deleted file mode 100644
@@ -1,1224 +0,0 @@
-/*
- * Freescale QuadSPI driver.
- *
- * Copyright (C) 2013 Freescale Semiconductor, Inc.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- */
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/interrupt.h>
-#include <linux/errno.h>
-#include <linux/platform_device.h>
-#include <linux/sched.h>
-#include <linux/delay.h>
-#include <linux/io.h>
-#include <linux/clk.h>
-#include <linux/err.h>
-#include <linux/of.h>
-#include <linux/of_device.h>
-#include <linux/timer.h>
-#include <linux/jiffies.h>
-#include <linux/completion.h>
-#include <linux/mtd/mtd.h>
-#include <linux/mtd/partitions.h>
-#include <linux/mtd/spi-nor.h>
-#include <linux/mutex.h>
-#include <linux/pm_qos.h>
-#include <linux/sizes.h>
-
-/* Controller needs driver to swap endian */
-#define QUADSPI_QUIRK_SWAP_ENDIAN (1 << 0)
-/* Controller needs 4x internal clock */
-#define QUADSPI_QUIRK_4X_INT_CLK (1 << 1)
-/*
- * TKT253890, Controller needs driver to fill txfifo till 16 byte to
- * trigger data transfer even though extern data will not transferred.
- */
-#define QUADSPI_QUIRK_TKT253890 (1 << 2)
-/* Controller cannot wake up from wait mode, TKT245618 */
-#define QUADSPI_QUIRK_TKT245618 (1 << 3)
-
-/* The registers */
-#define QUADSPI_MCR 0x00
-#define QUADSPI_MCR_RESERVED_SHIFT 16
-#define QUADSPI_MCR_RESERVED_MASK (0xF << QUADSPI_MCR_RESERVED_SHIFT)
-#define QUADSPI_MCR_MDIS_SHIFT 14
-#define QUADSPI_MCR_MDIS_MASK (1 << QUADSPI_MCR_MDIS_SHIFT)
-#define QUADSPI_MCR_CLR_TXF_SHIFT 11
-#define QUADSPI_MCR_CLR_TXF_MASK (1 << QUADSPI_MCR_CLR_TXF_SHIFT)
-#define QUADSPI_MCR_CLR_RXF_SHIFT 10
-#define QUADSPI_MCR_CLR_RXF_MASK (1 << QUADSPI_MCR_CLR_RXF_SHIFT)
-#define QUADSPI_MCR_DDR_EN_SHIFT 7
-#define QUADSPI_MCR_DDR_EN_MASK (1 << QUADSPI_MCR_DDR_EN_SHIFT)
-#define QUADSPI_MCR_END_CFG_SHIFT 2
-#define QUADSPI_MCR_END_CFG_MASK (3 << QUADSPI_MCR_END_CFG_SHIFT)
-#define QUADSPI_MCR_SWRSTHD_SHIFT 1
-#define QUADSPI_MCR_SWRSTHD_MASK (1 << QUADSPI_MCR_SWRSTHD_SHIFT)
-#define QUADSPI_MCR_SWRSTSD_SHIFT 0
-#define QUADSPI_MCR_SWRSTSD_MASK (1 << QUADSPI_MCR_SWRSTSD_SHIFT)
-
-#define QUADSPI_IPCR 0x08
-#define QUADSPI_IPCR_SEQID_SHIFT 24
-#define QUADSPI_IPCR_SEQID_MASK (0xF << QUADSPI_IPCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0CR 0x10
-#define QUADSPI_BUF1CR 0x14
-#define QUADSPI_BUF2CR 0x18
-#define QUADSPI_BUFXCR_INVALID_MSTRID 0xe
-
-#define QUADSPI_BUF3CR 0x1c
-#define QUADSPI_BUF3CR_ALLMST_SHIFT 31
-#define QUADSPI_BUF3CR_ALLMST_MASK (1 << QUADSPI_BUF3CR_ALLMST_SHIFT)
-#define QUADSPI_BUF3CR_ADATSZ_SHIFT 8
-#define QUADSPI_BUF3CR_ADATSZ_MASK (0xFF << QUADSPI_BUF3CR_ADATSZ_SHIFT)
-
-#define QUADSPI_BFGENCR 0x20
-#define QUADSPI_BFGENCR_PAR_EN_SHIFT 16
-#define QUADSPI_BFGENCR_PAR_EN_MASK (1 << (QUADSPI_BFGENCR_PAR_EN_SHIFT))
-#define QUADSPI_BFGENCR_SEQID_SHIFT 12
-#define QUADSPI_BFGENCR_SEQID_MASK (0xF << QUADSPI_BFGENCR_SEQID_SHIFT)
-
-#define QUADSPI_BUF0IND 0x30
-#define QUADSPI_BUF1IND 0x34
-#define QUADSPI_BUF2IND 0x38
-#define QUADSPI_SFAR 0x100
-
-#define QUADSPI_SMPR 0x108
-#define QUADSPI_SMPR_DDRSMP_SHIFT 16
-#define QUADSPI_SMPR_DDRSMP_MASK (7 << QUADSPI_SMPR_DDRSMP_SHIFT)
-#define QUADSPI_SMPR_FSDLY_SHIFT 6
-#define QUADSPI_SMPR_FSDLY_MASK (1 << QUADSPI_SMPR_FSDLY_SHIFT)
-#define QUADSPI_SMPR_FSPHS_SHIFT 5
-#define QUADSPI_SMPR_FSPHS_MASK (1 << QUADSPI_SMPR_FSPHS_SHIFT)
-#define QUADSPI_SMPR_HSENA_SHIFT 0
-#define QUADSPI_SMPR_HSENA_MASK (1 << QUADSPI_SMPR_HSENA_SHIFT)
-
-#define QUADSPI_RBSR 0x10c
-#define QUADSPI_RBSR_RDBFL_SHIFT 8
-#define QUADSPI_RBSR_RDBFL_MASK (0x3F << QUADSPI_RBSR_RDBFL_SHIFT)
-
-#define QUADSPI_RBCT 0x110
-#define QUADSPI_RBCT_WMRK_MASK 0x1F
-#define QUADSPI_RBCT_RXBRD_SHIFT 8
-#define QUADSPI_RBCT_RXBRD_USEIPS (0x1 << QUADSPI_RBCT_RXBRD_SHIFT)
-
-#define QUADSPI_TBSR 0x150
-#define QUADSPI_TBDR 0x154
-#define QUADSPI_SR 0x15c
-#define QUADSPI_SR_IP_ACC_SHIFT 1
-#define QUADSPI_SR_IP_ACC_MASK (0x1 << QUADSPI_SR_IP_ACC_SHIFT)
-#define QUADSPI_SR_AHB_ACC_SHIFT 2
-#define QUADSPI_SR_AHB_ACC_MASK (0x1 << QUADSPI_SR_AHB_ACC_SHIFT)
-
-#define QUADSPI_FR 0x160
-#define QUADSPI_FR_TFF_MASK 0x1
-
-#define QUADSPI_SFA1AD 0x180
-#define QUADSPI_SFA2AD 0x184
-#define QUADSPI_SFB1AD 0x188
-#define QUADSPI_SFB2AD 0x18c
-#define QUADSPI_RBDR 0x200
-
-#define QUADSPI_LUTKEY 0x300
-#define QUADSPI_LUTKEY_VALUE 0x5AF05AF0
-
-#define QUADSPI_LCKCR 0x304
-#define QUADSPI_LCKER_LOCK 0x1
-#define QUADSPI_LCKER_UNLOCK 0x2
-
-#define QUADSPI_RSER 0x164
-#define QUADSPI_RSER_TFIE (0x1 << 0)
-
-#define QUADSPI_LUT_BASE 0x310
-
-/*
- * The definition of the LUT register shows below:
- *
- * ---------------------------------------------------
- * | INSTR1 | PAD1 | OPRND1 | INSTR0 | PAD0 | OPRND0 |
- * ---------------------------------------------------
- */
-#define OPRND0_SHIFT 0
-#define PAD0_SHIFT 8
-#define INSTR0_SHIFT 10
-#define OPRND1_SHIFT 16
-
-/* Instruction set for the LUT register. */
-#define LUT_STOP 0
-#define LUT_CMD 1
-#define LUT_ADDR 2
-#define LUT_DUMMY 3
-#define LUT_MODE 4
-#define LUT_MODE2 5
-#define LUT_MODE4 6
-#define LUT_FSL_READ 7
-#define LUT_FSL_WRITE 8
-#define LUT_JMP_ON_CS 9
-#define LUT_ADDR_DDR 10
-#define LUT_MODE_DDR 11
-#define LUT_MODE2_DDR 12
-#define LUT_MODE4_DDR 13
-#define LUT_FSL_READ_DDR 14
-#define LUT_FSL_WRITE_DDR 15
-#define LUT_DATA_LEARN 16
-
-/*
- * The PAD definitions for LUT register.
- *
- * The pad stands for the lines number of IO[0:3].
- * For example, the Quad read need four IO lines, so you should
- * set LUT_PAD4 which means we use four IO lines.
- */
-#define LUT_PAD1 0
-#define LUT_PAD2 1
-#define LUT_PAD4 2
-
-/* Oprands for the LUT register. */
-#define ADDR24BIT 0x18
-#define ADDR32BIT 0x20
-
-/* Macros for constructing the LUT register. */
-#define LUT0(ins, pad, opr) \
- (((opr) << OPRND0_SHIFT) | ((LUT_##pad) << PAD0_SHIFT) | \
- ((LUT_##ins) << INSTR0_SHIFT))
-
-#define LUT1(ins, pad, opr) (LUT0(ins, pad, opr) << OPRND1_SHIFT)
-
-/* other macros for LUT register. */
-#define QUADSPI_LUT(x) (QUADSPI_LUT_BASE + (x) * 4)
-#define QUADSPI_LUT_NUM 64
-
-/* SEQID -- we can have 16 seqids at most. */
-#define SEQID_READ 0
-#define SEQID_WREN 1
-#define SEQID_WRDI 2
-#define SEQID_RDSR 3
-#define SEQID_SE 4
-#define SEQID_CHIP_ERASE 5
-#define SEQID_PP 6
-#define SEQID_RDID 7
-#define SEQID_WRSR 8
-#define SEQID_RDCR 9
-#define SEQID_EN4B 10
-#define SEQID_BRWR 11
-
-#define QUADSPI_MIN_IOMAP SZ_4M
-
-enum fsl_qspi_devtype {
- FSL_QUADSPI_VYBRID,
- FSL_QUADSPI_IMX6SX,
- FSL_QUADSPI_IMX7D,
- FSL_QUADSPI_IMX6UL,
- FSL_QUADSPI_LS1021A,
- FSL_QUADSPI_LS2080A,
-};
-
-struct fsl_qspi_devtype_data {
- enum fsl_qspi_devtype devtype;
- int rxfifo;
- int txfifo;
- int ahb_buf_size;
- int driver_data;
-};
-
-static const struct fsl_qspi_devtype_data vybrid_data = {
- .devtype = FSL_QUADSPI_VYBRID,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_SWAP_ENDIAN,
-};
-
-static const struct fsl_qspi_devtype_data imx6sx_data = {
- .devtype = FSL_QUADSPI_IMX6SX,
- .rxfifo = 128,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_4X_INT_CLK
- | QUADSPI_QUIRK_TKT245618,
-};
-
-static const struct fsl_qspi_devtype_data imx7d_data = {
- .devtype = FSL_QUADSPI_IMX7D,
- .rxfifo = 512,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890
- | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static const struct fsl_qspi_devtype_data imx6ul_data = {
- .devtype = FSL_QUADSPI_IMX6UL,
- .rxfifo = 128,
- .txfifo = 512,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890
- | QUADSPI_QUIRK_4X_INT_CLK,
-};
-
-static struct fsl_qspi_devtype_data ls1021a_data = {
- .devtype = FSL_QUADSPI_LS1021A,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = 0,
-};
-
-static const struct fsl_qspi_devtype_data ls2080a_data = {
- .devtype = FSL_QUADSPI_LS2080A,
- .rxfifo = 128,
- .txfifo = 64,
- .ahb_buf_size = 1024,
- .driver_data = QUADSPI_QUIRK_TKT253890,
-};
-
-
-#define FSL_QSPI_MAX_CHIP 4
-struct fsl_qspi {
- struct spi_nor nor[FSL_QSPI_MAX_CHIP];
- void __iomem *iobase;
- void __iomem *ahb_addr;
- u32 memmap_phy;
- u32 memmap_offs;
- u32 memmap_len;
- struct clk *clk, *clk_en;
- struct device *dev;
- struct completion c;
- const struct fsl_qspi_devtype_data *devtype_data;
- u32 nor_size;
- u32 nor_num;
- u32 clk_rate;
- unsigned int chip_base_addr; /* We may support two chips. */
- bool has_second_chip;
- bool big_endian;
- struct mutex lock;
- struct pm_qos_request pm_qos_req;
-};
-
-static inline int needs_swap_endian(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_SWAP_ENDIAN;
-}
-
-static inline int needs_4x_clock(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_4X_INT_CLK;
-}
-
-static inline int needs_fill_txfifo(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT253890;
-}
-
-static inline int needs_wakeup_wait_mode(struct fsl_qspi *q)
-{
- return q->devtype_data->driver_data & QUADSPI_QUIRK_TKT245618;
-}
-
-/*
- * R/W functions for big- or little-endian registers:
- * The qSPI controller's endian is independent of the CPU core's endian.
- * So far, although the CPU core is little-endian but the qSPI have two
- * versions for big-endian and little-endian.
- */
-static void qspi_writel(struct fsl_qspi *q, u32 val, void __iomem *addr)
-{
- if (q->big_endian)
- iowrite32be(val, addr);
- else
- iowrite32(val, addr);
-}
-
-static u32 qspi_readl(struct fsl_qspi *q, void __iomem *addr)
-{
- if (q->big_endian)
- return ioread32be(addr);
- else
- return ioread32(addr);
-}
-
-/*
- * An IC bug makes us to re-arrange the 32-bit data.
- * The following chips, such as IMX6SLX, have fixed this bug.
- */
-static inline u32 fsl_qspi_endian_xchg(struct fsl_qspi *q, u32 a)
-{
- return needs_swap_endian(q) ? __swab32(a) : a;
-}
-
-static inline void fsl_qspi_unlock_lut(struct fsl_qspi *q)
-{
- qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
- qspi_writel(q, QUADSPI_LCKER_UNLOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static inline void fsl_qspi_lock_lut(struct fsl_qspi *q)
-{
- qspi_writel(q, QUADSPI_LUTKEY_VALUE, q->iobase + QUADSPI_LUTKEY);
- qspi_writel(q, QUADSPI_LCKER_LOCK, q->iobase + QUADSPI_LCKCR);
-}
-
-static irqreturn_t fsl_qspi_irq_handler(int irq, void *dev_id)
-{
- struct fsl_qspi *q = dev_id;
- u32 reg;
-
- /* clear interrupt */
- reg = qspi_readl(q, q->iobase + QUADSPI_FR);
- qspi_writel(q, reg, q->iobase + QUADSPI_FR);
-
- if (reg & QUADSPI_FR_TFF_MASK)
- complete(&q->c);
-
- dev_dbg(q->dev, "QUADSPI_FR : 0x%.8x:0x%.8x\n", q->chip_base_addr, reg);
- return IRQ_HANDLED;
-}
-
-static void fsl_qspi_init_lut(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- int rxfifo = q->devtype_data->rxfifo;
- u32 lut_base;
- int i;
-
- struct spi_nor *nor = &q->nor[0];
- u8 addrlen = (nor->addr_width == 3) ? ADDR24BIT : ADDR32BIT;
- u8 read_op = nor->read_opcode;
- u8 read_dm = nor->read_dummy;
-
- fsl_qspi_unlock_lut(q);
-
- /* Clear all the LUT table */
- for (i = 0; i < QUADSPI_LUT_NUM; i++)
- qspi_writel(q, 0, base + QUADSPI_LUT_BASE + i * 4);
-
- /* Read */
- lut_base = SEQID_READ * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, read_op) | LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
- qspi_writel(q, LUT0(DUMMY, PAD1, read_dm) |
- LUT1(FSL_READ, PAD4, rxfifo),
- base + QUADSPI_LUT(lut_base + 1));
-
- /* Write enable */
- lut_base = SEQID_WREN * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WREN),
- base + QUADSPI_LUT(lut_base));
-
- /* Page Program */
- lut_base = SEQID_PP * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, nor->program_opcode) |
- LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
- qspi_writel(q, LUT0(FSL_WRITE, PAD1, 0),
- base + QUADSPI_LUT(lut_base + 1));
-
- /* Read Status */
- lut_base = SEQID_RDSR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDSR) |
- LUT1(FSL_READ, PAD1, 0x1),
- base + QUADSPI_LUT(lut_base));
-
- /* Erase a sector */
- lut_base = SEQID_SE * 4;
-
- qspi_writel(q, LUT0(CMD, PAD1, nor->erase_opcode) |
- LUT1(ADDR, PAD1, addrlen),
- base + QUADSPI_LUT(lut_base));
-
- /* Erase the whole chip */
- lut_base = SEQID_CHIP_ERASE * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_CHIP_ERASE),
- base + QUADSPI_LUT(lut_base));
-
- /* READ ID */
- lut_base = SEQID_RDID * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDID) |
- LUT1(FSL_READ, PAD1, 0x8),
- base + QUADSPI_LUT(lut_base));
-
- /* Write Register */
- lut_base = SEQID_WRSR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRSR) |
- LUT1(FSL_WRITE, PAD1, 0x2),
- base + QUADSPI_LUT(lut_base));
-
- /* Read Configuration Register */
- lut_base = SEQID_RDCR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_RDCR) |
- LUT1(FSL_READ, PAD1, 0x1),
- base + QUADSPI_LUT(lut_base));
-
- /* Write disable */
- lut_base = SEQID_WRDI * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_WRDI),
- base + QUADSPI_LUT(lut_base));
-
- /* Enter 4 Byte Mode (Micron) */
- lut_base = SEQID_EN4B * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_EN4B),
- base + QUADSPI_LUT(lut_base));
-
- /* Enter 4 Byte Mode (Spansion) */
- lut_base = SEQID_BRWR * 4;
- qspi_writel(q, LUT0(CMD, PAD1, SPINOR_OP_BRWR),
- base + QUADSPI_LUT(lut_base));
-
- fsl_qspi_lock_lut(q);
-}
-
-/* Get the SEQID for the command */
-static int fsl_qspi_get_seqid(struct fsl_qspi *q, u8 cmd)
-{
- switch (cmd) {
- case SPINOR_OP_READ_1_1_4:
- case SPINOR_OP_READ_1_1_4_4B:
- return SEQID_READ;
- case SPINOR_OP_WREN:
- return SEQID_WREN;
- case SPINOR_OP_WRDI:
- return SEQID_WRDI;
- case SPINOR_OP_RDSR:
- return SEQID_RDSR;
- case SPINOR_OP_SE:
- return SEQID_SE;
- case SPINOR_OP_CHIP_ERASE:
- return SEQID_CHIP_ERASE;
- case SPINOR_OP_PP:
- return SEQID_PP;
- case SPINOR_OP_RDID:
- return SEQID_RDID;
- case SPINOR_OP_WRSR:
- return SEQID_WRSR;
- case SPINOR_OP_RDCR:
- return SEQID_RDCR;
- case SPINOR_OP_EN4B:
- return SEQID_EN4B;
- case SPINOR_OP_BRWR:
- return SEQID_BRWR;
- default:
- if (cmd == q->nor[0].erase_opcode)
- return SEQID_SE;
- dev_err(q->dev, "Unsupported cmd 0x%.2x\n", cmd);
- break;
- }
- return -EINVAL;
-}
-
-static int
-fsl_qspi_runcmd(struct fsl_qspi *q, u8 cmd, unsigned int addr, int len)
-{
- void __iomem *base = q->iobase;
- int seqid;
- u32 reg, reg2;
- int err;
-
- init_completion(&q->c);
- dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len:%d, cmd:%.2x\n",
- q->chip_base_addr, addr, len, cmd);
-
- /* save the reg */
- reg = qspi_readl(q, base + QUADSPI_MCR);
-
- qspi_writel(q, q->memmap_phy + q->chip_base_addr + addr,
- base + QUADSPI_SFAR);
- qspi_writel(q, QUADSPI_RBCT_WMRK_MASK | QUADSPI_RBCT_RXBRD_USEIPS,
- base + QUADSPI_RBCT);
- qspi_writel(q, reg | QUADSPI_MCR_CLR_RXF_MASK, base + QUADSPI_MCR);
-
- do {
- reg2 = qspi_readl(q, base + QUADSPI_SR);
- if (reg2 & (QUADSPI_SR_IP_ACC_MASK | QUADSPI_SR_AHB_ACC_MASK)) {
- udelay(1);
- dev_dbg(q->dev, "The controller is busy, 0x%x\n", reg2);
- continue;
- }
- break;
- } while (1);
-
- /* trigger the LUT now */
- seqid = fsl_qspi_get_seqid(q, cmd);
- if (seqid < 0)
- return seqid;
-
- qspi_writel(q, (seqid << QUADSPI_IPCR_SEQID_SHIFT) | len,
- base + QUADSPI_IPCR);
-
- /* Wait for the interrupt. */
- if (!wait_for_completion_timeout(&q->c, msecs_to_jiffies(1000))) {
- dev_err(q->dev,
- "cmd 0x%.2x timeout, addr@%.8x, FR:0x%.8x, SR:0x%.8x\n",
- cmd, addr, qspi_readl(q, base + QUADSPI_FR),
- qspi_readl(q, base + QUADSPI_SR));
- err = -ETIMEDOUT;
- } else {
- err = 0;
- }
-
- /* restore the MCR */
- qspi_writel(q, reg, base + QUADSPI_MCR);
-
- return err;
-}
-
-/* Read out the data from the QUADSPI_RBDR buffer registers. */
-static void fsl_qspi_read_data(struct fsl_qspi *q, int len, u8 *rxbuf)
-{
- u32 tmp;
- int i = 0;
-
- while (len > 0) {
- tmp = qspi_readl(q, q->iobase + QUADSPI_RBDR + i * 4);
- tmp = fsl_qspi_endian_xchg(q, tmp);
- dev_dbg(q->dev, "chip addr:0x%.8x, rcv:0x%.8x\n",
- q->chip_base_addr, tmp);
-
- if (len >= 4) {
- *((u32 *)rxbuf) = tmp;
- rxbuf += 4;
- } else {
- memcpy(rxbuf, &tmp, len);
- break;
- }
-
- len -= 4;
- i++;
- }
-}
-
-/*
- * If we have changed the content of the flash by writing or erasing,
- * we need to invalidate the AHB buffer. If we do not do so, we may read out
- * the wrong data. The spec tells us reset the AHB domain and Serial Flash
- * domain at the same time.
- */
-static inline void fsl_qspi_invalid(struct fsl_qspi *q)
-{
- u32 reg;
-
- reg = qspi_readl(q, q->iobase + QUADSPI_MCR);
- reg |= QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK;
- qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-
- /*
- * The minimum delay : 1 AHB + 2 SFCK clocks.
- * Delay 1 us is enough.
- */
- udelay(1);
-
- reg &= ~(QUADSPI_MCR_SWRSTHD_MASK | QUADSPI_MCR_SWRSTSD_MASK);
- qspi_writel(q, reg, q->iobase + QUADSPI_MCR);
-}
-
-static ssize_t fsl_qspi_nor_write(struct fsl_qspi *q, struct spi_nor *nor,
- u8 opcode, unsigned int to, u32 *txbuf,
- unsigned count)
-{
- int ret, i, j;
- u32 tmp;
-
- dev_dbg(q->dev, "to 0x%.8x:0x%.8x, len : %d\n",
- q->chip_base_addr, to, count);
-
- /* clear the TX FIFO. */
- tmp = qspi_readl(q, q->iobase + QUADSPI_MCR);
- qspi_writel(q, tmp | QUADSPI_MCR_CLR_TXF_MASK, q->iobase + QUADSPI_MCR);
-
- /* fill the TX data to the FIFO */
- for (j = 0, i = ((count + 3) / 4); j < i; j++) {
- tmp = fsl_qspi_endian_xchg(q, *txbuf);
- qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
- txbuf++;
- }
-
- /* fill the TXFIFO upto 16 bytes for i.MX7d */
- if (needs_fill_txfifo(q))
- for (; i < 4; i++)
- qspi_writel(q, tmp, q->iobase + QUADSPI_TBDR);
-
- /* Trigger it */
- ret = fsl_qspi_runcmd(q, opcode, to, count);
-
- if (ret == 0)
- return count;
-
- return ret;
-}
-
-static void fsl_qspi_set_map_addr(struct fsl_qspi *q)
-{
- int nor_size = q->nor_size;
- void __iomem *base = q->iobase;
-
- qspi_writel(q, nor_size + q->memmap_phy, base + QUADSPI_SFA1AD);
- qspi_writel(q, nor_size * 2 + q->memmap_phy, base + QUADSPI_SFA2AD);
- qspi_writel(q, nor_size * 3 + q->memmap_phy, base + QUADSPI_SFB1AD);
- qspi_writel(q, nor_size * 4 + q->memmap_phy, base + QUADSPI_SFB2AD);
-}
-
-/*
- * There are two different ways to read out the data from the flash:
- * the "IP Command Read" and the "AHB Command Read".
- *
- * The IC guy suggests we use the "AHB Command Read" which is faster
- * then the "IP Command Read". (What's more is that there is a bug in
- * the "IP Command Read" in the Vybrid.)
- *
- * After we set up the registers for the "AHB Command Read", we can use
- * the memcpy to read the data directly. A "missed" access to the buffer
- * causes the controller to clear the buffer, and use the sequence pointed
- * by the QUADSPI_BFGENCR[SEQID] to initiate a read from the flash.
- */
-static int fsl_qspi_init_ahb_read(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- int seqid;
-
- /* AHB configuration for access buffer 0/1/2 .*/
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF0CR);
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF1CR);
- qspi_writel(q, QUADSPI_BUFXCR_INVALID_MSTRID, base + QUADSPI_BUF2CR);
- /*
- * Set ADATSZ with the maximum AHB buffer size to improve the
- * read performance.
- */
- qspi_writel(q, QUADSPI_BUF3CR_ALLMST_MASK |
- ((q->devtype_data->ahb_buf_size / 8)
- << QUADSPI_BUF3CR_ADATSZ_SHIFT),
- base + QUADSPI_BUF3CR);
-
- /* We only use the buffer3 */
- qspi_writel(q, 0, base + QUADSPI_BUF0IND);
- qspi_writel(q, 0, base + QUADSPI_BUF1IND);
- qspi_writel(q, 0, base + QUADSPI_BUF2IND);
-
- /* Set the default lut sequence for AHB Read. */
- seqid = fsl_qspi_get_seqid(q, q->nor[0].read_opcode);
- if (seqid < 0)
- return seqid;
-
- qspi_writel(q, seqid << QUADSPI_BFGENCR_SEQID_SHIFT,
- q->iobase + QUADSPI_BFGENCR);
-
- return 0;
-}
-
-/* This function was used to prepare and enable QSPI clock */
-static int fsl_qspi_clk_prep_enable(struct fsl_qspi *q)
-{
- int ret;
-
- ret = clk_prepare_enable(q->clk_en);
- if (ret)
- return ret;
-
- ret = clk_prepare_enable(q->clk);
- if (ret) {
- clk_disable_unprepare(q->clk_en);
- return ret;
- }
-
- if (needs_wakeup_wait_mode(q))
- pm_qos_add_request(&q->pm_qos_req, PM_QOS_CPU_DMA_LATENCY, 0);
-
- return 0;
-}
-
-/* This function was used to disable and unprepare QSPI clock */
-static void fsl_qspi_clk_disable_unprep(struct fsl_qspi *q)
-{
- if (needs_wakeup_wait_mode(q))
- pm_qos_remove_request(&q->pm_qos_req);
-
- clk_disable_unprepare(q->clk);
- clk_disable_unprepare(q->clk_en);
-
-}
-
-/* We use this function to do some basic init for spi_nor_scan(). */
-static int fsl_qspi_nor_setup(struct fsl_qspi *q)
-{
- void __iomem *base = q->iobase;
- u32 reg;
- int ret;
-
- /* disable and unprepare clock to avoid glitch pass to controller */
- fsl_qspi_clk_disable_unprep(q);
-
- /* the default frequency, we will change it in the future. */
- ret = clk_set_rate(q->clk, 66000000);
- if (ret)
- return ret;
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- /* Reset the module */
- qspi_writel(q, QUADSPI_MCR_SWRSTSD_MASK | QUADSPI_MCR_SWRSTHD_MASK,
- base + QUADSPI_MCR);
- udelay(1);
-
- /* Init the LUT table. */
- fsl_qspi_init_lut(q);
-
- /* Disable the module */
- qspi_writel(q, QUADSPI_MCR_MDIS_MASK | QUADSPI_MCR_RESERVED_MASK,
- base + QUADSPI_MCR);
-
- reg = qspi_readl(q, base + QUADSPI_SMPR);
- qspi_writel(q, reg & ~(QUADSPI_SMPR_FSDLY_MASK
- | QUADSPI_SMPR_FSPHS_MASK
- | QUADSPI_SMPR_HSENA_MASK
- | QUADSPI_SMPR_DDRSMP_MASK), base + QUADSPI_SMPR);
-
- /* Enable the module */
- qspi_writel(q, QUADSPI_MCR_RESERVED_MASK | QUADSPI_MCR_END_CFG_MASK,
- base + QUADSPI_MCR);
-
- /* clear all interrupt status */
- qspi_writel(q, 0xffffffff, q->iobase + QUADSPI_FR);
-
- /* enable the interrupt */
- qspi_writel(q, QUADSPI_RSER_TFIE, q->iobase + QUADSPI_RSER);
-
- return 0;
-}
-
-static int fsl_qspi_nor_setup_last(struct fsl_qspi *q)
-{
- unsigned long rate = q->clk_rate;
- int ret;
-
- if (needs_4x_clock(q))
- rate *= 4;
-
- /* disable and unprepare clock to avoid glitch pass to controller */
- fsl_qspi_clk_disable_unprep(q);
-
- ret = clk_set_rate(q->clk, rate);
- if (ret)
- return ret;
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- /* Init the LUT table again. */
- fsl_qspi_init_lut(q);
-
- /* Init for AHB read */
- return fsl_qspi_init_ahb_read(q);
-}
-
-static const struct of_device_id fsl_qspi_dt_ids[] = {
- { .compatible = "fsl,vf610-qspi", .data = &vybrid_data, },
- { .compatible = "fsl,imx6sx-qspi", .data = &imx6sx_data, },
- { .compatible = "fsl,imx7d-qspi", .data = &imx7d_data, },
- { .compatible = "fsl,imx6ul-qspi", .data = &imx6ul_data, },
- { .compatible = "fsl,ls1021a-qspi", .data = (void *)&ls1021a_data, },
- { .compatible = "fsl,ls2080a-qspi", .data = &ls2080a_data, },
- { /* sentinel */ }
-};
-MODULE_DEVICE_TABLE(of, fsl_qspi_dt_ids);
-
-static void fsl_qspi_set_base_addr(struct fsl_qspi *q, struct spi_nor *nor)
-{
- q->chip_base_addr = q->nor_size * (nor - q->nor);
-}
-
-static int fsl_qspi_read_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
- int ret;
- struct fsl_qspi *q = nor->priv;
-
- ret = fsl_qspi_runcmd(q, opcode, 0, len);
- if (ret)
- return ret;
-
- fsl_qspi_read_data(q, len, buf);
- return 0;
-}
-
-static int fsl_qspi_write_reg(struct spi_nor *nor, u8 opcode, u8 *buf, int len)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- if (!buf) {
- ret = fsl_qspi_runcmd(q, opcode, 0, 1);
- if (ret)
- return ret;
-
- if (opcode == SPINOR_OP_CHIP_ERASE)
- fsl_qspi_invalid(q);
-
- } else if (len > 0) {
- ret = fsl_qspi_nor_write(q, nor, opcode, 0,
- (u32 *)buf, len);
- if (ret > 0)
- return 0;
- } else {
- dev_err(q->dev, "invalid cmd %d\n", opcode);
- ret = -EINVAL;
- }
-
- return ret;
-}
-
-static ssize_t fsl_qspi_write(struct spi_nor *nor, loff_t to,
- size_t len, const u_char *buf)
-{
- struct fsl_qspi *q = nor->priv;
- ssize_t ret = fsl_qspi_nor_write(q, nor, nor->program_opcode, to,
- (u32 *)buf, len);
-
- /* invalid the data in the AHB buffer. */
- fsl_qspi_invalid(q);
- return ret;
-}
-
-static ssize_t fsl_qspi_read(struct spi_nor *nor, loff_t from,
- size_t len, u_char *buf)
-{
- struct fsl_qspi *q = nor->priv;
- u8 cmd = nor->read_opcode;
-
- /* if necessary,ioremap buffer before AHB read, */
- if (!q->ahb_addr) {
- q->memmap_offs = q->chip_base_addr + from;
- q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
-
- q->ahb_addr = ioremap_nocache(
- q->memmap_phy + q->memmap_offs,
- q->memmap_len);
- if (!q->ahb_addr) {
- dev_err(q->dev, "ioremap failed\n");
- return -ENOMEM;
- }
- /* ioremap if the data requested is out of range */
- } else if (q->chip_base_addr + from < q->memmap_offs
- || q->chip_base_addr + from + len >
- q->memmap_offs + q->memmap_len) {
- iounmap(q->ahb_addr);
-
- q->memmap_offs = q->chip_base_addr + from;
- q->memmap_len = len > QUADSPI_MIN_IOMAP ? len : QUADSPI_MIN_IOMAP;
- q->ahb_addr = ioremap_nocache(
- q->memmap_phy + q->memmap_offs,
- q->memmap_len);
- if (!q->ahb_addr) {
- dev_err(q->dev, "ioremap failed\n");
- return -ENOMEM;
- }
- }
-
- dev_dbg(q->dev, "cmd [%x],read from %p, len:%zd\n",
- cmd, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
- len);
-
- /* Read out the data directly from the AHB buffer.*/
- memcpy(buf, q->ahb_addr + q->chip_base_addr + from - q->memmap_offs,
- len);
-
- return len;
-}
-
-static int fsl_qspi_erase(struct spi_nor *nor, loff_t offs)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- dev_dbg(nor->dev, "%dKiB at 0x%08x:0x%08x\n",
- nor->mtd.erasesize / 1024, q->chip_base_addr, (u32)offs);
-
- ret = fsl_qspi_runcmd(q, nor->erase_opcode, offs, 0);
- if (ret)
- return ret;
-
- fsl_qspi_invalid(q);
- return 0;
-}
-
-static int fsl_qspi_prep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
- struct fsl_qspi *q = nor->priv;
- int ret;
-
- mutex_lock(&q->lock);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- goto err_mutex;
-
- fsl_qspi_set_base_addr(q, nor);
- return 0;
-
-err_mutex:
- mutex_unlock(&q->lock);
- return ret;
-}
-
-static void fsl_qspi_unprep(struct spi_nor *nor, enum spi_nor_ops ops)
-{
- struct fsl_qspi *q = nor->priv;
-
- fsl_qspi_clk_disable_unprep(q);
- mutex_unlock(&q->lock);
-}
-
-static int fsl_qspi_probe(struct platform_device *pdev)
-{
- const struct spi_nor_hwcaps hwcaps = {
- .mask = SNOR_HWCAPS_READ_1_1_4 |
- SNOR_HWCAPS_PP,
- };
- struct device_node *np = pdev->dev.of_node;
- struct device *dev = &pdev->dev;
- struct fsl_qspi *q;
- struct resource *res;
- struct spi_nor *nor;
- struct mtd_info *mtd;
- int ret, i = 0;
-
- q = devm_kzalloc(dev, sizeof(*q), GFP_KERNEL);
- if (!q)
- return -ENOMEM;
-
- q->nor_num = of_get_child_count(dev->of_node);
- if (!q->nor_num || q->nor_num > FSL_QSPI_MAX_CHIP)
- return -ENODEV;
-
- q->dev = dev;
- q->devtype_data = of_device_get_match_data(dev);
- if (!q->devtype_data)
- return -ENODEV;
- platform_set_drvdata(pdev, q);
-
- /* find the resources */
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "QuadSPI");
- q->iobase = devm_ioremap_resource(dev, res);
- if (IS_ERR(q->iobase))
- return PTR_ERR(q->iobase);
-
- q->big_endian = of_property_read_bool(np, "big-endian");
- res = platform_get_resource_byname(pdev, IORESOURCE_MEM,
- "QuadSPI-memory");
- if (!devm_request_mem_region(dev, res->start, resource_size(res),
- res->name)) {
- dev_err(dev, "can't request region for resource %pR\n", res);
- return -EBUSY;
- }
-
- q->memmap_phy = res->start;
-
- /* find the clocks */
- q->clk_en = devm_clk_get(dev, "qspi_en");
- if (IS_ERR(q->clk_en))
- return PTR_ERR(q->clk_en);
-
- q->clk = devm_clk_get(dev, "qspi");
- if (IS_ERR(q->clk))
- return PTR_ERR(q->clk);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret) {
- dev_err(dev, "can not enable the clock\n");
- goto clk_failed;
- }
-
- /* find the irq */
- ret = platform_get_irq(pdev, 0);
- if (ret < 0) {
- dev_err(dev, "failed to get the irq: %d\n", ret);
- goto irq_failed;
- }
-
- ret = devm_request_irq(dev, ret,
- fsl_qspi_irq_handler, 0, pdev->name, q);
- if (ret) {
- dev_err(dev, "failed to request irq: %d\n", ret);
- goto irq_failed;
- }
-
- ret = fsl_qspi_nor_setup(q);
- if (ret)
- goto irq_failed;
-
- if (of_get_property(np, "fsl,qspi-has-second-chip", NULL))
- q->has_second_chip = true;
-
- mutex_init(&q->lock);
-
- /* iterate the subnodes. */
- for_each_available_child_of_node(dev->of_node, np) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
-
- nor = &q->nor[i];
- mtd = &nor->mtd;
-
- nor->dev = dev;
- spi_nor_set_flash_node(nor, np);
- nor->priv = q;
-
- if (q->nor_num > 1 && !mtd->name) {
- int spiflash_idx;
-
- ret = of_property_read_u32(np, "reg", &spiflash_idx);
- if (!ret) {
- mtd->name = devm_kasprintf(dev, GFP_KERNEL,
- "%s-%d",
- dev_name(dev),
- spiflash_idx);
- if (!mtd->name) {
- ret = -ENOMEM;
- goto mutex_failed;
- }
- } else {
- dev_warn(dev, "reg property is missing\n");
- }
- }
-
- /* fill the hooks */
- nor->read_reg = fsl_qspi_read_reg;
- nor->write_reg = fsl_qspi_write_reg;
- nor->read = fsl_qspi_read;
- nor->write = fsl_qspi_write;
- nor->erase = fsl_qspi_erase;
-
- nor->prepare = fsl_qspi_prep;
- nor->unprepare = fsl_qspi_unprep;
-
- ret = of_property_read_u32(np, "spi-max-frequency",
- &q->clk_rate);
- if (ret < 0)
- goto mutex_failed;
-
- /* set the chip address for READID */
- fsl_qspi_set_base_addr(q, nor);
-
- ret = spi_nor_scan(nor, NULL, &hwcaps);
- if (ret)
- goto mutex_failed;
-
- ret = mtd_device_register(mtd, NULL, 0);
- if (ret)
- goto mutex_failed;
-
- /* Set the correct NOR size now. */
- if (q->nor_size == 0) {
- q->nor_size = mtd->size;
-
- /* Map the SPI NOR to accessiable address */
- fsl_qspi_set_map_addr(q);
- }
-
- /*
- * The TX FIFO is 64 bytes in the Vybrid, but the Page Program
- * may writes 265 bytes per time. The write is working in the
- * unit of the TX FIFO, not in the unit of the SPI NOR's page
- * size.
- *
- * So shrink the spi_nor->page_size if it is larger then the
- * TX FIFO.
- */
- if (nor->page_size > q->devtype_data->txfifo)
- nor->page_size = q->devtype_data->txfifo;
-
- i++;
- }
-
- /* finish the rest init. */
- ret = fsl_qspi_nor_setup_last(q);
- if (ret)
- goto last_init_failed;
-
- fsl_qspi_clk_disable_unprep(q);
- return 0;
-
-last_init_failed:
- for (i = 0; i < q->nor_num; i++) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
- mtd_device_unregister(&q->nor[i].mtd);
- }
-mutex_failed:
- mutex_destroy(&q->lock);
-irq_failed:
- fsl_qspi_clk_disable_unprep(q);
-clk_failed:
- dev_err(dev, "Freescale QuadSPI probe failed\n");
- return ret;
-}
-
-static int fsl_qspi_remove(struct platform_device *pdev)
-{
- struct fsl_qspi *q = platform_get_drvdata(pdev);
- int i;
-
- for (i = 0; i < q->nor_num; i++) {
- /* skip the holes */
- if (!q->has_second_chip)
- i *= 2;
- mtd_device_unregister(&q->nor[i].mtd);
- }
-
- /* disable the hardware */
- qspi_writel(q, QUADSPI_MCR_MDIS_MASK, q->iobase + QUADSPI_MCR);
- qspi_writel(q, 0x0, q->iobase + QUADSPI_RSER);
-
- mutex_destroy(&q->lock);
-
- if (q->ahb_addr)
- iounmap(q->ahb_addr);
-
- return 0;
-}
-
-static int fsl_qspi_suspend(struct platform_device *pdev, pm_message_t state)
-{
- return 0;
-}
-
-static int fsl_qspi_resume(struct platform_device *pdev)
-{
- int ret;
- struct fsl_qspi *q = platform_get_drvdata(pdev);
-
- ret = fsl_qspi_clk_prep_enable(q);
- if (ret)
- return ret;
-
- fsl_qspi_nor_setup(q);
- fsl_qspi_set_map_addr(q);
- fsl_qspi_nor_setup_last(q);
-
- fsl_qspi_clk_disable_unprep(q);
-
- return 0;
-}
-
-static struct platform_driver fsl_qspi_driver = {
- .driver = {
- .name = "fsl-quadspi",
- .of_match_table = fsl_qspi_dt_ids,
- },
- .probe = fsl_qspi_probe,
- .remove = fsl_qspi_remove,
- .suspend = fsl_qspi_suspend,
- .resume = fsl_qspi_resume,
-};
-module_platform_driver(fsl_qspi_driver);
-
-MODULE_DESCRIPTION("Freescale QuadSPI Controller Driver");
-MODULE_AUTHOR("Freescale Semiconductor Inc.");
-MODULE_LICENSE("GPL v2");