@@ -290,25 +290,15 @@ static void spi_gpio_cleanup(struct spi_device *spi)
* floating signals. (A weak pulldown would save power too, but many
* drivers expect to see all-ones data as the no slave "response".)
*/
-static int spi_gpio_request(struct device *dev,
- struct spi_gpio *spi_gpio,
- u16 *mflags)
+static int spi_gpio_request(struct device *dev, struct spi_gpio *spi_gpio)
{
spi_gpio->mosi = devm_gpiod_get_optional(dev, "mosi", GPIOD_OUT_LOW);
if (IS_ERR(spi_gpio->mosi))
return PTR_ERR(spi_gpio->mosi);
- if (!spi_gpio->mosi)
- /* HW configuration without MOSI pin */
- *mflags |= SPI_MASTER_NO_TX;
spi_gpio->miso = devm_gpiod_get_optional(dev, "miso", GPIOD_IN);
if (IS_ERR(spi_gpio->miso))
return PTR_ERR(spi_gpio->miso);
- /*
- * No setting SPI_MASTER_NO_RX here - if there is only a MOSI
- * pin connected the host can still do RX by changing the
- * direction of the line.
- */
spi_gpio->sck = devm_gpiod_get(dev, "sck", GPIOD_OUT_LOW);
if (IS_ERR(spi_gpio->sck))
@@ -382,7 +372,6 @@ static int spi_gpio_probe(struct platform_device *pdev)
struct device *dev = &pdev->dev;
struct spi_bitbang *bb;
const struct of_device_id *of_id;
- u16 master_flags = 0;
of_id = of_match_device(spi_gpio_dt_ids, &pdev->dev);
@@ -404,14 +393,23 @@ static int spi_gpio_probe(struct platform_device *pdev)
spi_gpio->pdev = pdev;
- status = spi_gpio_request(dev, spi_gpio, &master_flags);
+ status = spi_gpio_request(dev, spi_gpio);
if (status)
return status;
master->bits_per_word_mask = SPI_BPW_RANGE_MASK(1, 32);
master->mode_bits = SPI_3WIRE | SPI_3WIRE_HIZ | SPI_CPHA | SPI_CPOL |
SPI_CS_HIGH;
- master->flags = master_flags;
+ if (!spi_gpio->mosi) {
+ /* HW configuration without MOSI pin
+ *
+ * No setting SPI_MASTER_NO_RX here - if there is only
+ * a MOSI pin connected the host can still do RX by
+ * changing the direction of the line.
+ */
+ master->flags = SPI_MASTER_NO_TX;
+ }
+
master->bus_num = pdev->id;
master->setup = spi_gpio_setup;
master->cleanup = spi_gpio_cleanup;
@@ -421,7 +419,7 @@ static int spi_gpio_probe(struct platform_device *pdev)
bb->chipselect = spi_gpio_chipselect;
bb->set_line_direction = spi_gpio_set_direction;
- if (master_flags & SPI_MASTER_NO_TX) {
+ if (master->flags & SPI_MASTER_NO_TX) {
bb->txrx_word[SPI_MODE_0] = spi_gpio_spec_txrx_word_mode0;
bb->txrx_word[SPI_MODE_1] = spi_gpio_spec_txrx_word_mode1;
bb->txrx_word[SPI_MODE_2] = spi_gpio_spec_txrx_word_mode2;
The logic of setting mflags in spi_gpio_request() is very simple and there isn't much benefit in having it in that function. Move all of that code outside into spi_gpio_probe() in order to simplify things. Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com> Cc: Mark Brown <broonie@kernel.org> Cc: Chris Healy <cphealy@gmail.com> Cc: linux-spi@vger.kernel.org Cc: linux-kernel@vger.kernel.org --- drivers/spi/spi-gpio.c | 28 +++++++++++++--------------- 1 file changed, 13 insertions(+), 15 deletions(-)