_cfg; >> +}; >> + >> +struct ltq_rcu_usb2_priv { >> + struct regmap *regmap; >> + unsigned int phy_reg_offset; >> + unsigned int ana_cfg1_reg_offset; >> + const struct ltq_rcu_usb2_bits *reg_bits; >> + struct device *dev; >> + struct phy *phy; >> + struct clk *ctrl_gate_clk; >> + struct clk *phy_gate_clk; >> + struct reset_control *ctrl_reset; >> + struct reset_control *phy_reset; >> +}; >> + >> +static const struct ltq_rcu_usb2_bits xway_rcu_usb2_reg_bits = { >> + .hostmode = 11, >> + .slave_endianness = 9, >> + .host_endianness = 10, >> + .have_ana_cfg = false, >> +}; >> + >> +static const struct ltq_rcu_usb2_bits xrx100_rcu_usb2_reg_bits = { >> + .hostmode = 11, >> + .slave_endianness = 17, >> + .host_endianness = 10, >> + .have_ana_cfg = false, >> +}; >> + >> +static const struct ltq_rcu_usb2_bits xrx200_rcu_usb2_reg_bits = { >> + .hostmode = 11, >> + .slave_endianness = 9, >> + .host_endianness = 10, >> + .have_ana_cfg = true, >> +}; >> + >> +static const struct of_device_id ltq_rcu_usb2_phy_of_match[] = { >> + { >> + .compatible = "lantiq,ase-usb2-phy", >> + .data = &xway_rcu_usb2_reg_bits, >> + }, >> + { >> + .compatible = "lantiq,danube-usb2-phy", >> + .data = &xway_rcu_usb2_reg_bits, >> + }, >> + { >> + .compatible = "lantiq,xrx100-usb2-phy", >> + .data = &xrx100_rcu_usb2_reg_bits, >> + }, >> + { >> + .compatible = "lantiq,xrx200-usb2-phy", >> + .data = &xrx200_rcu_usb2_reg_bits, >> + }, >> + { >> + .compatible = "lantiq,xrx300-usb2-phy", >> + .data = &xrx200_rcu_usb2_reg_bits, >> + }, >> + { }, >> +}; >> +MODULE_DEVICE_TABLE(of, ltq_rcu_usb2_phy_of_match); >> + >> + > spurious blank line.. done >> +static int ltq_rcu_usb2_phy_power_on(struct phy *phy) >> +{ >> + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); >> + >> + reset_control_deassert(priv->phy_reset); >> + >> + return 0; >> +} >> + >> +static int ltq_rcu_usb2_phy_power_off(struct phy *phy) >> +{ >> + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); >> + >> + reset_control_assert(priv->phy_reset); >> + >> + return 0; >> +} >> + >> +static struct phy_ops ltq_rcu_usb2_phy_ops = { >> + .power_on = ltq_rcu_usb2_phy_power_on, >> + .power_off = ltq_rcu_usb2_phy_power_off, >> + .owner = THIS_MODULE, >> +}; >> + >> +static int ltq_rcu_usb2_start_cores(struct ltq_rcu_usb2_priv *priv) >> +{ >> + struct device *dev = priv->dev; >> + int ret; >> + >> + /* Power on the USB core. */ >> + ret = clk_prepare_enable(priv->ctrl_gate_clk); >> + if (ret) { >> + dev_err(dev, "failed to enable CTRL gate\n"); >> + return ret; >> + } >> + >> + /* >> + * Power on the USB PHY. We have to do it early because >> + * otherwise the second core won't turn on properly. >> + */ >> + ret = clk_prepare_enable(priv->phy_gate_clk); >> + if (ret) { >> + clk_disable_unprepare(priv->ctrl_gate_clk); >> + dev_err(dev, "failed to enable PHY gate\n"); >> + return ret; >> + } > > why are these not part of power_on callback? I moved them now to power_on() >> + >> + if (priv->reg_bits->have_ana_cfg) { >> + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, >> + RCU_CFG1_TX_PEE, RCU_CFG1_TX_PEE); >> + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, >> + RCU_CFG1_DIS_THR_MASK, 7 << RCU_CFG1_DIS_THR_SHIFT); >> + } >> + >> + /* Configure core to host mode */ >> + regmap_update_bits(priv->regmap, priv->phy_reg_offset, >> + BIT(priv->reg_bits->hostmode), 0); >> + >> + /* Select DMA endianness (Host-endian: big-endian) */ >> + regmap_update_bits(priv->regmap, priv->phy_reg_offset, >> + BIT(priv->reg_bits->slave_endianness), 0); >> + regmap_update_bits(priv->regmap, priv->phy_reg_offset, >> + BIT(priv->reg_bits->host_endianness), >> + BIT(priv->reg_bits->host_endianness)); > > All this can be phy_init? I moved them to init() >> + >> + /* Reset USB core throgh reset controller */ >> + reset_control_deassert(priv->ctrl_reset); >> + >> + reset_control_assert(priv->phy_reset); >> + >> + return 0; >> +} >> + >> +static int ltq_rcu_usb2_of_probe(struct ltq_rcu_usb2_priv *priv, >> + struct platform_device *pdev) > > %s/ltq_rcu_usb2_of_probe/ltq_rcu_usb2_of_parse done >> +{ >> + struct device *dev = priv->dev; >> + struct resource *res; >> + struct resource res_parent; >> + int ret; >> + >> + priv->reg_bits = of_device_get_match_data(dev); >> + >> + priv->regmap = syscon_node_to_regmap(dev->of_node->parent); >> + if (IS_ERR(priv->regmap)) { >> + dev_err(dev, "Failed to lookup RCU regmap\n"); >> + return PTR_ERR(priv->regmap); >> + } >> + >> + ret = of_address_to_resource(dev->of_node->parent, 0, &res_parent); >> + if (ret) >> + return ret; >> + >> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); >> + if (!res) { >> + dev_err(dev, "Failed to get RCU PHY reg offset\n"); >> + return ret; >> + } >> + >> + if (res->start < res_parent.start) >> + return -ENOENT; >> + priv->phy_reg_offset = res->start - res_parent.start; > > I think you can simple use of_get_address() to get the offset. Yes that works, thanks for the hint. Hauke -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt new file mode 100644 index 000000000000..76036c5c5d11 --- /dev/null +++ b/Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt @@ -0,0 +1,43 @@ +Lantiq XWAY SoC RCU USB 1.1/2.0 PHY binding +=========================================== + +This binding describes the USB PHY hardware provided by the RCU module on the +Lantiq XWAY SoCs. + +This driver has to be a sub node of the Lantiq RCU block. + +------------------------------------------------------------------------------- +Required properties (controller (parent) node): +- compatible : Should be one of + "lantiq,ase-usb2-phy" + "lantiq,danube-usb2-phy" + "lantiq,xrx100-usb2-phy" + "lantiq,xrx200-usb2-phy" + "lantiq,xrx300-usb2-phy" +- reg : Defines the following sets of registers in the parent + syscon device + - Offset of the USB PHY configuration register + - Offset of the USB Analog configuration + register (only for xrx200 and xrx200) +- clocks : References to the (PMU) "ctrl" and "phy" clk gates. +- clock-names : Must be one of the following: + "ctrl" + "phy" +- resets : References to the RCU USB configuration reset bits. +- reset-names : Must be one of the following: + "phy" (optional) + "ctrl" (shared) + +------------------------------------------------------------------------------- +Example for the USB PHYs on an xRX200 SoC: + usb_phy0: usb2-phy@18 { + compatible = "lantiq,xrx200-usb2-phy"; + reg = <0x18 4>, <0x38 4>; + + clocks = <&pmu PMU_GATE_USB0_CTRL>, + <&pmu PMU_GATE_USB0_PHY>; + clock-names = "ctrl", "phy"; + resets = <&reset1 4 4>, <&reset0 4 4>; + reset-names = "phy", "ctrl"; + #phy-cells = <0>; + }; diff --git a/arch/mips/lantiq/xway/sysctrl.c b/arch/mips/lantiq/xway/sysctrl.c index 87eab4d288e5..f76978e4da32 100644 --- a/arch/mips/lantiq/xway/sysctrl.c +++ b/arch/mips/lantiq/xway/sysctrl.c @@ -469,8 +469,8 @@ void __init ltq_soc_init(void) if (of_machine_is_compatible("lantiq,grx390") || of_machine_is_compatible("lantiq,ar10")) { - clkdev_add_pmu("1e101000.usb", "phy", 1, 2, PMU_ANALOG_USB0_P); - clkdev_add_pmu("1e106000.usb", "phy", 1, 2, PMU_ANALOG_USB1_P); + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB0_P); + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 2, PMU_ANALOG_USB1_P); /* rc 0 */ clkdev_add_pmu("1d900000.pcie", "phy", 1, 2, PMU_ANALOG_PCIE0_P); clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); @@ -490,8 +490,8 @@ void __init ltq_soc_init(void) else clkdev_add_static(CLOCK_133M, CLOCK_133M, CLOCK_133M, CLOCK_133M); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e180000.etop", "ppe", 1, 0, PMU_PPE); clkdev_add_cgu("1e180000.etop", "ephycgu", CGU_EPHY); clkdev_add_pmu("1e180000.etop", "ephy", 1, 0, PMU_EPHY); @@ -526,10 +526,10 @@ void __init ltq_soc_init(void) } else if (of_machine_is_compatible("lantiq,vr9")) { clkdev_add_static(ltq_vr9_cpu_hz(), ltq_vr9_fpi_hz(), ltq_vr9_fpi_hz(), ltq_vr9_pp32_hz()); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0 | PMU_AHBM); - clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); - clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1 | PMU_AHBM); + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0 | PMU_AHBM); + clkdev_add_pmu("1f203034.usb2-phy", "phy", 1, 0, PMU_USB1_P); + clkdev_add_pmu("1f203034.usb2-phy", "ctrl", 1, 0, PMU_USB1 | PMU_AHBM); clkdev_add_pmu("1d900000.pcie", "phy", 1, 1, PMU1_PCIE_PHY); clkdev_add_pmu("1d900000.pcie", "bus", 1, 0, PMU_PCIE_CLK); clkdev_add_pmu("1d900000.pcie", "msi", 1, 1, PMU1_PCIE_MSI); @@ -550,8 +550,8 @@ void __init ltq_soc_init(void) } else if (of_machine_is_compatible("lantiq,ar9")) { clkdev_add_static(ltq_ar9_cpu_hz(), ltq_ar9_fpi_hz(), ltq_ar9_fpi_hz(), CLOCK_250M); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e106000.usb", "ctl", 1, 0, PMU_USB1); clkdev_add_pmu("1e106000.usb", "phy", 1, 0, PMU_USB1_P); clkdev_add_pmu("1e180000.etop", "switch", 1, 0, PMU_SWITCH); @@ -562,8 +562,8 @@ void __init ltq_soc_init(void) } else { clkdev_add_static(ltq_danube_cpu_hz(), ltq_danube_fpi_hz(), ltq_danube_fpi_hz(), ltq_danube_pp32_hz()); - clkdev_add_pmu("1e101000.usb", "ctl", 1, 0, PMU_USB0); - clkdev_add_pmu("1e101000.usb", "phy", 1, 0, PMU_USB0_P); + clkdev_add_pmu("1f203018.usb2-phy", "ctrl", 1, 0, PMU_USB0); + clkdev_add_pmu("1f203018.usb2-phy", "phy", 1, 0, PMU_USB0_P); clkdev_add_pmu("1e103000.sdio", NULL, 1, 0, PMU_SDIO); clkdev_add_pmu("1e103100.deu", NULL, 1, 0, PMU_DEU); clkdev_add_pmu("1e116000.mei", "dfe", 1, 0, PMU_DFE); diff --git a/drivers/phy/Kconfig b/drivers/phy/Kconfig index c1807d4a0079..968088ceaeb3 100644 --- a/drivers/phy/Kconfig +++ b/drivers/phy/Kconfig @@ -52,6 +52,7 @@ source "drivers/phy/allwinner/Kconfig" source "drivers/phy/amlogic/Kconfig" source "drivers/phy/broadcom/Kconfig" source "drivers/phy/hisilicon/Kconfig" +source "drivers/phy/lantiq/Kconfig" source "drivers/phy/marvell/Kconfig" source "drivers/phy/motorola/Kconfig" source "drivers/phy/qualcomm/Kconfig" diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile index f252201e0ec9..a8b9439a5d8e 100644 --- a/drivers/phy/Makefile +++ b/drivers/phy/Makefile @@ -7,9 +7,9 @@ obj-$(CONFIG_PHY_LPC18XX_USB_OTG) += phy-lpc18xx-usb-otg.o obj-$(CONFIG_PHY_MT65XX_USB3) += phy-mt65xx-usb3.o obj-$(CONFIG_PHY_XGENE) += phy-xgene.o obj-$(CONFIG_PHY_PISTACHIO_USB) += phy-pistachio-usb.o - obj-$(CONFIG_ARCH_SUNXI) += allwinner/ obj-$(CONFIG_ARCH_MESON) += amlogic/ +obj-$(CONFIG_LANTIQ) += lantiq/ obj-$(CONFIG_ARCH_RENESAS) += renesas/ obj-$(CONFIG_ARCH_ROCKCHIP) += rockchip/ obj-$(CONFIG_ARCH_TEGRA) += tegra/ diff --git a/drivers/phy/lantiq/Kconfig b/drivers/phy/lantiq/Kconfig new file mode 100644 index 000000000000..a2d5006b3dc7 --- /dev/null +++ b/drivers/phy/lantiq/Kconfig @@ -0,0 +1,10 @@ +# +# Phy drivers for Lantiq / Intel platforms +# +config PHY_LANTIQ_RCU_USB2 + tristate "Lantiq XWAY SoC RCU based USB PHY" + depends on SOC_TYPE_XWAY + depends on OF + select GENERIC_PHY + help + Support for the USB PHY(s) on the Lantiq / Intel XWAY family SoCs. diff --git a/drivers/phy/lantiq/Makefile b/drivers/phy/lantiq/Makefile new file mode 100644 index 000000000000..f73eb56a5416 --- /dev/null +++ b/drivers/phy/lantiq/Makefile @@ -0,0 +1 @@ +obj-$(CONFIG_PHY_LANTIQ_RCU_USB2) += phy-lantiq-rcu-usb2.o diff --git a/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c new file mode 100644 index 000000000000..8f5687737b50 --- /dev/null +++ b/drivers/phy/lantiq/phy-lantiq-rcu-usb2.c @@ -0,0 +1,290 @@ +/* + * Lantiq XWAY SoC RCU module based USB 1.1/2.0 PHY driver + * + * Copyright (C) 2016 Martin Blumenstingl <martin.blumenstingl@googlemail.com> + * Copyright (C) 2017 Hauke Mehrtens <hauke@hauke-m.de> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/clk.h> +#include <linux/delay.h> +#include <linux/mfd/syscon.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/phy/phy.h> +#include <linux/platform_device.h> +#include <linux/property.h> +#include <linux/regmap.h> +#include <linux/reset.h> + +/* Transmitter HS Pre-Emphasis Enable */ +#define RCU_CFG1_TX_PEE BIT(0) +/* Disconnect Threshold */ +#define RCU_CFG1_DIS_THR_MASK 0x00038000 +#define RCU_CFG1_DIS_THR_SHIFT 15 + +struct ltq_rcu_usb2_bits { + u8 hostmode; + u8 slave_endianness; + u8 host_endianness; + bool have_ana_cfg; +}; + +struct ltq_rcu_usb2_priv { + struct regmap *regmap; + unsigned int phy_reg_offset; + unsigned int ana_cfg1_reg_offset; + const struct ltq_rcu_usb2_bits *reg_bits; + struct device *dev; + struct phy *phy; + struct clk *ctrl_gate_clk; + struct clk *phy_gate_clk; + struct reset_control *ctrl_reset; + struct reset_control *phy_reset; +}; + +static const struct ltq_rcu_usb2_bits xway_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 9, + .host_endianness = 10, + .have_ana_cfg = false, +}; + +static const struct ltq_rcu_usb2_bits xrx100_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 17, + .host_endianness = 10, + .have_ana_cfg = false, +}; + +static const struct ltq_rcu_usb2_bits xrx200_rcu_usb2_reg_bits = { + .hostmode = 11, + .slave_endianness = 9, + .host_endianness = 10, + .have_ana_cfg = true, +}; + +static const struct of_device_id ltq_rcu_usb2_phy_of_match[] = { + { + .compatible = "lantiq,ase-usb2-phy", + .data = &xway_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,danube-usb2-phy", + .data = &xway_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx100-usb2-phy", + .data = &xrx100_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx200-usb2-phy", + .data = &xrx200_rcu_usb2_reg_bits, + }, + { + .compatible = "lantiq,xrx300-usb2-phy", + .data = &xrx200_rcu_usb2_reg_bits, + }, + { }, +}; +MODULE_DEVICE_TABLE(of, ltq_rcu_usb2_phy_of_match); + + +static int ltq_rcu_usb2_phy_power_on(struct phy *phy) +{ + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); + + reset_control_deassert(priv->phy_reset); + + return 0; +} + +static int ltq_rcu_usb2_phy_power_off(struct phy *phy) +{ + struct ltq_rcu_usb2_priv *priv = phy_get_drvdata(phy); + + reset_control_assert(priv->phy_reset); + + return 0; +} + +static struct phy_ops ltq_rcu_usb2_phy_ops = { + .power_on = ltq_rcu_usb2_phy_power_on, + .power_off = ltq_rcu_usb2_phy_power_off, + .owner = THIS_MODULE, +}; + +static int ltq_rcu_usb2_start_cores(struct ltq_rcu_usb2_priv *priv) +{ + struct device *dev = priv->dev; + int ret; + + /* Power on the USB core. */ + ret = clk_prepare_enable(priv->ctrl_gate_clk); + if (ret) { + dev_err(dev, "failed to enable CTRL gate\n"); + return ret; + } + + /* + * Power on the USB PHY. We have to do it early because + * otherwise the second core won't turn on properly. + */ + ret = clk_prepare_enable(priv->phy_gate_clk); + if (ret) { + clk_disable_unprepare(priv->ctrl_gate_clk); + dev_err(dev, "failed to enable PHY gate\n"); + return ret; + } + + if (priv->reg_bits->have_ana_cfg) { + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, + RCU_CFG1_TX_PEE, RCU_CFG1_TX_PEE); + regmap_update_bits(priv->regmap, priv->ana_cfg1_reg_offset, + RCU_CFG1_DIS_THR_MASK, 7 << RCU_CFG1_DIS_THR_SHIFT); + } + + /* Configure core to host mode */ + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->hostmode), 0); + + /* Select DMA endianness (Host-endian: big-endian) */ + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->slave_endianness), 0); + regmap_update_bits(priv->regmap, priv->phy_reg_offset, + BIT(priv->reg_bits->host_endianness), + BIT(priv->reg_bits->host_endianness)); + + /* Reset USB core throgh reset controller */ + reset_control_deassert(priv->ctrl_reset); + + reset_control_assert(priv->phy_reset); + + return 0; +} + +static int ltq_rcu_usb2_of_probe(struct ltq_rcu_usb2_priv *priv, + struct platform_device *pdev) +{ + struct device *dev = priv->dev; + struct resource *res; + struct resource res_parent; + int ret; + + priv->reg_bits = of_device_get_match_data(dev); + + priv->regmap = syscon_node_to_regmap(dev->of_node->parent); + if (IS_ERR(priv->regmap)) { + dev_err(dev, "Failed to lookup RCU regmap\n"); + return PTR_ERR(priv->regmap); + } + + ret = of_address_to_resource(dev->of_node->parent, 0, &res_parent); + if (ret) + return ret; + + res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res) { + dev_err(dev, "Failed to get RCU PHY reg offset\n"); + return ret; + } + + if (res->start < res_parent.start) + return -ENOENT; + priv->phy_reg_offset = res->start - res_parent.start; + + if (priv->reg_bits->have_ana_cfg) { + res = platform_get_resource(pdev, IORESOURCE_MEM, 1); + if (!res) { + dev_err(dev, "Failed to get RCU ANA CFG1 reg offset\n"); + return ret; + } + + if (res->start < res_parent.start) + return -ENOENT; + priv->ana_cfg1_reg_offset = res->start - res_parent.start; + } + + priv->ctrl_gate_clk = devm_clk_get(dev, "ctrl"); + if (IS_ERR(priv->ctrl_gate_clk)) { + dev_err(dev, "Unable to get USB ctrl gate clk\n"); + return PTR_ERR(priv->ctrl_gate_clk); + } + + priv->phy_gate_clk = devm_clk_get(dev, "phy"); + if (IS_ERR(priv->phy_gate_clk)) { + dev_err(dev, "Unable to get USB phy gate clk\n"); + return PTR_ERR(priv->phy_gate_clk); + } + + priv->ctrl_reset = devm_reset_control_get_shared(dev, "ctrl"); + if (IS_ERR(priv->ctrl_reset)) { + if (PTR_ERR(priv->ctrl_reset) != -EPROBE_DEFER) + dev_err(dev, "failed to get 'ctrl' reset\n"); + return PTR_ERR(priv->ctrl_reset); + } + + priv->phy_reset = devm_reset_control_get_optional(dev, "phy"); + if (IS_ERR(priv->phy_reset)) + return PTR_ERR(priv->phy_reset); + + return 0; +} + +static int ltq_rcu_usb2_phy_probe(struct platform_device *pdev) +{ + struct device *dev = &pdev->dev; + struct ltq_rcu_usb2_priv *priv; + struct phy_provider *provider; + int ret; + + priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL); + if (!priv) + return -ENOMEM; + + priv->dev = dev; + + ret = ltq_rcu_usb2_of_probe(priv, pdev); + if (ret) + return ret; + + priv->phy = devm_phy_create(dev, dev->of_node, <q_rcu_usb2_phy_ops); + if (IS_ERR(priv->phy)) { + dev_err(dev, "failed to create PHY\n"); + return PTR_ERR(priv->phy); + } + + phy_set_drvdata(priv->phy, priv); + + ret = ltq_rcu_usb2_start_cores(priv); + if (ret) + return ret; + + provider = devm_of_phy_provider_register(dev, of_phy_simple_xlate); + if (IS_ERR(provider)) { + clk_disable_unprepare(priv->phy_gate_clk); + clk_disable_unprepare(priv->ctrl_gate_clk); + return PTR_ERR(provider); + } + + dev_set_drvdata(priv->dev, priv); + return 0; +} + +static struct platform_driver ltq_rcu_usb2_phy_driver = { + .probe = ltq_rcu_usb2_phy_probe, + .driver = { + .name = "lantiq-rcu-usb2-phy", + .of_match_table = ltq_rcu_usb2_phy_of_match, + } +}; +module_platform_driver(ltq_rcu_usb2_phy_driver); + +MODULE_AUTHOR("Martin Blumenstingl <martin.blumenstingl@googlemail.com>"); +MODULE_DESCRIPTION("Lantiq XWAY USB2 PHY driver"); +MODULE_LICENSE("GPL v2");
This driver starts the DWC2 core(s) built into the XWAY SoCs and provides the PHY interfaces for each core. The phy instances can be passed to the dwc2 driver, which already supports the generic phy interface. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Cc: Kishon Vijay Abraham I <kishon@ti.com> --- .../bindings/phy/phy-lantiq-rcu-usb2.txt | 43 +++ arch/mips/lantiq/xway/sysctrl.c | 24 +- drivers/phy/Kconfig | 1 + drivers/phy/Makefile | 2 +- drivers/phy/lantiq/Kconfig | 10 + drivers/phy/lantiq/Makefile | 1 + drivers/phy/lantiq/phy-lantiq-rcu-usb2.c | 290 +++++++++++++++++++++ 7 files changed, 358 insertions(+), 13 deletions(-) create mode 100644 Documentation/devicetree/bindings/phy/phy-lantiq-rcu-usb2.txt create mode 100644 drivers/phy/lantiq/Kconfig create mode 100644 drivers/phy/lantiq/Makefile create mode 100644 drivers/phy/lantiq/phy-lantiq-rcu-usb2.c