[v2,2/2] spi: cadence-quadpsi: Add support for the Cadence QSPI controller

Commit Message

Ramuthevar,Vadivel MuruganX Oct. 30, 2019, 8:11 a.m. UTC

From: Ramuthevar Vadivel Murugan <[e-mail]>

Add support for the Cadence QSPI controller. This controller is
present in the Intel Lightning Mountain(LGM) SoCs, Altera and TI SoCs.
This driver has been tested on the Intel LGM SoCs.

This driver does not support generic SPI and also the implementation
only supports spi-mem interface to replace the existing driver in
mtd/spi-nor/cadence-quadspi.c, the existing driver only support SPI-NOR
flash memory.

Signed-off-by: Ramuthevar Vadivel Murugan <[e-mail]>
---
 drivers/spi/Kconfig               |   10 +
 drivers/spi/Makefile              |    1 +
 drivers/spi/spi-cadence-quadspi.c | 1290 +++++++++++++++++++++++++++++++++++++
 drivers/spi/spi-cadence-quadspi.h |  272 ++++++++
 4 files changed, 1573 insertions(+)
 create mode 100644 drivers/spi/spi-cadence-quadspi.c
 create mode 100644 drivers/spi/spi-cadence-quadspi.h

Comments

Vignesh Raghavendra Nov. 7, 2019, 5:44 a.m. UTC | #1

On 30/10/19 1:41 PM, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <[e-mail]>
> 
> Add support for the Cadence QSPI controller. This controller is
> present in the Intel Lightning Mountain(LGM) SoCs, Altera and TI SoCs.
> This driver has been tested on the Intel LGM SoCs.
> 
> This driver does not support generic SPI and also the implementation
> only supports spi-mem interface to replace the existing driver in
> mtd/spi-nor/cadence-quadspi.c, the existing driver only support SPI-NOR
> flash memory.
> 
> Signed-off-by: Ramuthevar Vadivel Murugan <[e-mail]>
> ---
>  drivers/spi/Kconfig               |   10 +
>  drivers/spi/Makefile              |    1 +
>  drivers/spi/spi-cadence-quadspi.c | 1290 +++++++++++++++++++++++++++++++++++++
>  drivers/spi/spi-cadence-quadspi.h |  272 ++++++++
>  4 files changed, 1573 insertions(+)
>  create mode 100644 drivers/spi/spi-cadence-quadspi.c
>  create mode 100644 drivers/spi/spi-cadence-quadspi.h
> 
> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
> index 6f7fdcbb9151..ef4d961feb54 100644
> --- a/drivers/spi/Kconfig
> +++ b/drivers/spi/Kconfig
> @@ -192,6 +192,16 @@ config SPI_CADENCE
>  	  This selects the Cadence SPI controller master driver
>  	  used by Xilinx Zynq and ZynqMP.
>  
> +config SPI_CADENCE_QUADSPI
> +	tristate "Cadence Quad SPI controller"
> +	depends on OF && (ARM || ARM64 || COMPILE_TEST || X86)
> +	depends on MTD || MTD_SPI_NOR || MTD_SPI_NAND
> +	help
> +	  Cadence QSPI is a specialized controller for connecting an SPI
> +	  Flash over 1/2/4-bit wide bus. This enables support for the Quad SPI

Supports Octal mode as well. So its 1/2/4/8-bit wide

> +	  controller in master mode. This driver does not support generic SPI.
> +	  The implementation only supports spi-mem interface.
> +
>  config SPI_CLPS711X
>  	tristate "CLPS711X host SPI controller"
>  	depends on ARCH_CLPS711X || COMPILE_TEST
> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
> index bb49c9e6d0a0..84a59d75a13a 100644
> --- a/drivers/spi/Makefile
> +++ b/drivers/spi/Makefile
> @@ -29,6 +29,7 @@ obj-$(CONFIG_SPI_BCM_QSPI)		+= spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.
>  obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
>  obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
>  obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
> +obj-$(CONFIG_SPI_CADENCE_QUADSPI)		+= spi-cadence-quadspi.o
>  obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
>  obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
>  obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
> diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
> new file mode 100644
> index 000000000000..bca391bfb58f
> --- /dev/null
> +++ b/drivers/spi/spi-cadence-quadspi.c
> @@ -0,0 +1,1290 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Driver for Cadence QSPI Controller
> + *
> + * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
> + * Copyright Intel Corporation (C) 2019. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program.  If not, see <http://www.gnu.org/licenses/>.
> + */
> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/delay.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/dmaengine.h>
> +#include <linux/errno.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/jiffies.h>
> +#include <linux/kernel.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
> +#include <linux/of.h>
> +#include <linux/of_platform.h>
> +#include <linux/of_address.h>
> +#include <linux/of_irq.h>
> +#include <linux/platform_device.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spi/spi-mem.h>
> +#include <linux/unaligned/be_byteshift.h>
> +
> +#include "spi-cadence-quadspi.h"
> +
> +/* Quirks */
> +#define CQSPI_NEEDS_WR_DELAY		BIT(0)
> +#define CQSPI_DISABLE_DAC_MODE		BIT(1)
> +
> +#define CADENCE_QSPI_NAME                       "cadence-qspi"
> +
> +struct cqspi_driver_platdata {
> +	u32 hwcaps_mask;
> +	u8 quirks;
> +};
> +
> +unsigned int cadence_qspi_init_timeout(const unsigned long timeout_in_ms)
> +{
> +	return jiffies + msecs_to_jiffies(timeout_in_ms);
> +}
> +
> +unsigned int cadence_qspi_check_timeout(const unsigned long timeout)
> +{
> +	return time_before(jiffies, timeout);
> +}
> +
> +static irqreturn_t cadence_qspi_irq_handler(int this_irq, void *dev)
> +{
> +	struct struct_cqspi *cadence_qspi = dev;
> +	u32 irq_status;
> +
> +	/* Read interrupt status */
> +	irq_status = readl(cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
> +	if (!irq_status)
> +		return IRQ_HANDLED;
> +
> +	cadence_qspi->irq_status = irq_status;
> +
> +	/* Clear interrupt */
> +	writel(irq_status, cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
> +	if (irq_status)
> +		complete(&cadence_qspi->transfer_complete);
> +
> +	return IRQ_HANDLED;
> +}
> +
> +static u32 cadence_qspi_cmd2addr(const unsigned char *addr_buf, u32 addr_width)
> +{
> +	unsigned int addr = 0;
> +	int i;
> +
> +	/* Invalid address return zero. */
> +	if (addr_width > 4)
> +		return 0;
> +
> +	for (i = 0; i < addr_width; i++) {
> +		addr = addr << 8;
> +		addr |= addr_buf[i];
> +	}
> +
> +	return addr;
> +}
> +
> +void enable_qspi_direct_access(void *reg_base, bool enable)
> +{

Please be consistent with function names. Start all functions with
cadence_qspi_. If need you could have a shorter function prefix like cqspi_

Also, this and few other functions below can be static and they are not
used outside of this module.

> +	u32 reg;
> +
> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
> +	if (enable)
> +		reg |= CQSPI_REG_CONFIG_DIRECT_MASK;
> +	else
> +		reg &= ~CQSPI_REG_CONFIG_DIRECT_MASK;
> +
> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
> +}
> +
> +void cadence_qspi_controller_enable(void *reg_base, bool enable)
> +{
> +	unsigned int reg;
> +
> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
> +	if (enable)
> +		reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
> +	else
> +		reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
> +
> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
> +}
> +
> +static unsigned int cadence_qspi_wait_idle(void *reg_base)
> +{
> +	u32 timeout, count = 0;
> +
> +	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
> +	while (cadence_qspi_check_timeout(timeout)) {
> +		if (CQSPI_REG_IS_IDLE(reg_base)) {
> +			count++;
> +			if (count >= CQSPI_POLL_IDLE_RETRY)
> +				return 1;
> +		} else {
> +			count = 0;
> +		}
> +	}
> +
> +	return 0;
> +}
> +

Could you please keep polling routines from original driver
(drivers/mtd/spi-nor/cadence-quadspi.c). If you really want to improve
these helpers, please do those changes in a separate patch later on in
the series. This will greatly help in reviewing the code.

Also, I see that you have dropped many inline comments in the code.
These comments are quite important and I suggest not to drop them unless
they are no longer applicable

> +static void cadence_qspi_readdata_capture(void *reg_base, u32 bypass, u32 delay)
> +{
> +	unsigned int reg;
> +
> +	cadence_qspi_controller_enable(reg_base, 0);
> +
> +	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
> +	if (bypass)
> +		reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
> +	else
> +		reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
> +
> +	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
> +		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
> +	reg |= ((delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
> +		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
> +	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
> +
> +	cadence_qspi_controller_enable(reg_base, 1);
> +}
> +
> +static void cadence_qspi_config_baudrate_div(void *reg_base, u32 ref_clk_hz,
> +					     u32 sclk_hz)
> +{
> +	unsigned int reg, div;
> +
> +	/* Recalculate the baudrate divisor based on QSPI specification. */
> +	div = DIV_ROUND_UP(ref_clk_hz, 2 * sclk_hz) - 1;
> +
> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
> +	reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);
> +	div = (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB;
> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
> +}
> +
> +static void cadence_qspi_cs(void *reg_base, u32 chip_select, u32 decoder_enable)
> +{
> +	unsigned int reg;
> +
> +	cadence_qspi_controller_enable(reg_base, 0);
> +
> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
> +	/* docoder */

s/docoder/decoder

> +	if (decoder_enable) {
> +		reg |= CQSPI_REG_CONFIG_DECODE_MASK;
> +	} else {
> +		reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
> +		chip_select = 0xF & ~(1 << chip_select);
> +	}
> +	reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
> +			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB);
> +	reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
> +			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB;
> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
> +	cadence_qspi_controller_enable(reg_base, 1);
> +}
> +
> +static int cadence_qspi_exec_flash_cmd(void *reg_base, unsigned int reg)
> +{
> +	unsigned int timeout;
> +
> +	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
> +	reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
> +	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
> +
> +	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
> +	while (cadence_qspi_check_timeout(timeout)) {
> +		reg = readl(reg_base + CQSPI_REG_CMDCTRL) &
> +			CQSPI_REG_CMDCTRL_INPROGRESS_MASK;
> +		if (!reg)
> +			break;
> +	}
> +

Please use cqspi_wait_for_bit() that uses readl_relaxed_poll_timeout()
here. There are couple corner cases that above code does not take care of.

> +	if (!cadence_qspi_wait_idle(reg_base) || reg != 0)
> +		return -EIO;
> +
> +	return 0;
> +}
> +
> +static int cqspi_command_read(void *reg_base, u32 txlen, const u_char *txbuf,
> +			      u32 addrlen, const u8 *addrbuf, u32 rxlen,
> +			      u8 *rxbuf, u32 flash_type)
> +{
> +	u32 addr_value, read_len, reg;
> +	int ret;
> +
> +	if (!rxlen || rxlen > CQSPI_STIG_DATA_LEN_MAX || !rxbuf)
> +		return -EINVAL;
> +
> +	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
> +	reg |= BIT(CQSPI_REG_CMDCTRL_RD_EN_LSB);
> +
> +	if (addrlen) {
> +		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
> +		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
> +			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
> +		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
> +	}
> +	/* 0 means 1 byte. */
> +	reg |= (((rxlen - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
> +		<< CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
> +	ret = cadence_qspi_exec_flash_cmd(reg_base, reg);
> +	if (ret != 0)
> +		return ret;
> +
> +	reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER);
> +	read_len = (rxlen > 4) ? 4 : rxlen;
> +	memcpy(rxbuf, &reg, read_len);
> +	rxbuf += read_len;
> +
> +	if (rxlen > 4) {
> +		reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER);
> +		read_len = rxlen - read_len;
> +		memcpy(rxbuf, &reg, read_len);
> +	}
> +
> +	return 0;
> +}
> +
> +static int cqspi_command_write(void *reg_base, u32 txlen, const u8 *txbuf,
> +			       u32 addrlen, const u8 *addrbuf, u32 datalen,
> +			       const u8 *databuf, u32 flash_type)
> +{
> +	unsigned int addr_value, reg, data = 0;
> +
> +	if (!txlen || !txbuf)
> +		return -EINVAL;
> +
> +	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
> +	if (datalen != 0) {
> +		reg |= BIT(CQSPI_REG_CMDCTRL_WR_EN_LSB);
> +		reg |= ((datalen - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
> +			<< CQSPI_REG_CMDCTRL_WR_BYTES_LSB;
> +		memcpy(&data, databuf, datalen);
> +		writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER);
> +	}
> +	if (addrlen) {
> +		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
> +		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
> +			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
> +		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
> +	}
> +
> +	return cadence_qspi_exec_flash_cmd(reg_base, reg);
> +}
> +
> +static int cqspi_indirect_read_setup(void *reg_base, u32 txlen, const u8 *txbuf,
> +				     u32 addrlen, const u8 *addrbuf,
> +				     u32 dummy_bytes, u32 flash_type,
> +				     u32 quad_mode)
> +{
> +	unsigned int addr_value, dummy_clk, reg;
> +
> +	if (addrlen) {
> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
> +		writel(addr_value, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
> +	}
> +
> +	reg = txbuf[0] << CQSPI_REG_RD_INSTR_OPCODE_LSB;
> +	reg |= (quad_mode & CQSPI_REG_RD_INSTR_TYPE_DATA_MASK) <<
> +		CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
> +
> +	if (dummy_bytes) {
> +		if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
> +			dummy_bytes = CQSPI_DUMMY_BYTES_MAX;
> +		reg |= BIT(CQSPI_REG_RD_INSTR_MODE_EN_LSB);
> +		writel(0xFF, reg_base + CQSPI_REG_MODE_BIT);
> +		dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
> +		dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;
> +		if (dummy_clk)
> +			reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
> +				<< CQSPI_REG_RD_INSTR_DUMMY_LSB;
> +	} else if (flash_type == QSPI_FLASH_TYPE_NAND) {
> +		reg |= ((1 * CQSPI_DUMMY_CLKS_PER_BYTE)
> +				<< CQSPI_REG_RD_INSTR_DUMMY_LSB);
> +	}

Why do we need flash type specific handling here? Does not spi-nand
driver provide appropriate dummy_clk values? Why is the driver always
adding 8 dummy clks always?

> +	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
> +	/* Set device size */
> +	reg = readl(reg_base + CQSPI_REG_SIZE);
> +	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
> +	reg |= (addrlen - 1);
> +	writel(reg, reg_base + CQSPI_REG_SIZE);
> +	/* disable auto-polling */
> +	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
> +	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
> +	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
> +
> +	return 0;
> +}
> +
> +static void cqspi_request_mmap_dma(struct struct_cqspi *cqspi)
> +{
> +	dma_cap_mask_t mask;
> +
> +	dma_cap_zero(mask);
> +	dma_cap_set(DMA_MEMCPY, mask);
> +
> +	cqspi->rx_chan = dma_request_chan_by_mask(&mask);
> +	if (IS_ERR(cqspi->rx_chan)) {
> +		dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
> +		cqspi->rx_chan = NULL;
> +	}
> +	init_completion(&cqspi->rx_dma_complete);
> +}
> +
> +static void cqspi_rx_dma_callback(void *param)
> +{
> +	struct struct_cqspi *cqspi = param;
> +
> +	complete(&cqspi->rx_dma_complete);
> +}
> +
> +static int cqspi_direct_read_execute(struct struct_cqspi *cqspi, u8 *buf,
> +				     const u8 *addrbuf, size_t rxlen)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct device *dev = &pdev->dev;
> +	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
> +	dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + addrbuf[0];
> +	void __iomem *ahb_base = cqspi->qspi_ahb_virt;
> +	int ret = 0;
> +	struct dma_async_tx_descriptor *tx;
> +	dma_cookie_t cookie;
> +	dma_addr_t dma_dst;
> +
> +	if (!cqspi->rx_chan || !virt_addr_valid(buf)) {
> +		memcpy_fromio(buf, ahb_base + addrbuf[0], rxlen);
> +		return 0;
> +	}
> +
> +	dma_dst = dma_map_single(dev, buf, rxlen, DMA_FROM_DEVICE);
> +	if (dma_mapping_error(dev, dma_dst)) {
> +		dev_err(dev, "dma mapping failed\n");
> +		return -ENOMEM;
> +	}
> +	tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src,
> +				       rxlen, flags);
> +	if (!tx) {
> +		dev_err(dev, "device_prep_dma_memcpy error\n");
> +		ret = -EIO;
> +		goto err_unmap;
> +	}
> +
> +	tx->callback = cqspi_rx_dma_callback;
> +	tx->callback_param = cqspi;
> +	cookie = tx->tx_submit(tx);
> +	reinit_completion(&cqspi->rx_dma_complete);
> +
> +	ret = dma_submit_error(cookie);
> +	if (ret) {
> +		dev_err(dev, "dma_submit_error %d\n", cookie);
> +		ret = -EIO;
> +		goto err_unmap;
> +	}
> +
> +	dma_async_issue_pending(cqspi->rx_chan);
> +	if (!wait_for_completion_timeout(&cqspi->rx_dma_complete,
> +					 msecs_to_jiffies(rxlen))) {
> +		dmaengine_terminate_sync(cqspi->rx_chan);
> +		dev_err(dev, "DMA wait_for_completion_timeout\n");
> +		ret = -ETIMEDOUT;
> +		goto err_unmap;
> +	}
> +
> +err_unmap:
> +	dma_unmap_single(dev, dma_dst, rxlen, DMA_FROM_DEVICE);
> +
> +	return ret;
> +}
> +
> +static int cqspi_indirect_read_execute(struct struct_cqspi *cqspi, u32 rxlen,
> +				       u8 *rxbuf, u32 flash_type)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	void *reg_base = cqspi->iobase;
> +	void *ahb_base = cqspi->qspi_ahb_virt;
> +	u8 *rxbuf_end = rxbuf + rxlen;
> +	u32 mod_bytes = rxlen % 4;
> +	u32 bytes_to_read = 0;
> +	int remaining = (int)rxlen;
> +	u32 timeout, reg = 0;
> +	int ret = 0;
> +
> +	writel(0, reg_base + CQSPI_REG_INDIRECTRDWATERMARK);
> +	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
> +	writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
> +
> +	mb();/* flush previous writes */
> +
> +	writel(pdata->fifo_depth - CQSPI_REG_SRAM_RESV_WORDS,
> +	       reg_base + CQSPI_REG_SRAMPARTITION);
> +	/* Clear all interrupts. */
> +	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
> +	writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
> +
> +	reinit_completion(&cqspi->transfer_complete);
> +	writel(CQSPI_REG_INDIRECTRD_START_MASK,
> +	       reg_base + CQSPI_REG_INDIRECTRD);
> +
> +	while (remaining > 0) {
> +		bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
> +
> +		while (bytes_to_read != 0) {
> +			unsigned int word_remain = round_down(remaining, 4);
> +
> +			bytes_to_read *= CQSPI_FIFO_WIDTH;
> +			bytes_to_read = bytes_to_read > remaining ?
> +						remaining : bytes_to_read;
> +			bytes_to_read = round_down(bytes_to_read, 4);
> +			if (bytes_to_read) {
> +				ioread32_rep(ahb_base, rxbuf,
> +					     (bytes_to_read / 4));
> +			} else if (!word_remain && mod_bytes) {
> +				unsigned int temp = ioread32(ahb_base);
> +
> +				bytes_to_read = mod_bytes;
> +				memcpy(rxbuf, &temp, min((unsigned int)
> +				       (rxbuf_end - rxbuf), bytes_to_read));
> +			}
> +
> +			rxbuf += bytes_to_read;
> +			remaining -= bytes_to_read;
> +			bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
> +		}
> +
> +		if (remaining < 0)
> +			reinit_completion(&cqspi->transfer_complete);
> +	}
> +
> +	/* Check indirect done status */
> +	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
> +	while (cadence_qspi_check_timeout(timeout)) {
> +		reg = readl(reg_base + CQSPI_REG_INDIRECTRD);
> +		if (reg & CQSPI_REG_INDIRECTRD_DONE_MASK)
> +			break;
> +	}
> +	if (!(reg & CQSPI_REG_INDIRECTRD_DONE_MASK)) {
> +		dev_err(&pdev->dev, "QSPI : Indirect read error %x\n", reg);
> +		ret = -ETIMEDOUT;
> +		goto failrd;
> +	}
> +	/* Disable interrupt */
> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
> +	/* Clear indirect completion status */
> +	writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD);
> +
> +	return 0;
> +failrd:
> +	/* Disable interrupt */
> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
> +	/* Cancel the indirect read */
> +	writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
> +	       reg_base + CQSPI_REG_INDIRECTRD);
> +	return ret;
> +}
> +
> +static int cqspi_indirect_write_setup(void *reg_base, u32 txlen,
> +				      const u8 *txbuf, u32 addrlen,
> +				      const u8 *addrbuf, u32 flash_type,
> +				      u32 quad_mode)
> +{
> +	unsigned int reg;
> +
> +	if (!txbuf)
> +		return -EINVAL;
> +
> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
> +	reg &= ~(CQSPI_REG_CONFIG_DIRECT_MASK);
> +	reg &= ~(CQSPI_REG_CONFIG_DMA_MASK);
> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
> +
> +	/* Set opcode. */
> +	reg = txbuf[0] << CQSPI_REG_WR_INSTR_OPCODE_LSB;
> +	reg |= BIT(CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS);
> +	if (txbuf[0] == MACRONIX_4PP_CMD && flash_type == QSPI_FLASH_TYPE_NOR &&
> +	    quad_mode == QUAD_QIO) {
> +		/* Configure the quad */
> +		reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK) <<
> +		       CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
> +	}

Nope, no custom handling or interpreting of opcodes in driver.
Just set addrwidth to quad in CQSPI_REG_WR_INSTR when op->addr.buswidth
is 4.


> +	/* Configure the quad */
> +	reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_DATA_MASK) <<
> +	       CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
> +	writel(reg, reg_base + CQSPI_REG_WR_INSTR);
> +	/* Setup write address. */
> +	reg = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
> +	writel(reg, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR);
> +	reg = readl(reg_base + CQSPI_REG_SIZE);
> +	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
> +	reg |= ((addrlen - 1) & CQSPI_REG_SIZE_ADDRESS_MASK);
> +	writel(reg, reg_base +  CQSPI_REG_SIZE);
> +
> +	/* disable auto-polling */
> +	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
> +	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
> +	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
> +
> +	return 0;
> +}
> +
> +static int cqspi_indirect_write_execute(struct struct_cqspi *cqspi, u32 txlen,
> +					const u8 *txbuf, u32 flash_type)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	struct cqspi_flash_pdata *f_pdata =
> +			&pdata->f_pdata[cqspi->current_cs];
> +	void *reg_base = cqspi->iobase;
> +	void *ahb_base = cqspi->qspi_ahb_virt;
> +	u32 *irq_status = &cqspi->irq_status;
> +	u32 page_size = f_pdata->page_size;
> +	u32 write_bytes, timeout, reg = 0;
> +	int remaining = (int)txlen;
> +	int ret;
> +
> +	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
> +	writel(0x0, reg_base + CQSPI_REG_INDIRECTWRWATERMARK);
> +	reg = readl(reg_base + CQSPI_REG_SIZE);
> +	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
> +	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
> +	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
> +	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
> +	writel(reg, reg_base +  CQSPI_REG_SIZE);
> +
> +	writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
> +	writel(CQSPI_REG_SRAM_PARTITION_WR, reg_base + CQSPI_REG_SRAMPARTITION);
> +	/* Clear all interrupts. */
> +	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
> +	writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK);
> +	reinit_completion(&cqspi->transfer_complete);
> +	writel(CQSPI_REG_INDIRECTWR_START_MASK,
> +	       reg_base + CQSPI_REG_INDIRECTWR);
> +
> +	if (cqspi->wr_delay)
> +		ndelay(cqspi->wr_delay);
> +
> +	while (remaining > 0) {
> +		size_t write_words, mod_bytes;
> +
> +		write_bytes = remaining > page_size ? page_size : remaining;
> +		write_words = write_bytes / 4;
> +		mod_bytes = write_bytes % 4;
> +
> +		if (write_words) {
> +			iowrite32_rep(ahb_base, txbuf, write_words);
> +			txbuf += (write_words * 4);
> +		}
> +		if (mod_bytes) {
> +			unsigned int temp = 0xFFFFFFFF;
> +
> +			memcpy(&temp, txbuf, mod_bytes);
> +			iowrite32(temp, ahb_base);
> +			txbuf += mod_bytes;
> +		}
> +		ret = wait_event_interruptible_timeout(cqspi->waitqueue,
> +						       *irq_status &
> +						       CQSPI_IRQ_MASK_WR,
> +						       CQSPI_TIMEOUT_MS);

This was wait_for_completion_timeout() previously. Have you tested
interrupting the sleep and verified that driver handles this case correctly?

> +		if (!(ret) & (*irq_status & CQSPI_IRQ_STATUS_ERR)) {
> +			ret = -ETIMEDOUT;
> +			goto failwr;
> +		} else {
> +			ret = 0;
> +		}
> +		remaining -= write_bytes;
> +
> +		if (remaining < 0)
> +			reinit_completion(&cqspi->transfer_complete);
> +	}
> +
> +	/* Check indirect done status */
> +	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
> +	while (cadence_qspi_check_timeout(timeout)) {
> +		reg = readl(reg_base + CQSPI_REG_INDIRECTWR);
> +		if (reg & CQSPI_REG_INDIRECTWR_DONE_MASK)
> +			break;
> +	}
> +	if (!(reg & CQSPI_REG_INDIRECTWR_DONE_MASK)) {
> +		dev_err(&pdev->dev, "QSPI: Indirect write error %x", reg);
> +		ret = -ETIMEDOUT;
> +		goto failwr;
> +	}
> +
> +	return 0;
> +
> +failwr:
> +	/* Disable interrupt. */
> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
> +	/* Clear indirect completion status */
> +	writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR);
> +
> +	/* Cancel the indirect write */
> +	if (ret)
> +		writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
> +		       reg_base + CQSPI_REG_INDIRECTWR);
> +
> +	return ret;
> +}
> +
> +unsigned int cadence_qspi_is_controller_ready(void *reg_base)
> +{
> +	return cadence_qspi_wait_idle(reg_base);
> +}
> +
> +void cadence_qspi_controller_init(struct struct_cqspi *cqspi)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +
> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
> +
> +	/* Configure the remap address register, no remap */
> +	writel(0, cqspi->iobase + CQSPI_REG_REMAP);
> +	/* Disable all interrupts. */
> +	writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
> +
> +	/* DAC is disabled for Intel LGM SOC */
> +	if (!cqspi->dac_mode) {
> +		enable_qspi_direct_access(cqspi->iobase, 0);
> +	} else {
> +		enable_qspi_direct_access(cqspi->iobase, 1);
> +		/* TODO: for TI platform to be enabled */
> +		cqspi_request_mmap_dma(cqspi);
> +	}
> +
> +	/* Load indirect trigger address. */
> +	writel(pdata->trigger_address,
> +	       cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER);
> +
> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
> +}
> +
> +unsigned int calculate_ticks_for_ns(u32 ref_clk_hz, u32 ns_val)
> +{
> +	unsigned int ticks;
> +
> +	ticks = ref_clk_hz / 1000;      /* kHz */
> +	ticks = DIV_ROUND_UP(ticks * ns_val, 1000000);
> +
> +	return ticks;
> +}
> +
> +void cadence_qspi_delay(struct struct_cqspi *cqspi, u32 ref_clk, u32 sclk_hz)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cqspi->current_cs];
> +	void __iomem *iobase = cqspi->iobase;
> +	const unsigned int ref_clk_hz = pdata->master_ref_clk_hz;
> +	unsigned int tshsl, tchsh, tslch, tsd2d;
> +	unsigned int reg;
> +	unsigned int tsclk;
> +
> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
> +	/* calculate the number of ref ticks for one sclk tick */
> +	tsclk = DIV_ROUND_UP(ref_clk_hz, sclk_hz);
> +
> +	/* this particular value must be at least one sclk */
> +	if (tshsl < tsclk)
> +		tshsl = tsclk;
> +
> +	tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns);
> +	tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns);
> +	tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns);
> +
> +	reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
> +			<< CQSPI_REG_DELAY_TSHSL_LSB);
> +	reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
> +			<< CQSPI_REG_DELAY_TCHSH_LSB);
> +	reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
> +			<< CQSPI_REG_DELAY_TSLCH_LSB);
> +	reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
> +			<< CQSPI_REG_DELAY_TSD2D_LSB);
> +	writel(reg, iobase + CQSPI_REG_DELAY);
> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
> +}
> +
> +void cadence_qspi_switch_chipselect(struct struct_cqspi *cqspi, u32 cs)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cs];
> +	void __iomem *iobase = cqspi->iobase;
> +	unsigned int reg;
> +
> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
> +	/* Configure page size and block size. */
> +	reg = readl(iobase + CQSPI_REG_SIZE);
> +	/* clear the previous value */
> +	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
> +	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
> +	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
> +	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
> +	writel(reg, iobase + CQSPI_REG_SIZE);
> +	/* configure the chip select */
> +	cadence_qspi_cs(iobase, cs, pdata->ext_decoder);
> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
> +}
> +
> +static int cadence_qspi_mem_process(struct struct_cqspi *cqspi,
> +				    struct spi_mem *mem,
> +				    const struct spi_mem_op *op)
> +{
> +	struct platform_device *pdev = cqspi->pdev;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	unsigned int tmpbufsize, n_trans = 0, totalxferlen = 0;
> +	void __iomem *iobase = cqspi->iobase;
> +	struct spi_mem_op_cadence ops[4] = { };
> +	struct spi_mem_op_cadence *cmd_ops = NULL;
> +	struct spi_mem_op_cadence *data_ops = NULL;
> +	struct spi_mem_op_cadence *dummy_ops = NULL;
> +	struct spi_mem_op_cadence *addr_ops = NULL;
> +	struct cqspi_flash_pdata *f_pdata;
> +	int rdid_length, mode, ret, i;
> +	u8 *tmpbuf;
> +	u32 sclk;
> +
> +	if (cqspi->current_cs != mem->spi->chip_select) {
> +		cqspi->current_cs = mem->spi->chip_select;
> +		cadence_qspi_switch_chipselect(cqspi, mem->spi->chip_select);
> +	}
> +
> +	f_pdata = &pdata->f_pdata[cqspi->current_cs];
> +	if (f_pdata->flash_type == QSPI_FLASH_TYPE_NOR)
> +		rdid_length = 6;
> +	else
> +		rdid_length = 3;
> +

What? NACK... why should driver worry about rdid_length?


> +	tmpbufsize = sizeof(op->cmd.opcode) + op->addr.nbytes +
> +			op->dummy.nbytes;
> +
> +	tmpbuf = kzalloc(tmpbufsize, GFP_KERNEL | GFP_DMA);
> +	if (!tmpbuf)
> +		return -ENOMEM;
> +
> +	tmpbuf[0] = op->cmd.opcode;
> +	ops[n_trans].tx_buf = tmpbuf;
> +	ops[n_trans].len = sizeof(op->cmd.opcode);
> +	ops[n_trans].tx_nbits = op->cmd.buswidth;
> +
> +	n_trans++;
> +	totalxferlen++;
> +
> +	if (op->addr.nbytes) {
> +		int i;
> +
> +		for (i = 0; i < op->addr.nbytes; i++)
> +			tmpbuf[i + 1] = op->addr.val >>
> +					(8 * (op->addr.nbytes - i - 1));
> +
> +		ops[n_trans].tx_buf = tmpbuf + 1;
> +		ops[n_trans].len = op->addr.nbytes;
> +		ops[n_trans].tx_nbits = op->addr.buswidth;
> +
> +		n_trans++;
> +		totalxferlen += op->addr.nbytes;
> +	}
> +	if (op->dummy.nbytes) {
> +		memset(tmpbuf + op->addr.nbytes + 1, 0xff, op->dummy.nbytes);
> +		ops[n_trans].tx_buf = tmpbuf + op->addr.nbytes + 1;
> +		ops[n_trans].len = op->dummy.nbytes;
> +		ops[n_trans].tx_nbits = op->dummy.buswidth;
> +
> +		n_trans++;
> +		totalxferlen += op->dummy.nbytes;
> +	}
> +	if (op->data.nbytes) {
> +		if (op->data.dir == SPI_MEM_DATA_IN) {
> +			ops[n_trans].rx_buf = op->data.buf.in;
> +			ops[n_trans].rx_nbits = op->data.buswidth;
> +		} else {
> +			ops[n_trans].tx_buf = op->data.buf.out;
> +			ops[n_trans].tx_nbits = op->data.buswidth;
> +		}
> +
> +		ops[n_trans].len = op->data.nbytes;
> +		n_trans++;
> +		totalxferlen += op->data.nbytes;
> +	}
> +
> +	for (i = 0; i < n_trans; i++)
> +		dev_dbg(&pdev->dev, "ops[%d] %d\n", i, ops[i].len);
> +
> +	switch (n_trans) {
> +	case 1:
> +		cmd_ops = &ops[0];
> +		break;
> +	case 2:
> +		cmd_ops = &ops[0];
> +		if (f_pdata->flash_type == QSPI_FLASH_TYPE_NAND) {
> +			if (data_ops->rx_buf)
> +				data_ops = &ops[1];
> +			else
> +				addr_ops = &ops[1];
> +		} else {
> +			data_ops = &ops[1];
> +		}


Please get ride of all flash type specific handling... There should be
no need for it. IF there are gaps in then lets discuss and fix it in
spi-nand and spi-nor frameworks and not in the driver.

spi-mem user should just take spi_mem_op template passed by the core and
execute it. No assumptions wrt flash type or opcode should be done.

> +		break;
> +	case 3:
> +		cmd_ops = &ops[0];
> +		addr_ops = &ops[1];
> +		data_ops = &ops[2];
> +		break;
> +	case 4:
> +		cmd_ops = &ops[0];
> +		addr_ops = &ops[1];
> +		dummy_ops = &ops[2];
> +		data_ops = &ops[3];
> +		break;
> +	default:
> +		dev_err(&pdev->dev, "Unsupported n_trans %u\n", n_trans);
> +		return -EINVAL;
> +	}
> +
> +	if (!data_ops)
> +		mode = STIG_WRITE_MODE;
> +	else if (data_ops->len > rdid_length)
> +		mode = data_ops->tx_buf ? IDC_WRITE_MODE : IDC_READ_MODE;
> +	else
> +		mode = data_ops->tx_buf ? STIG_WRITE_MODE : STIG_READ_MODE;
> +

Decision to use STIG was INDAC mode can be done using:

        if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) {
                if (!op->addr.nbytes)
                        mode = CQSPI_STIG_READ;
                else
                        mode = IDC_READ_MODE;
        } else {
                if (!op->addr.nbytes || !op->data.buf.out)
                        mode = CQSPI_STIG_WRITE;
                else
                        mode = IDC_WRITE_MODE;
        }

No need for rdid_length etc.

> +	sclk = mem->spi->max_speed_hz;
> +	cadence_qspi_controller_enable(iobase, 0);
> +	cadence_qspi_config_baudrate_div(iobase, pdata->master_ref_clk_hz,
> +					 sclk);
> +	cadence_qspi_delay(cqspi, pdata->master_ref_clk_hz, sclk);
> +	cadence_qspi_readdata_capture(iobase, 1, f_pdata->read_delay);
> +	cadence_qspi_controller_enable(iobase, 1);
> +
> +	/* execute transfer */
> +	switch (mode) {
> +	case STIG_WRITE_MODE:
> +		ret = cqspi_command_write(iobase, cmd_ops->len, cmd_ops->tx_buf,
> +					  addr_ops ? addr_ops->len : 0,
> +					  addr_ops ? addr_ops->tx_buf : NULL,
> +					  data_ops ? data_ops->len : 0,
> +					  data_ops ? data_ops->tx_buf : NULL,
> +					  f_pdata->flash_type);
> +		break;
> +	case STIG_READ_MODE:
> +		ret = cqspi_command_read(iobase, cmd_ops->len, cmd_ops->tx_buf,
> +					 addr_ops ? addr_ops->len : 0,
> +					 addr_ops ? addr_ops->tx_buf : NULL,
> +					 data_ops ? data_ops->len : 0,
> +					 data_ops ? data_ops->rx_buf : NULL,
> +					 f_pdata->flash_type);
> +		break;
> +	case IDC_WRITE_MODE:
> +		ret = cqspi_indirect_write_setup(iobase, cmd_ops->len,
> +						 cmd_ops->tx_buf,
> +						 addr_ops ? addr_ops->len : 0,
> +						 addr_ops ? addr_ops->tx_buf : 0,
> +						 f_pdata->flash_type,
> +						 f_pdata->quad);
> +		ret = cqspi_indirect_write_execute(cqspi, data_ops->len,
> +						   data_ops->tx_buf,
> +						   f_pdata->flash_type);
> +		break;
> +	case IDC_READ_MODE:
> +		ret = cqspi_indirect_read_setup(iobase, cmd_ops->len,
> +						cmd_ops->tx_buf,
> +						addr_ops ? addr_ops->len : 0,
> +						addr_ops ? addr_ops->tx_buf : 0,
> +						dummy_ops ? dummy_ops->len : 0,
> +						f_pdata->flash_type,
> +						f_pdata->quad);
> +		ret = cqspi_indirect_read_execute(cqspi, data_ops->len,
> +						  data_ops->rx_buf,
> +						  f_pdata->flash_type);
> +		/* TODO: for TI DMA + DAC to be enabled */

This is a big gap and there is lot of code sharing that can be done b/w
INDAC and DAC mode.

Looks like driver isn't quite close to being ready. I suggest you also
take a look at patches for spi-mem conversion of cadence-quadspi driver
in U-Boot as well:

https://patchwork.ozlabs.org/cover/1176362/

> +		break;
> +	default:
> +		dev_err(&pdev->dev, "Unsupported mode %u\n", mode);
> +		return -EINVAL;
> +	}
> +
> +	return ret;
> +}
> +
> +int cadence_qspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
> +{
> +	struct struct_cqspi *cqspi = spi_master_get_devdata(mem->spi->master);
> +	int ret;
> +
> +	mutex_lock(&cqspi->lock);
> +	ret = cadence_qspi_mem_process(cqspi, mem, op);
> +	if (ret)
> +		dev_err(&mem->spi->dev, "Error: qspi transfer failed!!!.\n");
> +	mutex_unlock(&cqspi->lock);
> +
> +	return ret;
> +}
> +
> +static const struct spi_controller_mem_ops cadence_qspi_mem_ops = {
> +	.exec_op = cadence_qspi_exec_mem_op,
> +};
> +
> +static int cadence_qspi_setup(struct spi_device *spi)
> +{
> +	if (spi->chip_select > spi->master->num_chipselect) {
> +		dev_err(&spi->dev, "%d CS is out of range\n", spi->chip_select);
> +		return -EINVAL;
> +	}
> +	return 0;
> +}
> +
> +static int cadence_qspi_of_get_pdata(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct device_node *nc;
> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
> +	struct cqspi_flash_pdata *f_pdata;
> +	unsigned int cs;
> +	unsigned int prop;
> +
> +	pdata->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
> +
> +	if (of_property_read_u32(np, "cdns,trigger-address", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine trigger-address\n");
> +		return -ENXIO;
> +	}
> +	pdata->trigger_address = prop;
> +
> +	pdata->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
> +
> +	if (of_property_read_u32(np, "cdns,qspi-phyaddr", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine cdns,qspi-phyaddr\n");
> +		return -ENXIO;
> +	}
> +	pdata->qspi_ahb_phy = prop;
> +

Please dont add any new DT properties, there is no need for them. See
how this was handled in existing driver and reuse it

> +	if (of_property_read_u32(np, "cdns,qspi-physize", &prop)) {
> +		dev_info(&pdev->dev, "missing cdns,qspi-physize to 128 kB\n");
> +		prop = 128;
> +	}
> +	pdata->qspi_ahb_size = prop * 1024;
> +
> +	if (of_property_read_u32(np, "cdns,qspi-phymask", &prop))
> +		prop = CQSPI_INDIRECTTRIGGER_ADDR_MASK;
> +	pdata->qspi_ahb_mask = prop;
> +
> +	if (of_property_read_u32(np, "bus-num", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine bus-num\n");
> +		return -ENXIO;
> +	}
> +	pdata->bus_num = prop;
> +
> +	if (of_property_read_u32(np, "num-chipselect", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine num-chipselect\n");
> +		return -ENXIO;
> +	}
> +	pdata->num_chipselect = prop;
> +
> +	if (of_property_read_u32(np, "cdns,fifo-depth", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine fifo-depth\n");
> +		return -ENXIO;
> +	}
> +	pdata->fifo_depth = prop;
> +
> +	if (of_property_read_u32(np, "ext-decoder", &prop)) {
> +		dev_err(&pdev->dev, "couldn't determine ext-decoder\n");
> +		return -ENXIO;
> +	}
> +	pdata->ext_decoder = prop;
> +



> +	pdata->enable_dma = of_property_read_bool(np, "dmas");
> +	dev_info(&pdev->dev, "DMA %senabled\n", pdata->enable_dma ? "" : "NOT");
> +

Slave DMA was never supported and is not needed.

> +	/* Get flash devices platform data */
> +	for_each_child_of_node(np, nc) {
> +		if (!of_device_is_available(nc))
> +			continue;
> +
> +		if (of_property_read_u32(nc, "reg", &cs)) {
> +			dev_err(&pdev->dev, "couldn't determine reg\n");
> +			return -ENXIO;
> +		}
> +		f_pdata = &pdata->f_pdata[cs];
> +
> +		/* use compatible string to determine flash type */
> +		if (of_device_is_compatible(nc, "spinand"))
> +			f_pdata->flash_type = QSPI_FLASH_TYPE_NAND;
> +		else
> +			f_pdata->flash_type = QSPI_FLASH_TYPE_NOR;
> +
> +		if (of_property_read_u32(nc, "spi-rx-bus-width", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine quad\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->quad = (prop == 4) ? QUAD_QIO : QUAD_SIO;
> +
> +		if (of_property_read_u32(nc, "page-size", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine page-size\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->page_size = prop;
> +
> +		if (of_property_read_u32(nc, "block-size", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine block-size\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->block_size = prop;
> +
> +		if (of_property_read_u32(nc, "cdns,read-delay", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine read-delay\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->read_delay = prop;
> +
> +		if (of_property_read_u32(nc, "cdns,tshsl-ns", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine tshsl-ns\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->tshsl_ns = prop;
> +
> +		if (of_property_read_u32(nc, "cdns,tsd2d-ns", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->tsd2d_ns = prop;
> +
> +		if (of_property_read_u32(nc, "cdns,tchsh-ns", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine tchsh-ns\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->tchsh_ns = prop;
> +
> +		if (of_property_read_u32(nc, "cdns,tslch-ns", &prop)) {
> +			dev_err(&pdev->dev, "couldn't determine tslch-ns\n");
> +			return -ENXIO;
> +		}
> +		f_pdata->tslch_ns = prop;
> +	}
> +	return 0;
> +}
> +
> +static int cadence_qspi_probe(struct platform_device *pdev)
> +{
> +	struct cqspi_platform_data *pdata;
> +	struct device *dev = &pdev->dev;
> +	struct struct_cqspi *cqspi;
> +	struct spi_master *master;
> +	struct reset_control *rstc, *rstc_ocp;
> +	const struct cqspi_driver_platdata *ddata;
> +	struct resource *res = NULL;
> +	int ret;
> +
> +	master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
> +	if (!master) {
> +		dev_err(&pdev->dev, "spi_alloc_master failed\n");
> +		return -ENOMEM;
> +	}
> +	master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA | SPI_TX_QUAD |
> +				SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL;

Octal?

> +	master->setup = cadence_qspi_setup;
> +	master->mem_ops = &cadence_qspi_mem_ops;
> +	master->dev.of_node = pdev->dev.of_node;
> +	cqspi = spi_master_get_devdata(master);
> +	cqspi->pdev = pdev;
> +
> +	pdata = kmalloc(sizeof(*pdata), GFP_KERNEL);
> +	if (!pdata) {
> +		ret = -ENOMEM;
> +		goto err_pdata;
> +	}
> +	pdev->dev.platform_data = pdata;
> +
> +	cqspi->clk = devm_clk_get(&pdev->dev, "qspi");
> +	if (IS_ERR(cqspi->clk)) {
> +		dev_err(&pdev->dev, "cannot get qspi clk\n");
> +		return PTR_ERR(cqspi->clk);
> +	}
> +	pdata->master_ref_clk_hz = clk_get_rate(cqspi->clk);
> +
> +	ret = clk_prepare_enable(cqspi->clk);
> +	if (ret < 0) {
> +		dev_err(&pdev->dev, "failed to enable qspi clock: %d\n", ret);
> +		return ret;
> +	}
> +
> +	ret = cadence_qspi_of_get_pdata(pdev);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Get platform data failed.\n");
> +		return -ENODEV;
> +	}
> +
> +	cqspi->res = res;
> +	/* Obtain and remap controller address. */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> +	cqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
> +	if (IS_ERR(cqspi->iobase)) {
> +		dev_err(dev, "Cannot remap controller address.\n");
> +		return PTR_ERR(cqspi->iobase);
> +	}
> +
> +	/* Obtain and remap AHB address. */
> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> +	cqspi->qspi_ahb_virt = devm_ioremap_resource(dev, res);
> +	if (IS_ERR(cqspi->qspi_ahb_virt)) {
> +		dev_err(dev, "Cannot remap AHB address.\n");
> +		return PTR_ERR(cqspi->qspi_ahb_virt);
> +	}
> +	cqspi->mmap_phys_base = (dma_addr_t)res->start;
> +	cqspi->ahb_size = resource_size(res);
> +
> +	/* Obtain QSPI reset control */
> +	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
> +	if (IS_ERR(rstc)) {
> +		dev_err(dev, "Cannot get QSPI reset.\n");
> +		return PTR_ERR(rstc);
> +	}
> +
> +	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
> +	if (IS_ERR(rstc_ocp)) {
> +		dev_err(dev, "Cannot get QSPI OCP reset.\n");
> +		return PTR_ERR(rstc_ocp);
> +	}
> +
> +	reset_control_assert(rstc);
> +	reset_control_deassert(rstc);
> +
> +	reset_control_assert(rstc_ocp);
> +	reset_control_deassert(rstc_ocp);
> +
> +	ddata  = of_device_get_match_data(dev);
> +	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
> +		cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
> +						   pdata->master_ref_clk_hz);
> +
> +	init_completion(&cqspi->transfer_complete);
> +
> +	cqspi->irq = platform_get_irq(pdev, 0);
> +	if (cqspi->irq < 0) {
> +		dev_err(dev, "platform_get_irq failed.\n");
> +		ret = -ENXIO;
> +		goto err_irq;
> +	}
> +	ret = devm_request_irq(dev, cqspi->irq, cadence_qspi_irq_handler, 0,
> +			       pdev->name, cqspi);
> +	if (ret) {
> +		dev_err(dev, "request_irq failed.\n");
> +		goto err_irq;
> +	}
> +
> +	master->bus_num = pdata->bus_num;
> +	master->num_chipselect = pdata->num_chipselect;
> +	mutex_init(&cqspi->lock);
> +	platform_set_drvdata(pdev, master);
> +	cadence_qspi_controller_init(cqspi);
> +	cqspi->current_cs = 0;
> +
> +	ret = devm_spi_register_master(dev, master);
> +	if (ret) {
> +		dev_err(&pdev->dev, "devm_spi_register_master failed.\n");
> +		goto err_of;
> +	}
> +
> +	if (ddata && (ddata->quirks & CQSPI_DISABLE_DAC_MODE))
> +		cqspi->dac_mode = false;
> +
> +	return 0;
> +
> +err_pdata:
> +	kfree(pdata);
> +err_irq:
> +	free_irq(cqspi->irq, cqspi);
> +err_of:
> +	spi_master_put(master);
> +	dev_err(&pdev->dev, "Cadence QSPI controller probe failed\n");
> +	return ret;
> +}
> +
> +static int cadence_qspi_remove(struct platform_device *pdev)
> +{
> +	struct spi_master *master = platform_get_drvdata(pdev);
> +	struct struct_cqspi *cadence_qspi = spi_master_get_devdata(master);
> +
> +	cadence_qspi_controller_enable(cadence_qspi->iobase, 0);
> +	platform_set_drvdata(pdev, NULL);
> +	free_irq(cadence_qspi->irq, cadence_qspi);
> +	iounmap(cadence_qspi->iobase);
> +	iounmap(cadence_qspi->qspi_ahb_virt);
> +	release_mem_region(cadence_qspi->res->start,
> +			   resource_size(cadence_qspi->res));
> +	kfree(pdev->dev.platform_data);
> +	spi_unregister_master(master);
> +	spi_master_put(master);
> +	return 0;
> +}
> +
> +static const struct cqspi_driver_platdata k2g_qspi = {
> +	.quirks = CQSPI_NEEDS_WR_DELAY,
> +};
> +
> +static const struct cqspi_driver_platdata am654_ospi = {
> +	.quirks = CQSPI_NEEDS_WR_DELAY,
> +};
> +
> +static const struct cqspi_driver_platdata intel_lgm_qspi = {
> +	.quirks = CQSPI_DISABLE_DAC_MODE,
> +};
> +
> +#ifdef CONFIG_OF
> +static const struct of_device_id cadence_qspi_of_match[] = {
> +	{
> +		.compatible = "cadence,qspi",
> +	},
> +	{
> +		.compatible = "ti,k2g-qspi",
> +		.data = &k2g_qspi,
> +	},
> +	{
> +		.compatible = "ti,am654-ospi",
> +		.data = &am654_ospi,
> +	},
> +	{
> +		.compatible = "intel,lgm-qspi",
> +		.data = &intel_lgm_qspi,
> +	},
> +	{ /* end of table */}
> +};
> +MODULE_DEVICE_TABLE(of, cadence_qspi_of_match);
> +#else
> +#define cadence_qspi_of_match NULL
> +#endif /* CONFIG_OF */
> +
> +static struct platform_driver cadence_qspi_platform_driver = {
> +	.probe          = cadence_qspi_probe,
> +	.remove         = cadence_qspi_remove,
> +	.driver = {
> +		.name   = CADENCE_QSPI_NAME,
> +		.of_match_table = cadence_qspi_of_match,
> +	},
> +};
> +
> +module_platform_driver(cadence_qspi_platform_driver);
> +
> +MODULE_DESCRIPTION("Cadence QSPI Controller Driver");
> +MODULE_LICENSE("GPL v2");
> +MODULE_ALIAS("platform:" CADENCE_QSPI_NAME);
> +MODULE_AUTHOR("Ley Foon Tan <[e-mail]>");
> +MODULE_AUTHOR("Graham Moore <[e-mail]>");
> +MODULE_AUTHOR("Vadivel Murugan R <[e-mail]>");
> diff --git a/drivers/spi/spi-cadence-quadspi.h b/drivers/spi/spi-cadence-quadspi.h
> new file mode 100644
> index 000000000000..c78ee9423950
> --- /dev/null
> +++ b/drivers/spi/spi-cadence-quadspi.h
> @@ -0,0 +1,272 @@
> +/* SPDX-License-Identifier: BSD-2-Clause */

NACK, should be GPLv2 and no need for boilerplate text below when SPDX
Identifier is present.

> +/*
> + * Driver for Cadence QSPI Controller
> + *
> + * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
> + * Copyright Intel Corporation (C) 2019. All rights reserved.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> + *
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
> + * more details.
> + *
> + * You should have received a copy of the GNU General Public License along with
> + * this program.  If not, see <http://www.gnu.org/licenses/>.
> + */
> +#ifndef __CADENCE_QSPI__H__
> +#define __CADENCE_QSPI__H__
> +#include <linux/reset.h>
> +#include <linux/spi/spi-mem.h>
> +
> +#define CQSPI_MAX_CHIP_SELECT		(16)
> +#define STIG_READ_MODE			1
> +#define STIG_WRITE_MODE			2
> +#define STIG_WRITE_READ_MODE		3
> +#define IDC_READ_MODE			4
> +#define IDC_WRITE_MODE			5
> +
> +#define QSPI_FLASH_TYPE_NOR		0
> +#define QSPI_FLASH_TYPE_NAND		1
> +


> +#define QUAD_SIO			0
> +#define QUAD_DIO			1
> +#define QUAD_QIO			2
> +
> +#define QUAD_LSB			4
> +

Have driver specific prefixes please.

> +#define MACRONIX_4PP_CMD		0x38
> +#define MACRONIX_WRSR_CMD		0x01
> +

These needs to be dropped

> +/* Operation timeout value */
> +#define CQSPI_TIMEOUT_MS			5000
> +#define CQSPI_READ_TIMEOUT_MS			10
> +#define CQSPI_POLL_IDLE_RETRY			3
> +#define CQSPI_FIFO_WIDTH			4
> +
> +/* Controller sram size in word */
> +#define CQSPI_REG_SRAM_RESV_WORDS		2
> +#define CQSPI_REG_SRAM_PARTITION_WR		1
> +#define CQSPI_REG_SRAM_THRESHOLD_BYTES		50
> +
> +/* Instruction type */
> +#define CQSPI_INST_TYPE_SINGLE			0
> +#define CQSPI_INST_TYPE_DUAL			1
> +#define CQSPI_INST_TYPE_QUAD			2
> +#define CQSPI_DUMMY_CLKS_PER_BYTE		8
> +#define CQSPI_DUMMY_BYTES_MAX			4
> +#define CQSPI_STIG_DATA_LEN_MAX			8
> +#define CQSPI_INDIRECTTRIGGER_ADDR_MASK		0xFFFFF
> +
> +/* Register map */
> +#define	CQSPI_REG_CONFIG			0x00
> +#define	CQSPI_REG_CONFIG_ENABLE_MASK		BIT(0)
> +#define	CQSPI_REG_CONFIG_DIRECT_MASK		BIT(7)
> +#define	CQSPI_REG_CONFIG_DECODE_MASK		BIT(9)
> +#define	CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
> +#define CQSPI_REG_CONFIG_DMA_MASK		BIT(15)
> +#define	CQSPI_REG_CONFIG_BAUD_LSB		19
> +#define	CQSPI_REG_CONFIG_IDLE_LSB		31
> +#define	CQSPI_REG_CONFIG_CHIPSELECT_MASK	0xF
> +#define	CQSPI_REG_CONFIG_BAUD_MASK		0xF
> +#define	CQSPI_REG_RD_INSTR			0x04
> +#define	CQSPI_REG_RD_INSTR_OPCODE_LSB		0
> +#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB	8
> +#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB	12
> +#define	CQSPI_REG_RD_INSTR_TYPE_DATA_LSB	16
> +#define	CQSPI_REG_RD_INSTR_MODE_EN_LSB		20
> +#define	CQSPI_REG_RD_INSTR_DUMMY_LSB		24
> +#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK	0x3
> +#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK	0x3
> +#define	CQSPI_REG_RD_INSTR_TYPE_DATA_MASK	0x3
> +#define	CQSPI_REG_RD_INSTR_DUMMY_MASK		0x1F
> +#define	CQSPI_REG_WR_INSTR			0x08
> +#define	CQSPI_REG_WR_INSTR_OPCODE_LSB		0
> +#define	CQSPI_REG_WR_INSTR_TYPE_DATA_MASK	0x3
> +#define	CQSPI_REG_WR_INSTR_TYPE_DATA_LSB	16
> +#define	CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK	0x3
> +#define	CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB	12
> +
> +/*! Field WEL_DIS_FLD - wel_dis_fld */
> +#define CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS	8
> +#define CQSPI_REG_WR_COMPLETION_CTRL		0x38
> +#define CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS	14
> +
> +#define	CQSPI_REG_DELAY				0x0C
> +#define	CQSPI_REG_DELAY_TSLCH_LSB		0
> +#define	CQSPI_REG_DELAY_TCHSH_LSB		8
> +#define	CQSPI_REG_DELAY_TSD2D_LSB		16
> +#define	CQSPI_REG_DELAY_TSHSL_LSB		24
> +#define	CQSPI_REG_DELAY_TSLCH_MASK		0xFF
> +#define	CQSPI_REG_DELAY_TCHSH_MASK		0xFF
> +#define	CQSPI_REG_DELAY_TSD2D_MASK		0xFF
> +#define	CQSPI_REG_DELAY_TSHSL_MASK		0xFF
> +#define	CQSPI_REG_READCAPTURE			0x10
> +#define	CQSPI_REG_READCAPTURE_BYPASS_LSB	0
> +#define	CQSPI_REG_READCAPTURE_DELAY_LSB		1
> +#define	CQSPI_REG_READCAPTURE_DELAY_MASK	0xF
> +#define	CQSPI_REG_SIZE				0x14
> +#define	CQSPI_REG_SIZE_ADDRESS_LSB		0
> +#define	CQSPI_REG_SIZE_PAGE_LSB			4
> +#define	CQSPI_REG_SIZE_BLOCK_LSB		16
> +#define	CQSPI_REG_SIZE_ADDRESS_MASK		0xF
> +#define	CQSPI_REG_SIZE_PAGE_MASK		0xFFF
> +#define	CQSPI_REG_SIZE_BLOCK_MASK		0x3F
> +#define	CQSPI_REG_SRAMPARTITION			0x18
> +#define	CQSPI_REG_INDIRECTTRIGGER		0x1C
> +#define	CQSPI_REG_DMA				0x20
> +#define	CQSPI_REG_DMA_SINGLE_LSB		0
> +#define	CQSPI_REG_DMA_BURST_LSB			8
> +#define	CQSPI_REG_DMA_SINGLE_MASK		0xFF
> +#define	CQSPI_REG_DMA_BURST_MASK		0xFF
> +#define	CQSPI_REG_REMAP				0x24
> +#define	CQSPI_REG_MODE_BIT			0x28
> +#define	CQSPI_REG_SDRAMLEVEL			0x2C
> +#define	CQSPI_REG_SDRAMLEVEL_RD_LSB		0
> +#define	CQSPI_REG_SDRAMLEVEL_WR_LSB		16
> +#define	CQSPI_REG_SDRAMLEVEL_RD_MASK		0xFFFF
> +#define	CQSPI_REG_SDRAMLEVEL_WR_MASK		0xFFFF
> +
> +#define	CQSPI_REG_IRQSTATUS			0x40
> +#define	CQSPI_REG_IRQMASK			0x44
> +#define	CQSPI_REG_INDIRECTRD			0x60
> +#define	CQSPI_REG_INDIRECTRD_START_MASK		BIT(0)
> +#define	CQSPI_REG_INDIRECTRD_CANCEL_MASK	BIT(1)
> +#define	CQSPI_REG_INDIRECTRD_DONE_MASK		BIT(5)
> +#define	CQSPI_REG_INDIRECTRDWATERMARK		0x64
> +#define	CQSPI_REG_INDIRECTRDSTARTADDR		0x68
> +#define	CQSPI_REG_INDIRECTRDBYTES		0x6C
> +#define CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG	0x80
> +#define	CQSPI_REG_CMDCTRL			0x90
> +#define	CQSPI_REG_CMDCTRL_EXECUTE_MASK		BIT(0)
> +#define	CQSPI_REG_CMDCTRL_INPROGRESS_MASK	BIT(1)
> +#define	CQSPI_REG_CMDCTRL_WR_BYTES_LSB		12
> +#define	CQSPI_REG_CMDCTRL_WR_EN_LSB		15
> +#define	CQSPI_REG_CMDCTRL_ADD_BYTES_LSB		16
> +#define	CQSPI_REG_CMDCTRL_ADDR_EN_LSB		19
> +#define	CQSPI_REG_CMDCTRL_RD_BYTES_LSB		20
> +#define	CQSPI_REG_CMDCTRL_RD_EN_LSB		23
> +#define	CQSPI_REG_CMDCTRL_OPCODE_LSB		24
> +#define	CQSPI_REG_CMDCTRL_WR_BYTES_MASK		0x7
> +#define	CQSPI_REG_CMDCTRL_ADD_BYTES_MASK	0x3
> +#define	CQSPI_REG_CMDCTRL_RD_BYTES_MASK		0x7
> +#define	CQSPI_REG_INDIRECTWR			0x70
> +#define	CQSPI_REG_INDIRECTWR_START_MASK		BIT(0)
> +#define	CQSPI_REG_INDIRECTWR_CANCEL_MASK	BIT(1)
> +#define	CQSPI_REG_INDIRECTWR_DONE_MASK		BIT(5)
> +#define	CQSPI_REG_INDIRECTWRWATERMARK		0x74
> +#define	CQSPI_REG_INDIRECTWRSTARTADDR		0x78
> +#define	CQSPI_REG_INDIRECTWRBYTES		0x7C
> +#define	CQSPI_REG_CMDADDRESS			0x94
> +#define	CQSPI_REG_CMDREADDATALOWER		0xA0
> +#define	CQSPI_REG_CMDREADDATAUPPER		0xA4
> +#define	CQSPI_REG_CMDWRITEDATALOWER		0xA8
> +#define	CQSPI_REG_CMDWRITEDATAUPPER		0xAC
> +
> +/* Interrupt status bits */
> +#define CQSPI_REG_IRQ_MODE_ERR			BIT(0)
> +#define CQSPI_REG_IRQ_UNDERFLOW			BIT(1)
> +#define CQSPI_REG_IRQ_IND_COMP			BIT(2)
> +#define CQSPI_REG_IRQ_IND_RD_REJECT		BIT(3)
> +#define CQSPI_REG_IRQ_WR_PROTECTED_ERR		BIT(4)
> +#define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR		BIT(5)
> +#define CQSPI_REG_IRQ_WATERMARK			BIT(6)
> +#define CQSPI_REG_IRQ_IND_RD_OVERFLOW		BIT(12)
> +#define CQSPI_IRQ_STATUS_ERR		(CQSPI_REG_IRQ_MODE_ERR		| \
> +					 CQSPI_REG_IRQ_IND_RD_REJECT	| \
> +					 CQSPI_REG_IRQ_WR_PROTECTED_ERR	| \
> +					 CQSPI_REG_IRQ_ILLEGAL_AHB_ERR)
> +#define CQSPI_IRQ_MASK_RD		(CQSPI_REG_IRQ_MODE_ERR		| \
> +					 CQSPI_REG_IRQ_IND_RD_REJECT	| \
> +					 CQSPI_REG_IRQ_WATERMARK	| \
> +					 CQSPI_REG_IRQ_IND_RD_OVERFLOW	| \
> +					 CQSPI_REG_IRQ_IND_COMP)
> +#define CQSPI_IRQ_MASK_WR		(CQSPI_REG_IRQ_MODE_ERR		| \
> +					 CQSPI_REG_IRQ_WR_PROTECTED_ERR	| \
> +					 CQSPI_REG_IRQ_IND_COMP		| \
> +					 CQSPI_REG_IRQ_WATERMARK	| \
> +					 CQSPI_REG_IRQ_UNDERFLOW)
> +
> +#define CQSPI_IRQ_STATUS_MASK			(0xFFFFFFFF)
> +#define CQSPI_REG_IS_IDLE(base)					\
> +		((readl(base + CQSPI_REG_CONFIG) >>		\
> +			CQSPI_REG_CONFIG_IDLE_LSB) & 0x1)
> +#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns)		\
> +		((((tdelay_ns) - (tsclk_ns)) / (tref_ns)))
> +#define CQSPI_GET_RD_SRAM_LEVEL(reg_basse)			\
> +		(((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >>	\
> +		CQSPI_REG_SDRAMLEVEL_RD_LSB) & CQSPI_REG_SDRAMLEVEL_RD_MASK)
> +
> +struct cqspi_flash_pdata {
> +	u32	page_size;
> +	u32	block_size;
> +	u32	flash_type;
> +	u32	quad;
> +	u32	read_delay;
> +	u32	tshsl_ns;
> +	u32	tsd2d_ns;
> +	u32	tchsh_ns;
> +	u32	tslch_ns;
> +};
> +
> +struct cqspi_platform_data {
> +	u32	bus_num;
> +	u32	num_chipselect;
> +	u32	qspi_ahb_phy;
> +	u32	qspi_ahb_size;
> +	u32	qspi_ahb_mask;
> +	u32	master_ref_clk_hz;
> +	u32	ext_decoder;
> +	u32	fifo_depth;
> +	u32	enable_dma;
> +	u32	tx_dma_peri_id;
> +	u32	rx_dma_peri_id;
> +	u32	trigger_address;
> +	bool	is_decoded_cs;
> +	bool	rclk_en;
> +	struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIP_SELECT];
> +};
> +
> +struct struct_cqspi {
> +	struct platform_device	*pdev;
> +
> +	struct clk		*clk;
> +	struct clk		*fpi_clk;
> +
> +	struct reset_control	*reset;
> +	struct completion	transfer_complete;
> +	struct workqueue_struct	*workqueue;
> +	wait_queue_head_t	waitqueue;
> +	/* mutex lock for synchronization */
> +	struct mutex		lock;
> +
> +	void __iomem		*iobase;
> +	void __iomem		*qspi_ahb_virt;
> +	struct resource		*res;
> +	struct resource		*res_ahb;
> +	resource_size_t		ahb_size;
> +
> +	struct dma_chan		*rx_chan;
> +	struct completion       rx_dma_complete;
> +	dma_addr_t		mmap_phys_base;
> +	int			dma_done;
> +	u32			trigger_address;
> +	u32			wr_delay;
> +	u32			irq_status;
> +	int			current_cs;
> +	int			irq;
> +	bool			dac_mode;
> +};
> +
> +struct spi_mem_op_cadence {
> +	const void	*tx_buf;
> +	void		*rx_buf;
> +	u32		len;
> +	u32		tx_nbits:3;
> +	u32		rx_nbits:3;
> +};
> +
> +#endif /* __CADENCE_QSPI__H__ */
>

Ramuthevar,Vadivel MuruganX Nov. 11, 2019, 7:32 a.m. UTC | #2

Hi Vignesh,

    Thanks for review comments, sorry for the late reply since I was in 
one week vacation.

On 7/11/2019 1:44 PM, Vignesh Raghavendra wrote:
>
> On 30/10/19 1:41 PM, Ramuthevar,Vadivel MuruganX wrote:
>> From: Ramuthevar Vadivel Murugan <[e-mail]>
>>
>> Add support for the Cadence QSPI controller. This controller is
>> present in the Intel Lightning Mountain(LGM) SoCs, Altera and TI SoCs.
>> This driver has been tested on the Intel LGM SoCs.
>>
>> This driver does not support generic SPI and also the implementation
>> only supports spi-mem interface to replace the existing driver in
>> mtd/spi-nor/cadence-quadspi.c, the existing driver only support SPI-NOR
>> flash memory.
>>
>> Signed-off-by: Ramuthevar Vadivel Murugan <[e-mail]>
>> ---
>>   drivers/spi/Kconfig               |   10 +
>>   drivers/spi/Makefile              |    1 +
>>   drivers/spi/spi-cadence-quadspi.c | 1290 +++++++++++++++++++++++++++++++++++++
>>   drivers/spi/spi-cadence-quadspi.h |  272 ++++++++
>>   4 files changed, 1573 insertions(+)
>>   create mode 100644 drivers/spi/spi-cadence-quadspi.c
>>   create mode 100644 drivers/spi/spi-cadence-quadspi.h
>>
>> diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
>> index 6f7fdcbb9151..ef4d961feb54 100644
>> --- a/drivers/spi/Kconfig
>> +++ b/drivers/spi/Kconfig
>> @@ -192,6 +192,16 @@ config SPI_CADENCE
>>   	  This selects the Cadence SPI controller master driver
>>   	  used by Xilinx Zynq and ZynqMP.
>>   
>> +config SPI_CADENCE_QUADSPI
>> +	tristate "Cadence Quad SPI controller"
>> +	depends on OF && (ARM || ARM64 || COMPILE_TEST || X86)
>> +	depends on MTD || MTD_SPI_NOR || MTD_SPI_NAND
>> +	help
>> +	  Cadence QSPI is a specialized controller for connecting an SPI
>> +	  Flash over 1/2/4-bit wide bus. This enables support for the Quad SPI
> Supports Octal mode as well. So its 1/2/4/8-bit wide
Agreed!, will add it.
>> +	  controller in master mode. This driver does not support generic SPI.
>> +	  The implementation only supports spi-mem interface.
>> +
>>   config SPI_CLPS711X
>>   	tristate "CLPS711X host SPI controller"
>>   	depends on ARCH_CLPS711X || COMPILE_TEST
>> diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
>> index bb49c9e6d0a0..84a59d75a13a 100644
>> --- a/drivers/spi/Makefile
>> +++ b/drivers/spi/Makefile
>> @@ -29,6 +29,7 @@ obj-$(CONFIG_SPI_BCM_QSPI)		+= spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.
>>   obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
>>   obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
>>   obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
>> +obj-$(CONFIG_SPI_CADENCE_QUADSPI)		+= spi-cadence-quadspi.o
>>   obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
>>   obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
>>   obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
>> diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
>> new file mode 100644
>> index 000000000000..bca391bfb58f
>> --- /dev/null
>> +++ b/drivers/spi/spi-cadence-quadspi.c
>> @@ -0,0 +1,1290 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Driver for Cadence QSPI Controller
>> + *
>> + * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
>> + * Copyright Intel Corporation (C) 2019. All rights reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms and conditions of the GNU General Public License,
>> + * version 2, as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope it will be useful, but WITHOUT
>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
>> + * more details.
>> + *
>> + * You should have received a copy of the GNU General Public License along with
>> + * this program.  If not, see <http://www.gnu.org/licenses/>.
>> + */
>> +#include <linux/clk.h>
>> +#include <linux/completion.h>
>> +#include <linux/delay.h>
>> +#include <linux/dma-mapping.h>
>> +#include <linux/dmaengine.h>
>> +#include <linux/errno.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/jiffies.h>
>> +#include <linux/kernel.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>> +#include <linux/of.h>
>> +#include <linux/of_platform.h>
>> +#include <linux/of_address.h>
>> +#include <linux/of_irq.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/spi/spi.h>
>> +#include <linux/spi/spi-mem.h>
>> +#include <linux/unaligned/be_byteshift.h>
>> +
>> +#include "spi-cadence-quadspi.h"
>> +
>> +/* Quirks */
>> +#define CQSPI_NEEDS_WR_DELAY		BIT(0)
>> +#define CQSPI_DISABLE_DAC_MODE		BIT(1)
>> +
>> +#define CADENCE_QSPI_NAME                       "cadence-qspi"
>> +
>> +struct cqspi_driver_platdata {
>> +	u32 hwcaps_mask;
>> +	u8 quirks;
>> +};
>> +
>> +unsigned int cadence_qspi_init_timeout(const unsigned long timeout_in_ms)
>> +{
>> +	return jiffies + msecs_to_jiffies(timeout_in_ms);
>> +}
>> +
>> +unsigned int cadence_qspi_check_timeout(const unsigned long timeout)
>> +{
>> +	return time_before(jiffies, timeout);
>> +}
>> +
>> +static irqreturn_t cadence_qspi_irq_handler(int this_irq, void *dev)
>> +{
>> +	struct struct_cqspi *cadence_qspi = dev;
>> +	u32 irq_status;
>> +
>> +	/* Read interrupt status */
>> +	irq_status = readl(cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
>> +	if (!irq_status)
>> +		return IRQ_HANDLED;
>> +
>> +	cadence_qspi->irq_status = irq_status;
>> +
>> +	/* Clear interrupt */
>> +	writel(irq_status, cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
>> +	if (irq_status)
>> +		complete(&cadence_qspi->transfer_complete);
>> +
>> +	return IRQ_HANDLED;
>> +}
>> +
>> +static u32 cadence_qspi_cmd2addr(const unsigned char *addr_buf, u32 addr_width)
>> +{
>> +	unsigned int addr = 0;
>> +	int i;
>> +
>> +	/* Invalid address return zero. */
>> +	if (addr_width > 4)
>> +		return 0;
>> +
>> +	for (i = 0; i < addr_width; i++) {
>> +		addr = addr << 8;
>> +		addr |= addr_buf[i];
>> +	}
>> +
>> +	return addr;
>> +}
>> +
>> +void enable_qspi_direct_access(void *reg_base, bool enable)
>> +{
> Please be consistent with function names. Start all functions with
> cadence_qspi_. If need you could have a shorter function prefix like cqspi_
>
> Also, this and few other functions below can be static and they are not
> used outside of this module.
sure,  will fix it next patch-set.
>> +	u32 reg;
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
>> +	if (enable)
>> +		reg |= CQSPI_REG_CONFIG_DIRECT_MASK;
>> +	else
>> +		reg &= ~CQSPI_REG_CONFIG_DIRECT_MASK;
>> +
>> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
>> +}
>> +
>> +void cadence_qspi_controller_enable(void *reg_base, bool enable)
>> +{
>> +	unsigned int reg;
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
>> +	if (enable)
>> +		reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
>> +	else
>> +		reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
>> +
>> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
>> +}
>> +
>> +static unsigned int cadence_qspi_wait_idle(void *reg_base)
>> +{
>> +	u32 timeout, count = 0;
>> +
>> +	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
>> +	while (cadence_qspi_check_timeout(timeout)) {
>> +		if (CQSPI_REG_IS_IDLE(reg_base)) {
>> +			count++;
>> +			if (count >= CQSPI_POLL_IDLE_RETRY)
>> +				return 1;
>> +		} else {
>> +			count = 0;
>> +		}
>> +	}
>> +
>> +	return 0;
>> +}
>> +
> Could you please keep polling routines from original driver
> (drivers/mtd/spi-nor/cadence-quadspi.c). If you really want to improve
> these helpers, please do those changes in a separate patch later on in
> the series. This will greatly help in reviewing the code.
>
> Also, I see that you have dropped many inline comments in the code.
> These comments are quite important and I suggest not to drop them unless
> they are no longer applicable

surely we will keep the polling routines and also as per your suggestion 
later will add the performance related patches.

To reduce the code size, removed the comments, will keep it.

>> +static void cadence_qspi_readdata_capture(void *reg_base, u32 bypass, u32 delay)
>> +{
>> +	unsigned int reg;
>> +
>> +	cadence_qspi_controller_enable(reg_base, 0);
>> +
>> +	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
>> +	if (bypass)
>> +		reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
>> +	else
>> +		reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
>> +
>> +	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
>> +		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
>> +	reg |= ((delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
>> +		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
>> +	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
>> +
>> +	cadence_qspi_controller_enable(reg_base, 1);
>> +}
>> +
>> +static void cadence_qspi_config_baudrate_div(void *reg_base, u32 ref_clk_hz,
>> +					     u32 sclk_hz)
>> +{
>> +	unsigned int reg, div;
>> +
>> +	/* Recalculate the baudrate divisor based on QSPI specification. */
>> +	div = DIV_ROUND_UP(ref_clk_hz, 2 * sclk_hz) - 1;
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
>> +	reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);
>> +	div = (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB;
>> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
>> +}
>> +
>> +static void cadence_qspi_cs(void *reg_base, u32 chip_select, u32 decoder_enable)
>> +{
>> +	unsigned int reg;
>> +
>> +	cadence_qspi_controller_enable(reg_base, 0);
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
>> +	/* docoder */
> s/docoder/decoder
correct, the typo error
>> +	if (decoder_enable) {
>> +		reg |= CQSPI_REG_CONFIG_DECODE_MASK;
>> +	} else {
>> +		reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
>> +		chip_select = 0xF & ~(1 << chip_select);
>> +	}
>> +	reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
>> +			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB);
>> +	reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
>> +			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB;
>> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
>> +	cadence_qspi_controller_enable(reg_base, 1);
>> +}
>> +
>> +static int cadence_qspi_exec_flash_cmd(void *reg_base, unsigned int reg)
>> +{
>> +	unsigned int timeout;
>> +
>> +	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
>> +	reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
>> +	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
>> +
>> +	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
>> +	while (cadence_qspi_check_timeout(timeout)) {
>> +		reg = readl(reg_base + CQSPI_REG_CMDCTRL) &
>> +			CQSPI_REG_CMDCTRL_INPROGRESS_MASK;
>> +		if (!reg)
>> +			break;
>> +	}
>> +
> Please use cqspi_wait_for_bit() that uses readl_relaxed_poll_timeout()
> here. There are couple corner cases that above code does not take care of.
sure, fix it
>> +	if (!cadence_qspi_wait_idle(reg_base) || reg != 0)
>> +		return -EIO;
>> +
>> +	return 0;
>> +}
>> +
>> +static int cqspi_command_read(void *reg_base, u32 txlen, const u_char *txbuf,
>> +			      u32 addrlen, const u8 *addrbuf, u32 rxlen,
>> +			      u8 *rxbuf, u32 flash_type)
>> +{
>> +	u32 addr_value, read_len, reg;
>> +	int ret;
>> +
>> +	if (!rxlen || rxlen > CQSPI_STIG_DATA_LEN_MAX || !rxbuf)
>> +		return -EINVAL;
>> +
>> +	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
>> +	reg |= BIT(CQSPI_REG_CMDCTRL_RD_EN_LSB);
>> +
>> +	if (addrlen) {
>> +		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
>> +		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
>> +			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
>> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
>> +		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
>> +	}
>> +	/* 0 means 1 byte. */
>> +	reg |= (((rxlen - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
>> +		<< CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
>> +	ret = cadence_qspi_exec_flash_cmd(reg_base, reg);
>> +	if (ret != 0)
>> +		return ret;
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER);
>> +	read_len = (rxlen > 4) ? 4 : rxlen;
>> +	memcpy(rxbuf, &reg, read_len);
>> +	rxbuf += read_len;
>> +
>> +	if (rxlen > 4) {
>> +		reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER);
>> +		read_len = rxlen - read_len;
>> +		memcpy(rxbuf, &reg, read_len);
>> +	}
>> +
>> +	return 0;
>> +}
>> +
>> +static int cqspi_command_write(void *reg_base, u32 txlen, const u8 *txbuf,
>> +			       u32 addrlen, const u8 *addrbuf, u32 datalen,
>> +			       const u8 *databuf, u32 flash_type)
>> +{
>> +	unsigned int addr_value, reg, data = 0;
>> +
>> +	if (!txlen || !txbuf)
>> +		return -EINVAL;
>> +
>> +	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
>> +	if (datalen != 0) {
>> +		reg |= BIT(CQSPI_REG_CMDCTRL_WR_EN_LSB);
>> +		reg |= ((datalen - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
>> +			<< CQSPI_REG_CMDCTRL_WR_BYTES_LSB;
>> +		memcpy(&data, databuf, datalen);
>> +		writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER);
>> +	}
>> +	if (addrlen) {
>> +		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
>> +		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
>> +			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
>> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
>> +		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
>> +	}
>> +
>> +	return cadence_qspi_exec_flash_cmd(reg_base, reg);
>> +}
>> +
>> +static int cqspi_indirect_read_setup(void *reg_base, u32 txlen, const u8 *txbuf,
>> +				     u32 addrlen, const u8 *addrbuf,
>> +				     u32 dummy_bytes, u32 flash_type,
>> +				     u32 quad_mode)
>> +{
>> +	unsigned int addr_value, dummy_clk, reg;
>> +
>> +	if (addrlen) {
>> +		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
>> +		writel(addr_value, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
>> +	}
>> +
>> +	reg = txbuf[0] << CQSPI_REG_RD_INSTR_OPCODE_LSB;
>> +	reg |= (quad_mode & CQSPI_REG_RD_INSTR_TYPE_DATA_MASK) <<
>> +		CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
>> +
>> +	if (dummy_bytes) {
>> +		if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
>> +			dummy_bytes = CQSPI_DUMMY_BYTES_MAX;
>> +		reg |= BIT(CQSPI_REG_RD_INSTR_MODE_EN_LSB);
>> +		writel(0xFF, reg_base + CQSPI_REG_MODE_BIT);
>> +		dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
>> +		dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;
>> +		if (dummy_clk)
>> +			reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
>> +				<< CQSPI_REG_RD_INSTR_DUMMY_LSB;
>> +	} else if (flash_type == QSPI_FLASH_TYPE_NAND) {
>> +		reg |= ((1 * CQSPI_DUMMY_CLKS_PER_BYTE)
>> +				<< CQSPI_REG_RD_INSTR_DUMMY_LSB);
>> +	}
> Why do we need flash type specific handling here? Does not spi-nand
> driver provide appropriate dummy_clk values? Why is the driver always
> adding 8 dummy clks always?
On our board, this needs dummy clocks to work spi-nand, will 
differentiate and add in the init part instead of

cqspi_indirect_read_setup.

>> +	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
>> +	/* Set device size */
>> +	reg = readl(reg_base + CQSPI_REG_SIZE);
>> +	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
>> +	reg |= (addrlen - 1);
>> +	writel(reg, reg_base + CQSPI_REG_SIZE);
>> +	/* disable auto-polling */
>> +	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
>> +	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
>> +	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
>> +
>> +	return 0;
>> +}
>> +
>> +static void cqspi_request_mmap_dma(struct struct_cqspi *cqspi)
>> +{
>> +	dma_cap_mask_t mask;
>> +
>> +	dma_cap_zero(mask);
>> +	dma_cap_set(DMA_MEMCPY, mask);
>> +
>> +	cqspi->rx_chan = dma_request_chan_by_mask(&mask);
>> +	if (IS_ERR(cqspi->rx_chan)) {
>> +		dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
>> +		cqspi->rx_chan = NULL;
>> +	}
>> +	init_completion(&cqspi->rx_dma_complete);
>> +}
>> +
>> +static void cqspi_rx_dma_callback(void *param)
>> +{
>> +	struct struct_cqspi *cqspi = param;
>> +
>> +	complete(&cqspi->rx_dma_complete);
>> +}
>> +
>> +static int cqspi_direct_read_execute(struct struct_cqspi *cqspi, u8 *buf,
>> +				     const u8 *addrbuf, size_t rxlen)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct device *dev = &pdev->dev;
>> +	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
>> +	dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + addrbuf[0];
>> +	void __iomem *ahb_base = cqspi->qspi_ahb_virt;
>> +	int ret = 0;
>> +	struct dma_async_tx_descriptor *tx;
>> +	dma_cookie_t cookie;
>> +	dma_addr_t dma_dst;
>> +
>> +	if (!cqspi->rx_chan || !virt_addr_valid(buf)) {
>> +		memcpy_fromio(buf, ahb_base + addrbuf[0], rxlen);
>> +		return 0;
>> +	}
>> +
>> +	dma_dst = dma_map_single(dev, buf, rxlen, DMA_FROM_DEVICE);
>> +	if (dma_mapping_error(dev, dma_dst)) {
>> +		dev_err(dev, "dma mapping failed\n");
>> +		return -ENOMEM;
>> +	}
>> +	tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src,
>> +				       rxlen, flags);
>> +	if (!tx) {
>> +		dev_err(dev, "device_prep_dma_memcpy error\n");
>> +		ret = -EIO;
>> +		goto err_unmap;
>> +	}
>> +
>> +	tx->callback = cqspi_rx_dma_callback;
>> +	tx->callback_param = cqspi;
>> +	cookie = tx->tx_submit(tx);
>> +	reinit_completion(&cqspi->rx_dma_complete);
>> +
>> +	ret = dma_submit_error(cookie);
>> +	if (ret) {
>> +		dev_err(dev, "dma_submit_error %d\n", cookie);
>> +		ret = -EIO;
>> +		goto err_unmap;
>> +	}
>> +
>> +	dma_async_issue_pending(cqspi->rx_chan);
>> +	if (!wait_for_completion_timeout(&cqspi->rx_dma_complete,
>> +					 msecs_to_jiffies(rxlen))) {
>> +		dmaengine_terminate_sync(cqspi->rx_chan);
>> +		dev_err(dev, "DMA wait_for_completion_timeout\n");
>> +		ret = -ETIMEDOUT;
>> +		goto err_unmap;
>> +	}
>> +
>> +err_unmap:
>> +	dma_unmap_single(dev, dma_dst, rxlen, DMA_FROM_DEVICE);
>> +
>> +	return ret;
>> +}
>> +
>> +static int cqspi_indirect_read_execute(struct struct_cqspi *cqspi, u32 rxlen,
>> +				       u8 *rxbuf, u32 flash_type)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	void *reg_base = cqspi->iobase;
>> +	void *ahb_base = cqspi->qspi_ahb_virt;
>> +	u8 *rxbuf_end = rxbuf + rxlen;
>> +	u32 mod_bytes = rxlen % 4;
>> +	u32 bytes_to_read = 0;
>> +	int remaining = (int)rxlen;
>> +	u32 timeout, reg = 0;
>> +	int ret = 0;
>> +
>> +	writel(0, reg_base + CQSPI_REG_INDIRECTRDWATERMARK);
>> +	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
>> +	writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
>> +
>> +	mb();/* flush previous writes */
>> +
>> +	writel(pdata->fifo_depth - CQSPI_REG_SRAM_RESV_WORDS,
>> +	       reg_base + CQSPI_REG_SRAMPARTITION);
>> +	/* Clear all interrupts. */
>> +	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
>> +	writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
>> +
>> +	reinit_completion(&cqspi->transfer_complete);
>> +	writel(CQSPI_REG_INDIRECTRD_START_MASK,
>> +	       reg_base + CQSPI_REG_INDIRECTRD);
>> +
>> +	while (remaining > 0) {
>> +		bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
>> +
>> +		while (bytes_to_read != 0) {
>> +			unsigned int word_remain = round_down(remaining, 4);
>> +
>> +			bytes_to_read *= CQSPI_FIFO_WIDTH;
>> +			bytes_to_read = bytes_to_read > remaining ?
>> +						remaining : bytes_to_read;
>> +			bytes_to_read = round_down(bytes_to_read, 4);
>> +			if (bytes_to_read) {
>> +				ioread32_rep(ahb_base, rxbuf,
>> +					     (bytes_to_read / 4));
>> +			} else if (!word_remain && mod_bytes) {
>> +				unsigned int temp = ioread32(ahb_base);
>> +
>> +				bytes_to_read = mod_bytes;
>> +				memcpy(rxbuf, &temp, min((unsigned int)
>> +				       (rxbuf_end - rxbuf), bytes_to_read));
>> +			}
>> +
>> +			rxbuf += bytes_to_read;
>> +			remaining -= bytes_to_read;
>> +			bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
>> +		}
>> +
>> +		if (remaining < 0)
>> +			reinit_completion(&cqspi->transfer_complete);
>> +	}
>> +
>> +	/* Check indirect done status */
>> +	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
>> +	while (cadence_qspi_check_timeout(timeout)) {
>> +		reg = readl(reg_base + CQSPI_REG_INDIRECTRD);
>> +		if (reg & CQSPI_REG_INDIRECTRD_DONE_MASK)
>> +			break;
>> +	}
>> +	if (!(reg & CQSPI_REG_INDIRECTRD_DONE_MASK)) {
>> +		dev_err(&pdev->dev, "QSPI : Indirect read error %x\n", reg);
>> +		ret = -ETIMEDOUT;
>> +		goto failrd;
>> +	}
>> +	/* Disable interrupt */
>> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
>> +	/* Clear indirect completion status */
>> +	writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD);
>> +
>> +	return 0;
>> +failrd:
>> +	/* Disable interrupt */
>> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
>> +	/* Cancel the indirect read */
>> +	writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
>> +	       reg_base + CQSPI_REG_INDIRECTRD);
>> +	return ret;
>> +}
>> +
>> +static int cqspi_indirect_write_setup(void *reg_base, u32 txlen,
>> +				      const u8 *txbuf, u32 addrlen,
>> +				      const u8 *addrbuf, u32 flash_type,
>> +				      u32 quad_mode)
>> +{
>> +	unsigned int reg;
>> +
>> +	if (!txbuf)
>> +		return -EINVAL;
>> +
>> +	reg = readl(reg_base + CQSPI_REG_CONFIG);
>> +	reg &= ~(CQSPI_REG_CONFIG_DIRECT_MASK);
>> +	reg &= ~(CQSPI_REG_CONFIG_DMA_MASK);
>> +	writel(reg, reg_base + CQSPI_REG_CONFIG);
>> +
>> +	/* Set opcode. */
>> +	reg = txbuf[0] << CQSPI_REG_WR_INSTR_OPCODE_LSB;
>> +	reg |= BIT(CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS);
>> +	if (txbuf[0] == MACRONIX_4PP_CMD && flash_type == QSPI_FLASH_TYPE_NOR &&
>> +	    quad_mode == QUAD_QIO) {
>> +		/* Configure the quad */
>> +		reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK) <<
>> +		       CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
>> +	}
> Nope, no custom handling or interpreting of opcodes in driver.
> Just set addrwidth to quad in CQSPI_REG_WR_INSTR when op->addr.buswidth
> is 4.
Agreed!, add it in the next patch.
>
>> +	/* Configure the quad */
>> +	reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_DATA_MASK) <<
>> +	       CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
>> +	writel(reg, reg_base + CQSPI_REG_WR_INSTR);
>> +	/* Setup write address. */
>> +	reg = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
>> +	writel(reg, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR);
>> +	reg = readl(reg_base + CQSPI_REG_SIZE);
>> +	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
>> +	reg |= ((addrlen - 1) & CQSPI_REG_SIZE_ADDRESS_MASK);
>> +	writel(reg, reg_base +  CQSPI_REG_SIZE);
>> +
>> +	/* disable auto-polling */
>> +	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
>> +	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
>> +	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
>> +
>> +	return 0;
>> +}
>> +
>> +static int cqspi_indirect_write_execute(struct struct_cqspi *cqspi, u32 txlen,
>> +					const u8 *txbuf, u32 flash_type)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	struct cqspi_flash_pdata *f_pdata =
>> +			&pdata->f_pdata[cqspi->current_cs];
>> +	void *reg_base = cqspi->iobase;
>> +	void *ahb_base = cqspi->qspi_ahb_virt;
>> +	u32 *irq_status = &cqspi->irq_status;
>> +	u32 page_size = f_pdata->page_size;
>> +	u32 write_bytes, timeout, reg = 0;
>> +	int remaining = (int)txlen;
>> +	int ret;
>> +
>> +	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
>> +	writel(0x0, reg_base + CQSPI_REG_INDIRECTWRWATERMARK);
>> +	reg = readl(reg_base + CQSPI_REG_SIZE);
>> +	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
>> +	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
>> +	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
>> +	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
>> +	writel(reg, reg_base +  CQSPI_REG_SIZE);
>> +
>> +	writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
>> +	writel(CQSPI_REG_SRAM_PARTITION_WR, reg_base + CQSPI_REG_SRAMPARTITION);
>> +	/* Clear all interrupts. */
>> +	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
>> +	writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK);
>> +	reinit_completion(&cqspi->transfer_complete);
>> +	writel(CQSPI_REG_INDIRECTWR_START_MASK,
>> +	       reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> +	if (cqspi->wr_delay)
>> +		ndelay(cqspi->wr_delay);
>> +
>> +	while (remaining > 0) {
>> +		size_t write_words, mod_bytes;
>> +
>> +		write_bytes = remaining > page_size ? page_size : remaining;
>> +		write_words = write_bytes / 4;
>> +		mod_bytes = write_bytes % 4;
>> +
>> +		if (write_words) {
>> +			iowrite32_rep(ahb_base, txbuf, write_words);
>> +			txbuf += (write_words * 4);
>> +		}
>> +		if (mod_bytes) {
>> +			unsigned int temp = 0xFFFFFFFF;
>> +
>> +			memcpy(&temp, txbuf, mod_bytes);
>> +			iowrite32(temp, ahb_base);
>> +			txbuf += mod_bytes;
>> +		}
>> +		ret = wait_event_interruptible_timeout(cqspi->waitqueue,
>> +						       *irq_status &
>> +						       CQSPI_IRQ_MASK_WR,
>> +						       CQSPI_TIMEOUT_MS);
> This was wait_for_completion_timeout() previously. Have you tested
> interrupting the sleep and verified that driver handles this case correctly?
Yes I have tested, align with

wait_for_completion_timeout

>> +		if (!(ret) & (*irq_status & CQSPI_IRQ_STATUS_ERR)) {
>> +			ret = -ETIMEDOUT;
>> +			goto failwr;
>> +		} else {
>> +			ret = 0;
>> +		}
>> +		remaining -= write_bytes;
>> +
>> +		if (remaining < 0)
>> +			reinit_completion(&cqspi->transfer_complete);
>> +	}
>> +
>> +	/* Check indirect done status */
>> +	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
>> +	while (cadence_qspi_check_timeout(timeout)) {
>> +		reg = readl(reg_base + CQSPI_REG_INDIRECTWR);
>> +		if (reg & CQSPI_REG_INDIRECTWR_DONE_MASK)
>> +			break;
>> +	}
>> +	if (!(reg & CQSPI_REG_INDIRECTWR_DONE_MASK)) {
>> +		dev_err(&pdev->dev, "QSPI: Indirect write error %x", reg);
>> +		ret = -ETIMEDOUT;
>> +		goto failwr;
>> +	}
>> +
>> +	return 0;
>> +
>> +failwr:
>> +	/* Disable interrupt. */
>> +	writel(0, reg_base + CQSPI_REG_IRQMASK);
>> +	/* Clear indirect completion status */
>> +	writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> +	/* Cancel the indirect write */
>> +	if (ret)
>> +		writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
>> +		       reg_base + CQSPI_REG_INDIRECTWR);
>> +
>> +	return ret;
>> +}
>> +
>> +unsigned int cadence_qspi_is_controller_ready(void *reg_base)
>> +{
>> +	return cadence_qspi_wait_idle(reg_base);
>> +}
>> +
>> +void cadence_qspi_controller_init(struct struct_cqspi *cqspi)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +
>> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
>> +
>> +	/* Configure the remap address register, no remap */
>> +	writel(0, cqspi->iobase + CQSPI_REG_REMAP);
>> +	/* Disable all interrupts. */
>> +	writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
>> +
>> +	/* DAC is disabled for Intel LGM SOC */
>> +	if (!cqspi->dac_mode) {
>> +		enable_qspi_direct_access(cqspi->iobase, 0);
>> +	} else {
>> +		enable_qspi_direct_access(cqspi->iobase, 1);
>> +		/* TODO: for TI platform to be enabled */
>> +		cqspi_request_mmap_dma(cqspi);
>> +	}
>> +
>> +	/* Load indirect trigger address. */
>> +	writel(pdata->trigger_address,
>> +	       cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER);
>> +
>> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +unsigned int calculate_ticks_for_ns(u32 ref_clk_hz, u32 ns_val)
>> +{
>> +	unsigned int ticks;
>> +
>> +	ticks = ref_clk_hz / 1000;      /* kHz */
>> +	ticks = DIV_ROUND_UP(ticks * ns_val, 1000000);
>> +
>> +	return ticks;
>> +}
>> +
>> +void cadence_qspi_delay(struct struct_cqspi *cqspi, u32 ref_clk, u32 sclk_hz)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cqspi->current_cs];
>> +	void __iomem *iobase = cqspi->iobase;
>> +	const unsigned int ref_clk_hz = pdata->master_ref_clk_hz;
>> +	unsigned int tshsl, tchsh, tslch, tsd2d;
>> +	unsigned int reg;
>> +	unsigned int tsclk;
>> +
>> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
>> +	/* calculate the number of ref ticks for one sclk tick */
>> +	tsclk = DIV_ROUND_UP(ref_clk_hz, sclk_hz);
>> +
>> +	/* this particular value must be at least one sclk */
>> +	if (tshsl < tsclk)
>> +		tshsl = tsclk;
>> +
>> +	tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns);
>> +	tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns);
>> +	tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns);
>> +
>> +	reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
>> +			<< CQSPI_REG_DELAY_TSHSL_LSB);
>> +	reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
>> +			<< CQSPI_REG_DELAY_TCHSH_LSB);
>> +	reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
>> +			<< CQSPI_REG_DELAY_TSLCH_LSB);
>> +	reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
>> +			<< CQSPI_REG_DELAY_TSD2D_LSB);
>> +	writel(reg, iobase + CQSPI_REG_DELAY);
>> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +void cadence_qspi_switch_chipselect(struct struct_cqspi *cqspi, u32 cs)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cs];
>> +	void __iomem *iobase = cqspi->iobase;
>> +	unsigned int reg;
>> +
>> +	cadence_qspi_controller_enable(cqspi->iobase, 0);
>> +	/* Configure page size and block size. */
>> +	reg = readl(iobase + CQSPI_REG_SIZE);
>> +	/* clear the previous value */
>> +	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
>> +	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
>> +	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
>> +	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
>> +	writel(reg, iobase + CQSPI_REG_SIZE);
>> +	/* configure the chip select */
>> +	cadence_qspi_cs(iobase, cs, pdata->ext_decoder);
>> +	cadence_qspi_controller_enable(cqspi->iobase, 1);
>> +}
>> +
>> +static int cadence_qspi_mem_process(struct struct_cqspi *cqspi,
>> +				    struct spi_mem *mem,
>> +				    const struct spi_mem_op *op)
>> +{
>> +	struct platform_device *pdev = cqspi->pdev;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	unsigned int tmpbufsize, n_trans = 0, totalxferlen = 0;
>> +	void __iomem *iobase = cqspi->iobase;
>> +	struct spi_mem_op_cadence ops[4] = { };
>> +	struct spi_mem_op_cadence *cmd_ops = NULL;
>> +	struct spi_mem_op_cadence *data_ops = NULL;
>> +	struct spi_mem_op_cadence *dummy_ops = NULL;
>> +	struct spi_mem_op_cadence *addr_ops = NULL;
>> +	struct cqspi_flash_pdata *f_pdata;
>> +	int rdid_length, mode, ret, i;
>> +	u8 *tmpbuf;
>> +	u32 sclk;
>> +
>> +	if (cqspi->current_cs != mem->spi->chip_select) {
>> +		cqspi->current_cs = mem->spi->chip_select;
>> +		cadence_qspi_switch_chipselect(cqspi, mem->spi->chip_select);
>> +	}
>> +
>> +	f_pdata = &pdata->f_pdata[cqspi->current_cs];
>> +	if (f_pdata->flash_type == QSPI_FLASH_TYPE_NOR)
>> +		rdid_length = 6;
>> +	else
>> +		rdid_length = 3;
>> +
> What? NACK... why should driver worry about rdid_length?
sorry forgot remove it.
>
>> +	tmpbufsize = sizeof(op->cmd.opcode) + op->addr.nbytes +
>> +			op->dummy.nbytes;
>> +
>> +	tmpbuf = kzalloc(tmpbufsize, GFP_KERNEL | GFP_DMA);
>> +	if (!tmpbuf)
>> +		return -ENOMEM;
>> +
>> +	tmpbuf[0] = op->cmd.opcode;
>> +	ops[n_trans].tx_buf = tmpbuf;
>> +	ops[n_trans].len = sizeof(op->cmd.opcode);
>> +	ops[n_trans].tx_nbits = op->cmd.buswidth;
>> +
>> +	n_trans++;
>> +	totalxferlen++;
>> +
>> +	if (op->addr.nbytes) {
>> +		int i;
>> +
>> +		for (i = 0; i < op->addr.nbytes; i++)
>> +			tmpbuf[i + 1] = op->addr.val >>
>> +					(8 * (op->addr.nbytes - i - 1));
>> +
>> +		ops[n_trans].tx_buf = tmpbuf + 1;
>> +		ops[n_trans].len = op->addr.nbytes;
>> +		ops[n_trans].tx_nbits = op->addr.buswidth;
>> +
>> +		n_trans++;
>> +		totalxferlen += op->addr.nbytes;
>> +	}
>> +	if (op->dummy.nbytes) {
>> +		memset(tmpbuf + op->addr.nbytes + 1, 0xff, op->dummy.nbytes);
>> +		ops[n_trans].tx_buf = tmpbuf + op->addr.nbytes + 1;
>> +		ops[n_trans].len = op->dummy.nbytes;
>> +		ops[n_trans].tx_nbits = op->dummy.buswidth;
>> +
>> +		n_trans++;
>> +		totalxferlen += op->dummy.nbytes;
>> +	}
>> +	if (op->data.nbytes) {
>> +		if (op->data.dir == SPI_MEM_DATA_IN) {
>> +			ops[n_trans].rx_buf = op->data.buf.in;
>> +			ops[n_trans].rx_nbits = op->data.buswidth;
>> +		} else {
>> +			ops[n_trans].tx_buf = op->data.buf.out;
>> +			ops[n_trans].tx_nbits = op->data.buswidth;
>> +		}
>> +
>> +		ops[n_trans].len = op->data.nbytes;
>> +		n_trans++;
>> +		totalxferlen += op->data.nbytes;
>> +	}
>> +
>> +	for (i = 0; i < n_trans; i++)
>> +		dev_dbg(&pdev->dev, "ops[%d] %d\n", i, ops[i].len);
>> +
>> +	switch (n_trans) {
>> +	case 1:
>> +		cmd_ops = &ops[0];
>> +		break;
>> +	case 2:
>> +		cmd_ops = &ops[0];
>> +		if (f_pdata->flash_type == QSPI_FLASH_TYPE_NAND) {
>> +			if (data_ops->rx_buf)
>> +				data_ops = &ops[1];
>> +			else
>> +				addr_ops = &ops[1];
>> +		} else {
>> +			data_ops = &ops[1];
>> +		}
>
> Please get ride of all flash type specific handling... There should be
> no need for it. IF there are gaps in then lets discuss and fix it in
> spi-nand and spi-nor frameworks and not in the driver.
>
> spi-mem user should just take spi_mem_op template passed by the core and
> execute it. No assumptions wrt flash type or opcode should be done.
sure, will take care flash type specific handling.
>> +		break;
>> +	case 3:
>> +		cmd_ops = &ops[0];
>> +		addr_ops = &ops[1];
>> +		data_ops = &ops[2];
>> +		break;
>> +	case 4:
>> +		cmd_ops = &ops[0];
>> +		addr_ops = &ops[1];
>> +		dummy_ops = &ops[2];
>> +		data_ops = &ops[3];
>> +		break;
>> +	default:
>> +		dev_err(&pdev->dev, "Unsupported n_trans %u\n", n_trans);
>> +		return -EINVAL;
>> +	}
>> +
>> +	if (!data_ops)
>> +		mode = STIG_WRITE_MODE;
>> +	else if (data_ops->len > rdid_length)
>> +		mode = data_ops->tx_buf ? IDC_WRITE_MODE : IDC_READ_MODE;
>> +	else
>> +		mode = data_ops->tx_buf ? STIG_WRITE_MODE : STIG_READ_MODE;
>> +
> Decision to use STIG was INDAC mode can be done using:
>
>          if (op->data.dir == SPI_MEM_DATA_IN && op->data.buf.in) {
>                  if (!op->addr.nbytes)
>                          mode = CQSPI_STIG_READ;
>                  else
>                          mode = IDC_READ_MODE;
>          } else {
>                  if (!op->addr.nbytes || !op->data.buf.out)
>                          mode = CQSPI_STIG_WRITE;
>                  else
>                          mode = IDC_WRITE_MODE;
>          }
>
> No need for rdid_length etc.
Thanks for the suggestion, i will update in the next patch-set.
>> +	sclk = mem->spi->max_speed_hz;
>> +	cadence_qspi_controller_enable(iobase, 0);
>> +	cadence_qspi_config_baudrate_div(iobase, pdata->master_ref_clk_hz,
>> +					 sclk);
>> +	cadence_qspi_delay(cqspi, pdata->master_ref_clk_hz, sclk);
>> +	cadence_qspi_readdata_capture(iobase, 1, f_pdata->read_delay);
>> +	cadence_qspi_controller_enable(iobase, 1);
>> +
>> +	/* execute transfer */
>> +	switch (mode) {
>> +	case STIG_WRITE_MODE:
>> +		ret = cqspi_command_write(iobase, cmd_ops->len, cmd_ops->tx_buf,
>> +					  addr_ops ? addr_ops->len : 0,
>> +					  addr_ops ? addr_ops->tx_buf : NULL,
>> +					  data_ops ? data_ops->len : 0,
>> +					  data_ops ? data_ops->tx_buf : NULL,
>> +					  f_pdata->flash_type);
>> +		break;
>> +	case STIG_READ_MODE:
>> +		ret = cqspi_command_read(iobase, cmd_ops->len, cmd_ops->tx_buf,
>> +					 addr_ops ? addr_ops->len : 0,
>> +					 addr_ops ? addr_ops->tx_buf : NULL,
>> +					 data_ops ? data_ops->len : 0,
>> +					 data_ops ? data_ops->rx_buf : NULL,
>> +					 f_pdata->flash_type);
>> +		break;
>> +	case IDC_WRITE_MODE:
>> +		ret = cqspi_indirect_write_setup(iobase, cmd_ops->len,
>> +						 cmd_ops->tx_buf,
>> +						 addr_ops ? addr_ops->len : 0,
>> +						 addr_ops ? addr_ops->tx_buf : 0,
>> +						 f_pdata->flash_type,
>> +						 f_pdata->quad);
>> +		ret = cqspi_indirect_write_execute(cqspi, data_ops->len,
>> +						   data_ops->tx_buf,
>> +						   f_pdata->flash_type);
>> +		break;
>> +	case IDC_READ_MODE:
>> +		ret = cqspi_indirect_read_setup(iobase, cmd_ops->len,
>> +						cmd_ops->tx_buf,
>> +						addr_ops ? addr_ops->len : 0,
>> +						addr_ops ? addr_ops->tx_buf : 0,
>> +						dummy_ops ? dummy_ops->len : 0,
>> +						f_pdata->flash_type,
>> +						f_pdata->quad);
>> +		ret = cqspi_indirect_read_execute(cqspi, data_ops->len,
>> +						  data_ops->rx_buf,
>> +						  f_pdata->flash_type);
>> +		/* TODO: for TI DMA + DAC to be enabled */
> This is a big gap and there is lot of code sharing that can be done b/w
> INDAC and DAC mode.
>
> Looks like driver isn't quite close to being ready. I suggest you also
> take a look at patches for spi-mem conversion of cadence-quadspi driver
> in U-Boot as well:
>
> https://patchwork.ozlabs.org/cover/1176362/

driver works perfectly on our platform, since we do not have DMA , just 
left the code.

I will add those part of code in the next series of patch.

>> +		break;
>> +	default:
>> +		dev_err(&pdev->dev, "Unsupported mode %u\n", mode);
>> +		return -EINVAL;
>> +	}
>> +
>> +	return ret;
>> +}
>> +
>> +int cadence_qspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
>> +{
>> +	struct struct_cqspi *cqspi = spi_master_get_devdata(mem->spi->master);
>> +	int ret;
>> +
>> +	mutex_lock(&cqspi->lock);
>> +	ret = cadence_qspi_mem_process(cqspi, mem, op);
>> +	if (ret)
>> +		dev_err(&mem->spi->dev, "Error: qspi transfer failed!!!.\n");
>> +	mutex_unlock(&cqspi->lock);
>> +
>> +	return ret;
>> +}
>> +
>> +static const struct spi_controller_mem_ops cadence_qspi_mem_ops = {
>> +	.exec_op = cadence_qspi_exec_mem_op,
>> +};
>> +
>> +static int cadence_qspi_setup(struct spi_device *spi)
>> +{
>> +	if (spi->chip_select > spi->master->num_chipselect) {
>> +		dev_err(&spi->dev, "%d CS is out of range\n", spi->chip_select);
>> +		return -EINVAL;
>> +	}
>> +	return 0;
>> +}
>> +
>> +static int cadence_qspi_of_get_pdata(struct platform_device *pdev)
>> +{
>> +	struct device_node *np = pdev->dev.of_node;
>> +	struct device_node *nc;
>> +	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
>> +	struct cqspi_flash_pdata *f_pdata;
>> +	unsigned int cs;
>> +	unsigned int prop;
>> +
>> +	pdata->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
>> +
>> +	if (of_property_read_u32(np, "cdns,trigger-address", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine trigger-address\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->trigger_address = prop;
>> +
>> +	pdata->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
>> +
>> +	if (of_property_read_u32(np, "cdns,qspi-phyaddr", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine cdns,qspi-phyaddr\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->qspi_ahb_phy = prop;
>> +
> Please dont add any new DT properties, there is no need for them. See
> how this was handled in existing driver and reuse it
Okay
>
>> +	if (of_property_read_u32(np, "cdns,qspi-physize", &prop)) {
>> +		dev_info(&pdev->dev, "missing cdns,qspi-physize to 128 kB\n");
>> +		prop = 128;
>> +	}
>> +	pdata->qspi_ahb_size = prop * 1024;
>> +
>> +	if (of_property_read_u32(np, "cdns,qspi-phymask", &prop))
>> +		prop = CQSPI_INDIRECTTRIGGER_ADDR_MASK;
>> +	pdata->qspi_ahb_mask = prop;
>> +
>> +	if (of_property_read_u32(np, "bus-num", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine bus-num\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->bus_num = prop;
>> +
>> +	if (of_property_read_u32(np, "num-chipselect", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine num-chipselect\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->num_chipselect = prop;
>> +
>> +	if (of_property_read_u32(np, "cdns,fifo-depth", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine fifo-depth\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->fifo_depth = prop;
>> +
>> +	if (of_property_read_u32(np, "ext-decoder", &prop)) {
>> +		dev_err(&pdev->dev, "couldn't determine ext-decoder\n");
>> +		return -ENXIO;
>> +	}
>> +	pdata->ext_decoder = prop;
>> +
>
>
>> +	pdata->enable_dma = of_property_read_bool(np, "dmas");
>> +	dev_info(&pdev->dev, "DMA %senabled\n", pdata->enable_dma ? "" : "NOT");
>> +
> Slave DMA was never supported and is not needed.
remove it.
>> +	/* Get flash devices platform data */
>> +	for_each_child_of_node(np, nc) {
>> +		if (!of_device_is_available(nc))
>> +			continue;
>> +
>> +		if (of_property_read_u32(nc, "reg", &cs)) {
>> +			dev_err(&pdev->dev, "couldn't determine reg\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata = &pdata->f_pdata[cs];
>> +
>> +		/* use compatible string to determine flash type */
>> +		if (of_device_is_compatible(nc, "spinand"))
>> +			f_pdata->flash_type = QSPI_FLASH_TYPE_NAND;
>> +		else
>> +			f_pdata->flash_type = QSPI_FLASH_TYPE_NOR;
>> +
>> +		if (of_property_read_u32(nc, "spi-rx-bus-width", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine quad\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->quad = (prop == 4) ? QUAD_QIO : QUAD_SIO;
>> +
>> +		if (of_property_read_u32(nc, "page-size", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine page-size\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->page_size = prop;
>> +
>> +		if (of_property_read_u32(nc, "block-size", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine block-size\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->block_size = prop;
>> +
>> +		if (of_property_read_u32(nc, "cdns,read-delay", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine read-delay\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->read_delay = prop;
>> +
>> +		if (of_property_read_u32(nc, "cdns,tshsl-ns", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine tshsl-ns\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->tshsl_ns = prop;
>> +
>> +		if (of_property_read_u32(nc, "cdns,tsd2d-ns", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->tsd2d_ns = prop;
>> +
>> +		if (of_property_read_u32(nc, "cdns,tchsh-ns", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine tchsh-ns\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->tchsh_ns = prop;
>> +
>> +		if (of_property_read_u32(nc, "cdns,tslch-ns", &prop)) {
>> +			dev_err(&pdev->dev, "couldn't determine tslch-ns\n");
>> +			return -ENXIO;
>> +		}
>> +		f_pdata->tslch_ns = prop;
>> +	}
>> +	return 0;
>> +}
>> +
>> +static int cadence_qspi_probe(struct platform_device *pdev)
>> +{
>> +	struct cqspi_platform_data *pdata;
>> +	struct device *dev = &pdev->dev;
>> +	struct struct_cqspi *cqspi;
>> +	struct spi_master *master;
>> +	struct reset_control *rstc, *rstc_ocp;
>> +	const struct cqspi_driver_platdata *ddata;
>> +	struct resource *res = NULL;
>> +	int ret;
>> +
>> +	master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
>> +	if (!master) {
>> +		dev_err(&pdev->dev, "spi_alloc_master failed\n");
>> +		return -ENOMEM;
>> +	}
>> +	master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA | SPI_TX_QUAD |
>> +				SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL;
> Octal?
Add it next patch .
>> +	master->setup = cadence_qspi_setup;
>> +	master->mem_ops = &cadence_qspi_mem_ops;
>> +	master->dev.of_node = pdev->dev.of_node;
>> +	cqspi = spi_master_get_devdata(master);
>> +	cqspi->pdev = pdev;
>> +
>> +	pdata = kmalloc(sizeof(*pdata), GFP_KERNEL);
>> +	if (!pdata) {
>> +		ret = -ENOMEM;
>> +		goto err_pdata;
>> +	}
>> +	pdev->dev.platform_data = pdata;
>> +
>> +	cqspi->clk = devm_clk_get(&pdev->dev, "qspi");
>> +	if (IS_ERR(cqspi->clk)) {
>> +		dev_err(&pdev->dev, "cannot get qspi clk\n");
>> +		return PTR_ERR(cqspi->clk);
>> +	}
>> +	pdata->master_ref_clk_hz = clk_get_rate(cqspi->clk);
>> +
>> +	ret = clk_prepare_enable(cqspi->clk);
>> +	if (ret < 0) {
>> +		dev_err(&pdev->dev, "failed to enable qspi clock: %d\n", ret);
>> +		return ret;
>> +	}
>> +
>> +	ret = cadence_qspi_of_get_pdata(pdev);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "Get platform data failed.\n");
>> +		return -ENODEV;
>> +	}
>> +
>> +	cqspi->res = res;
>> +	/* Obtain and remap controller address. */
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
>> +	cqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
>> +	if (IS_ERR(cqspi->iobase)) {
>> +		dev_err(dev, "Cannot remap controller address.\n");
>> +		return PTR_ERR(cqspi->iobase);
>> +	}
>> +
>> +	/* Obtain and remap AHB address. */
>> +	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
>> +	cqspi->qspi_ahb_virt = devm_ioremap_resource(dev, res);
>> +	if (IS_ERR(cqspi->qspi_ahb_virt)) {
>> +		dev_err(dev, "Cannot remap AHB address.\n");
>> +		return PTR_ERR(cqspi->qspi_ahb_virt);
>> +	}
>> +	cqspi->mmap_phys_base = (dma_addr_t)res->start;
>> +	cqspi->ahb_size = resource_size(res);
>> +
>> +	/* Obtain QSPI reset control */
>> +	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
>> +	if (IS_ERR(rstc)) {
>> +		dev_err(dev, "Cannot get QSPI reset.\n");
>> +		return PTR_ERR(rstc);
>> +	}
>> +
>> +	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
>> +	if (IS_ERR(rstc_ocp)) {
>> +		dev_err(dev, "Cannot get QSPI OCP reset.\n");
>> +		return PTR_ERR(rstc_ocp);
>> +	}
>> +
>> +	reset_control_assert(rstc);
>> +	reset_control_deassert(rstc);
>> +
>> +	reset_control_assert(rstc_ocp);
>> +	reset_control_deassert(rstc_ocp);
>> +
>> +	ddata  = of_device_get_match_data(dev);
>> +	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
>> +		cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
>> +						   pdata->master_ref_clk_hz);
>> +
>> +	init_completion(&cqspi->transfer_complete);
>> +
>> +	cqspi->irq = platform_get_irq(pdev, 0);
>> +	if (cqspi->irq < 0) {
>> +		dev_err(dev, "platform_get_irq failed.\n");
>> +		ret = -ENXIO;
>> +		goto err_irq;
>> +	}
>> +	ret = devm_request_irq(dev, cqspi->irq, cadence_qspi_irq_handler, 0,
>> +			       pdev->name, cqspi);
>> +	if (ret) {
>> +		dev_err(dev, "request_irq failed.\n");
>> +		goto err_irq;
>> +	}
>> +
>> +	master->bus_num = pdata->bus_num;
>> +	master->num_chipselect = pdata->num_chipselect;
>> +	mutex_init(&cqspi->lock);
>> +	platform_set_drvdata(pdev, master);
>> +	cadence_qspi_controller_init(cqspi);
>> +	cqspi->current_cs = 0;
>> +
>> +	ret = devm_spi_register_master(dev, master);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "devm_spi_register_master failed.\n");
>> +		goto err_of;
>> +	}
>> +
>> +	if (ddata && (ddata->quirks & CQSPI_DISABLE_DAC_MODE))
>> +		cqspi->dac_mode = false;
>> +
>> +	return 0;
>> +
>> +err_pdata:
>> +	kfree(pdata);
>> +err_irq:
>> +	free_irq(cqspi->irq, cqspi);
>> +err_of:
>> +	spi_master_put(master);
>> +	dev_err(&pdev->dev, "Cadence QSPI controller probe failed\n");
>> +	return ret;
>> +}
>> +
>> +static int cadence_qspi_remove(struct platform_device *pdev)
>> +{
>> +	struct spi_master *master = platform_get_drvdata(pdev);
>> +	struct struct_cqspi *cadence_qspi = spi_master_get_devdata(master);
>> +
>> +	cadence_qspi_controller_enable(cadence_qspi->iobase, 0);
>> +	platform_set_drvdata(pdev, NULL);
>> +	free_irq(cadence_qspi->irq, cadence_qspi);
>> +	iounmap(cadence_qspi->iobase);
>> +	iounmap(cadence_qspi->qspi_ahb_virt);
>> +	release_mem_region(cadence_qspi->res->start,
>> +			   resource_size(cadence_qspi->res));
>> +	kfree(pdev->dev.platform_data);
>> +	spi_unregister_master(master);
>> +	spi_master_put(master);
>> +	return 0;
>> +}
>> +
>> +static const struct cqspi_driver_platdata k2g_qspi = {
>> +	.quirks = CQSPI_NEEDS_WR_DELAY,
>> +};
>> +
>> +static const struct cqspi_driver_platdata am654_ospi = {
>> +	.quirks = CQSPI_NEEDS_WR_DELAY,
>> +};
>> +
>> +static const struct cqspi_driver_platdata intel_lgm_qspi = {
>> +	.quirks = CQSPI_DISABLE_DAC_MODE,
>> +};
>> +
>> +#ifdef CONFIG_OF
>> +static const struct of_device_id cadence_qspi_of_match[] = {
>> +	{
>> +		.compatible = "cadence,qspi",
>> +	},
>> +	{
>> +		.compatible = "ti,k2g-qspi",
>> +		.data = &k2g_qspi,
>> +	},
>> +	{
>> +		.compatible = "ti,am654-ospi",
>> +		.data = &am654_ospi,
>> +	},
>> +	{
>> +		.compatible = "intel,lgm-qspi",
>> +		.data = &intel_lgm_qspi,
>> +	},
>> +	{ /* end of table */}
>> +};
>> +MODULE_DEVICE_TABLE(of, cadence_qspi_of_match);
>> +#else
>> +#define cadence_qspi_of_match NULL
>> +#endif /* CONFIG_OF */
>> +
>> +static struct platform_driver cadence_qspi_platform_driver = {
>> +	.probe          = cadence_qspi_probe,
>> +	.remove         = cadence_qspi_remove,
>> +	.driver = {
>> +		.name   = CADENCE_QSPI_NAME,
>> +		.of_match_table = cadence_qspi_of_match,
>> +	},
>> +};
>> +
>> +module_platform_driver(cadence_qspi_platform_driver);
>> +
>> +MODULE_DESCRIPTION("Cadence QSPI Controller Driver");
>> +MODULE_LICENSE("GPL v2");
>> +MODULE_ALIAS("platform:" CADENCE_QSPI_NAME);
>> +MODULE_AUTHOR("Ley Foon Tan <[e-mail]>");
>> +MODULE_AUTHOR("Graham Moore <[e-mail]>");
>> +MODULE_AUTHOR("Vadivel Murugan R <[e-mail]>");
>> diff --git a/drivers/spi/spi-cadence-quadspi.h b/drivers/spi/spi-cadence-quadspi.h
>> new file mode 100644
>> index 000000000000..c78ee9423950
>> --- /dev/null
>> +++ b/drivers/spi/spi-cadence-quadspi.h
>> @@ -0,0 +1,272 @@
>> +/* SPDX-License-Identifier: BSD-2-Clause */
> NACK, should be GPLv2 and no need for boilerplate text below when SPDX
> Identifier is present.
sure, keep GPLv2
>> +/*
>> + * Driver for Cadence QSPI Controller
>> + *
>> + * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
>> + * Copyright Intel Corporation (C) 2019. All rights reserved.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms and conditions of the GNU General Public License,
>> + * version 2, as published by the Free Software Foundation.
>> + *
>> + * This program is distributed in the hope it will be useful, but WITHOUT
>> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
>> + * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
>> + * more details.
>> + *
>> + * You should have received a copy of the GNU General Public License along with
>> + * this program.  If not, see <http://www.gnu.org/licenses/>.
>> + */
>> +#ifndef __CADENCE_QSPI__H__
>> +#define __CADENCE_QSPI__H__
>> +#include <linux/reset.h>
>> +#include <linux/spi/spi-mem.h>
>> +
>> +#define CQSPI_MAX_CHIP_SELECT		(16)
>> +#define STIG_READ_MODE			1
>> +#define STIG_WRITE_MODE			2
>> +#define STIG_WRITE_READ_MODE		3
>> +#define IDC_READ_MODE			4
>> +#define IDC_WRITE_MODE			5
>> +
>> +#define QSPI_FLASH_TYPE_NOR		0
>> +#define QSPI_FLASH_TYPE_NAND		1
>> +
>
>> +#define QUAD_SIO			0
>> +#define QUAD_DIO			1
>> +#define QUAD_QIO			2
>> +
>> +#define QUAD_LSB			4
>> +
> Have driver specific prefixes please.
agreed!
>
>> +#define MACRONIX_4PP_CMD		0x38
>> +#define MACRONIX_WRSR_CMD		0x01
>> +
> These needs to be dropped
sure , drop it.
---
With Best Regards
Vadivel

Patch

diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig
index 6f7fdcbb9151..ef4d961feb54 100644
--- a/drivers/spi/Kconfig
+++ b/drivers/spi/Kconfig
@@ -192,6 +192,16 @@  config SPI_CADENCE
 	  This selects the Cadence SPI controller master driver
 	  used by Xilinx Zynq and ZynqMP.
 
+config SPI_CADENCE_QUADSPI
+	tristate "Cadence Quad SPI controller"
+	depends on OF && (ARM || ARM64 || COMPILE_TEST || X86)
+	depends on MTD || MTD_SPI_NOR || MTD_SPI_NAND
+	help
+	  Cadence QSPI is a specialized controller for connecting an SPI
+	  Flash over 1/2/4-bit wide bus. This enables support for the Quad SPI
+	  controller in master mode. This driver does not support generic SPI.
+	  The implementation only supports spi-mem interface.
+
 config SPI_CLPS711X
 	tristate "CLPS711X host SPI controller"
 	depends on ARCH_CLPS711X || COMPILE_TEST
diff --git a/drivers/spi/Makefile b/drivers/spi/Makefile
index bb49c9e6d0a0..84a59d75a13a 100644
--- a/drivers/spi/Makefile
+++ b/drivers/spi/Makefile
@@ -29,6 +29,7 @@  obj-$(CONFIG_SPI_BCM_QSPI)		+= spi-iproc-qspi.o spi-brcmstb-qspi.o spi-bcm-qspi.
 obj-$(CONFIG_SPI_BITBANG)		+= spi-bitbang.o
 obj-$(CONFIG_SPI_BUTTERFLY)		+= spi-butterfly.o
 obj-$(CONFIG_SPI_CADENCE)		+= spi-cadence.o
+obj-$(CONFIG_SPI_CADENCE_QUADSPI)		+= spi-cadence-quadspi.o
 obj-$(CONFIG_SPI_CLPS711X)		+= spi-clps711x.o
 obj-$(CONFIG_SPI_COLDFIRE_QSPI)		+= spi-coldfire-qspi.o
 obj-$(CONFIG_SPI_DAVINCI)		+= spi-davinci.o
diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
new file mode 100644
index 000000000000..bca391bfb58f
--- /dev/null
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -0,0 +1,1290 @@ 
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Driver for Cadence QSPI Controller
+ *
+ * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
+ * Copyright Intel Corporation (C) 2019. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/dmaengine.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/jiffies.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/spi/spi-mem.h>
+#include <linux/unaligned/be_byteshift.h>
+
+#include "spi-cadence-quadspi.h"
+
+/* Quirks */
+#define CQSPI_NEEDS_WR_DELAY		BIT(0)
+#define CQSPI_DISABLE_DAC_MODE		BIT(1)
+
+#define CADENCE_QSPI_NAME                       "cadence-qspi"
+
+struct cqspi_driver_platdata {
+	u32 hwcaps_mask;
+	u8 quirks;
+};
+
+unsigned int cadence_qspi_init_timeout(const unsigned long timeout_in_ms)
+{
+	return jiffies + msecs_to_jiffies(timeout_in_ms);
+}
+
+unsigned int cadence_qspi_check_timeout(const unsigned long timeout)
+{
+	return time_before(jiffies, timeout);
+}
+
+static irqreturn_t cadence_qspi_irq_handler(int this_irq, void *dev)
+{
+	struct struct_cqspi *cadence_qspi = dev;
+	u32 irq_status;
+
+	/* Read interrupt status */
+	irq_status = readl(cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
+	if (!irq_status)
+		return IRQ_HANDLED;
+
+	cadence_qspi->irq_status = irq_status;
+
+	/* Clear interrupt */
+	writel(irq_status, cadence_qspi->iobase + CQSPI_REG_IRQSTATUS);
+	if (irq_status)
+		complete(&cadence_qspi->transfer_complete);
+
+	return IRQ_HANDLED;
+}
+
+static u32 cadence_qspi_cmd2addr(const unsigned char *addr_buf, u32 addr_width)
+{
+	unsigned int addr = 0;
+	int i;
+
+	/* Invalid address return zero. */
+	if (addr_width > 4)
+		return 0;
+
+	for (i = 0; i < addr_width; i++) {
+		addr = addr << 8;
+		addr |= addr_buf[i];
+	}
+
+	return addr;
+}
+
+void enable_qspi_direct_access(void *reg_base, bool enable)
+{
+	u32 reg;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	if (enable)
+		reg |= CQSPI_REG_CONFIG_DIRECT_MASK;
+	else
+		reg &= ~CQSPI_REG_CONFIG_DIRECT_MASK;
+
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+void cadence_qspi_controller_enable(void *reg_base, bool enable)
+{
+	unsigned int reg;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	if (enable)
+		reg |= CQSPI_REG_CONFIG_ENABLE_MASK;
+	else
+		reg &= ~CQSPI_REG_CONFIG_ENABLE_MASK;
+
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static unsigned int cadence_qspi_wait_idle(void *reg_base)
+{
+	u32 timeout, count = 0;
+
+	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
+	while (cadence_qspi_check_timeout(timeout)) {
+		if (CQSPI_REG_IS_IDLE(reg_base)) {
+			count++;
+			if (count >= CQSPI_POLL_IDLE_RETRY)
+				return 1;
+		} else {
+			count = 0;
+		}
+	}
+
+	return 0;
+}
+
+static void cadence_qspi_readdata_capture(void *reg_base, u32 bypass, u32 delay)
+{
+	unsigned int reg;
+
+	cadence_qspi_controller_enable(reg_base, 0);
+
+	reg = readl(reg_base + CQSPI_REG_READCAPTURE);
+	if (bypass)
+		reg |= (1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
+	else
+		reg &= ~(1 << CQSPI_REG_READCAPTURE_BYPASS_LSB);
+
+	reg &= ~(CQSPI_REG_READCAPTURE_DELAY_MASK
+		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
+	reg |= ((delay & CQSPI_REG_READCAPTURE_DELAY_MASK)
+		<< CQSPI_REG_READCAPTURE_DELAY_LSB);
+	writel(reg, reg_base + CQSPI_REG_READCAPTURE);
+
+	cadence_qspi_controller_enable(reg_base, 1);
+}
+
+static void cadence_qspi_config_baudrate_div(void *reg_base, u32 ref_clk_hz,
+					     u32 sclk_hz)
+{
+	unsigned int reg, div;
+
+	/* Recalculate the baudrate divisor based on QSPI specification. */
+	div = DIV_ROUND_UP(ref_clk_hz, 2 * sclk_hz) - 1;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg &= ~(CQSPI_REG_CONFIG_BAUD_MASK << CQSPI_REG_CONFIG_BAUD_LSB);
+	div = (div & CQSPI_REG_CONFIG_BAUD_MASK) << CQSPI_REG_CONFIG_BAUD_LSB;
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+}
+
+static void cadence_qspi_cs(void *reg_base, u32 chip_select, u32 decoder_enable)
+{
+	unsigned int reg;
+
+	cadence_qspi_controller_enable(reg_base, 0);
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	/* docoder */
+	if (decoder_enable) {
+		reg |= CQSPI_REG_CONFIG_DECODE_MASK;
+	} else {
+		reg &= ~CQSPI_REG_CONFIG_DECODE_MASK;
+		chip_select = 0xF & ~(1 << chip_select);
+	}
+	reg &= ~(CQSPI_REG_CONFIG_CHIPSELECT_MASK
+			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB);
+	reg |= (chip_select & CQSPI_REG_CONFIG_CHIPSELECT_MASK)
+			<< CQSPI_REG_CONFIG_CHIPSELECT_LSB;
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+	cadence_qspi_controller_enable(reg_base, 1);
+}
+
+static int cadence_qspi_exec_flash_cmd(void *reg_base, unsigned int reg)
+{
+	unsigned int timeout;
+
+	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
+	reg |= CQSPI_REG_CMDCTRL_EXECUTE_MASK;
+	writel(reg, reg_base + CQSPI_REG_CMDCTRL);
+
+	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
+	while (cadence_qspi_check_timeout(timeout)) {
+		reg = readl(reg_base + CQSPI_REG_CMDCTRL) &
+			CQSPI_REG_CMDCTRL_INPROGRESS_MASK;
+		if (!reg)
+			break;
+	}
+
+	if (!cadence_qspi_wait_idle(reg_base) || reg != 0)
+		return -EIO;
+
+	return 0;
+}
+
+static int cqspi_command_read(void *reg_base, u32 txlen, const u_char *txbuf,
+			      u32 addrlen, const u8 *addrbuf, u32 rxlen,
+			      u8 *rxbuf, u32 flash_type)
+{
+	u32 addr_value, read_len, reg;
+	int ret;
+
+	if (!rxlen || rxlen > CQSPI_STIG_DATA_LEN_MAX || !rxbuf)
+		return -EINVAL;
+
+	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+	reg |= BIT(CQSPI_REG_CMDCTRL_RD_EN_LSB);
+
+	if (addrlen) {
+		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
+		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
+			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
+		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
+		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
+	}
+	/* 0 means 1 byte. */
+	reg |= (((rxlen - 1) & CQSPI_REG_CMDCTRL_RD_BYTES_MASK)
+		<< CQSPI_REG_CMDCTRL_RD_BYTES_LSB);
+	ret = cadence_qspi_exec_flash_cmd(reg_base, reg);
+	if (ret != 0)
+		return ret;
+
+	reg = readl(reg_base + CQSPI_REG_CMDREADDATALOWER);
+	read_len = (rxlen > 4) ? 4 : rxlen;
+	memcpy(rxbuf, &reg, read_len);
+	rxbuf += read_len;
+
+	if (rxlen > 4) {
+		reg = readl(reg_base + CQSPI_REG_CMDREADDATAUPPER);
+		read_len = rxlen - read_len;
+		memcpy(rxbuf, &reg, read_len);
+	}
+
+	return 0;
+}
+
+static int cqspi_command_write(void *reg_base, u32 txlen, const u8 *txbuf,
+			       u32 addrlen, const u8 *addrbuf, u32 datalen,
+			       const u8 *databuf, u32 flash_type)
+{
+	unsigned int addr_value, reg, data = 0;
+
+	if (!txlen || !txbuf)
+		return -EINVAL;
+
+	reg = txbuf[0] << CQSPI_REG_CMDCTRL_OPCODE_LSB;
+	if (datalen != 0) {
+		reg |= BIT(CQSPI_REG_CMDCTRL_WR_EN_LSB);
+		reg |= ((datalen - 1) & CQSPI_REG_CMDCTRL_WR_BYTES_MASK)
+			<< CQSPI_REG_CMDCTRL_WR_BYTES_LSB;
+		memcpy(&data, databuf, datalen);
+		writel(data, reg_base + CQSPI_REG_CMDWRITEDATALOWER);
+	}
+	if (addrlen) {
+		reg |= BIT(CQSPI_REG_CMDCTRL_ADDR_EN_LSB);
+		reg |= ((addrlen - 1) & CQSPI_REG_CMDCTRL_ADD_BYTES_MASK)
+			<< CQSPI_REG_CMDCTRL_ADD_BYTES_LSB;
+		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
+		writel(addr_value, reg_base + CQSPI_REG_CMDADDRESS);
+	}
+
+	return cadence_qspi_exec_flash_cmd(reg_base, reg);
+}
+
+static int cqspi_indirect_read_setup(void *reg_base, u32 txlen, const u8 *txbuf,
+				     u32 addrlen, const u8 *addrbuf,
+				     u32 dummy_bytes, u32 flash_type,
+				     u32 quad_mode)
+{
+	unsigned int addr_value, dummy_clk, reg;
+
+	if (addrlen) {
+		addr_value = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
+		writel(addr_value, reg_base + CQSPI_REG_INDIRECTRDSTARTADDR);
+	}
+
+	reg = txbuf[0] << CQSPI_REG_RD_INSTR_OPCODE_LSB;
+	reg |= (quad_mode & CQSPI_REG_RD_INSTR_TYPE_DATA_MASK) <<
+		CQSPI_REG_RD_INSTR_TYPE_DATA_LSB;
+
+	if (dummy_bytes) {
+		if (dummy_bytes > CQSPI_DUMMY_BYTES_MAX)
+			dummy_bytes = CQSPI_DUMMY_BYTES_MAX;
+		reg |= BIT(CQSPI_REG_RD_INSTR_MODE_EN_LSB);
+		writel(0xFF, reg_base + CQSPI_REG_MODE_BIT);
+		dummy_clk = dummy_bytes * CQSPI_DUMMY_CLKS_PER_BYTE;
+		dummy_clk -= CQSPI_DUMMY_CLKS_PER_BYTE;
+		if (dummy_clk)
+			reg |= (dummy_clk & CQSPI_REG_RD_INSTR_DUMMY_MASK)
+				<< CQSPI_REG_RD_INSTR_DUMMY_LSB;
+	} else if (flash_type == QSPI_FLASH_TYPE_NAND) {
+		reg |= ((1 * CQSPI_DUMMY_CLKS_PER_BYTE)
+				<< CQSPI_REG_RD_INSTR_DUMMY_LSB);
+	}
+	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
+	/* Set device size */
+	reg = readl(reg_base + CQSPI_REG_SIZE);
+	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
+	reg |= (addrlen - 1);
+	writel(reg, reg_base + CQSPI_REG_SIZE);
+	/* disable auto-polling */
+	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
+	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+
+	return 0;
+}
+
+static void cqspi_request_mmap_dma(struct struct_cqspi *cqspi)
+{
+	dma_cap_mask_t mask;
+
+	dma_cap_zero(mask);
+	dma_cap_set(DMA_MEMCPY, mask);
+
+	cqspi->rx_chan = dma_request_chan_by_mask(&mask);
+	if (IS_ERR(cqspi->rx_chan)) {
+		dev_err(&cqspi->pdev->dev, "No Rx DMA available\n");
+		cqspi->rx_chan = NULL;
+	}
+	init_completion(&cqspi->rx_dma_complete);
+}
+
+static void cqspi_rx_dma_callback(void *param)
+{
+	struct struct_cqspi *cqspi = param;
+
+	complete(&cqspi->rx_dma_complete);
+}
+
+static int cqspi_direct_read_execute(struct struct_cqspi *cqspi, u8 *buf,
+				     const u8 *addrbuf, size_t rxlen)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct device *dev = &pdev->dev;
+	enum dma_ctrl_flags flags = DMA_CTRL_ACK | DMA_PREP_INTERRUPT;
+	dma_addr_t dma_src = (dma_addr_t)cqspi->mmap_phys_base + addrbuf[0];
+	void __iomem *ahb_base = cqspi->qspi_ahb_virt;
+	int ret = 0;
+	struct dma_async_tx_descriptor *tx;
+	dma_cookie_t cookie;
+	dma_addr_t dma_dst;
+
+	if (!cqspi->rx_chan || !virt_addr_valid(buf)) {
+		memcpy_fromio(buf, ahb_base + addrbuf[0], rxlen);
+		return 0;
+	}
+
+	dma_dst = dma_map_single(dev, buf, rxlen, DMA_FROM_DEVICE);
+	if (dma_mapping_error(dev, dma_dst)) {
+		dev_err(dev, "dma mapping failed\n");
+		return -ENOMEM;
+	}
+	tx = dmaengine_prep_dma_memcpy(cqspi->rx_chan, dma_dst, dma_src,
+				       rxlen, flags);
+	if (!tx) {
+		dev_err(dev, "device_prep_dma_memcpy error\n");
+		ret = -EIO;
+		goto err_unmap;
+	}
+
+	tx->callback = cqspi_rx_dma_callback;
+	tx->callback_param = cqspi;
+	cookie = tx->tx_submit(tx);
+	reinit_completion(&cqspi->rx_dma_complete);
+
+	ret = dma_submit_error(cookie);
+	if (ret) {
+		dev_err(dev, "dma_submit_error %d\n", cookie);
+		ret = -EIO;
+		goto err_unmap;
+	}
+
+	dma_async_issue_pending(cqspi->rx_chan);
+	if (!wait_for_completion_timeout(&cqspi->rx_dma_complete,
+					 msecs_to_jiffies(rxlen))) {
+		dmaengine_terminate_sync(cqspi->rx_chan);
+		dev_err(dev, "DMA wait_for_completion_timeout\n");
+		ret = -ETIMEDOUT;
+		goto err_unmap;
+	}
+
+err_unmap:
+	dma_unmap_single(dev, dma_dst, rxlen, DMA_FROM_DEVICE);
+
+	return ret;
+}
+
+static int cqspi_indirect_read_execute(struct struct_cqspi *cqspi, u32 rxlen,
+				       u8 *rxbuf, u32 flash_type)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	void *reg_base = cqspi->iobase;
+	void *ahb_base = cqspi->qspi_ahb_virt;
+	u8 *rxbuf_end = rxbuf + rxlen;
+	u32 mod_bytes = rxlen % 4;
+	u32 bytes_to_read = 0;
+	int remaining = (int)rxlen;
+	u32 timeout, reg = 0;
+	int ret = 0;
+
+	writel(0, reg_base + CQSPI_REG_INDIRECTRDWATERMARK);
+	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
+	writel(remaining, reg_base + CQSPI_REG_INDIRECTRDBYTES);
+
+	mb();/* flush previous writes */
+
+	writel(pdata->fifo_depth - CQSPI_REG_SRAM_RESV_WORDS,
+	       reg_base + CQSPI_REG_SRAMPARTITION);
+	/* Clear all interrupts. */
+	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+	writel(CQSPI_IRQ_MASK_RD, reg_base + CQSPI_REG_IRQMASK);
+
+	reinit_completion(&cqspi->transfer_complete);
+	writel(CQSPI_REG_INDIRECTRD_START_MASK,
+	       reg_base + CQSPI_REG_INDIRECTRD);
+
+	while (remaining > 0) {
+		bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
+
+		while (bytes_to_read != 0) {
+			unsigned int word_remain = round_down(remaining, 4);
+
+			bytes_to_read *= CQSPI_FIFO_WIDTH;
+			bytes_to_read = bytes_to_read > remaining ?
+						remaining : bytes_to_read;
+			bytes_to_read = round_down(bytes_to_read, 4);
+			if (bytes_to_read) {
+				ioread32_rep(ahb_base, rxbuf,
+					     (bytes_to_read / 4));
+			} else if (!word_remain && mod_bytes) {
+				unsigned int temp = ioread32(ahb_base);
+
+				bytes_to_read = mod_bytes;
+				memcpy(rxbuf, &temp, min((unsigned int)
+				       (rxbuf_end - rxbuf), bytes_to_read));
+			}
+
+			rxbuf += bytes_to_read;
+			remaining -= bytes_to_read;
+			bytes_to_read = CQSPI_GET_RD_SRAM_LEVEL(reg_base);
+		}
+
+		if (remaining < 0)
+			reinit_completion(&cqspi->transfer_complete);
+	}
+
+	/* Check indirect done status */
+	timeout = cadence_qspi_init_timeout(CQSPI_READ_TIMEOUT_MS);
+	while (cadence_qspi_check_timeout(timeout)) {
+		reg = readl(reg_base + CQSPI_REG_INDIRECTRD);
+		if (reg & CQSPI_REG_INDIRECTRD_DONE_MASK)
+			break;
+	}
+	if (!(reg & CQSPI_REG_INDIRECTRD_DONE_MASK)) {
+		dev_err(&pdev->dev, "QSPI : Indirect read error %x\n", reg);
+		ret = -ETIMEDOUT;
+		goto failrd;
+	}
+	/* Disable interrupt */
+	writel(0, reg_base + CQSPI_REG_IRQMASK);
+	/* Clear indirect completion status */
+	writel(CQSPI_REG_INDIRECTRD_DONE_MASK, reg_base + CQSPI_REG_INDIRECTRD);
+
+	return 0;
+failrd:
+	/* Disable interrupt */
+	writel(0, reg_base + CQSPI_REG_IRQMASK);
+	/* Cancel the indirect read */
+	writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
+	       reg_base + CQSPI_REG_INDIRECTRD);
+	return ret;
+}
+
+static int cqspi_indirect_write_setup(void *reg_base, u32 txlen,
+				      const u8 *txbuf, u32 addrlen,
+				      const u8 *addrbuf, u32 flash_type,
+				      u32 quad_mode)
+{
+	unsigned int reg;
+
+	if (!txbuf)
+		return -EINVAL;
+
+	reg = readl(reg_base + CQSPI_REG_CONFIG);
+	reg &= ~(CQSPI_REG_CONFIG_DIRECT_MASK);
+	reg &= ~(CQSPI_REG_CONFIG_DMA_MASK);
+	writel(reg, reg_base + CQSPI_REG_CONFIG);
+
+	/* Set opcode. */
+	reg = txbuf[0] << CQSPI_REG_WR_INSTR_OPCODE_LSB;
+	reg |= BIT(CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS);
+	if (txbuf[0] == MACRONIX_4PP_CMD && flash_type == QSPI_FLASH_TYPE_NOR &&
+	    quad_mode == QUAD_QIO) {
+		/* Configure the quad */
+		reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK) <<
+		       CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB;
+	}
+	/* Configure the quad */
+	reg |= (quad_mode & CQSPI_REG_WR_INSTR_TYPE_DATA_MASK) <<
+	       CQSPI_REG_WR_INSTR_TYPE_DATA_LSB;
+	writel(reg, reg_base + CQSPI_REG_WR_INSTR);
+	/* Setup write address. */
+	reg = cadence_qspi_cmd2addr(&addrbuf[0], addrlen);
+	writel(reg, reg_base + CQSPI_REG_INDIRECTWRSTARTADDR);
+	reg = readl(reg_base + CQSPI_REG_SIZE);
+	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
+	reg |= ((addrlen - 1) & CQSPI_REG_SIZE_ADDRESS_MASK);
+	writel(reg, reg_base +  CQSPI_REG_SIZE);
+
+	/* disable auto-polling */
+	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	reg |= BIT(CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS);
+	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+
+	return 0;
+}
+
+static int cqspi_indirect_write_execute(struct struct_cqspi *cqspi, u32 txlen,
+					const u8 *txbuf, u32 flash_type)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	struct cqspi_flash_pdata *f_pdata =
+			&pdata->f_pdata[cqspi->current_cs];
+	void *reg_base = cqspi->iobase;
+	void *ahb_base = cqspi->qspi_ahb_virt;
+	u32 *irq_status = &cqspi->irq_status;
+	u32 page_size = f_pdata->page_size;
+	u32 write_bytes, timeout, reg = 0;
+	int remaining = (int)txlen;
+	int ret;
+
+	writel(0xa, reg_base + CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG);
+	writel(0x0, reg_base + CQSPI_REG_INDIRECTWRWATERMARK);
+	reg = readl(reg_base + CQSPI_REG_SIZE);
+	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
+	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
+	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
+	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
+	writel(reg, reg_base +  CQSPI_REG_SIZE);
+
+	writel(remaining, reg_base + CQSPI_REG_INDIRECTWRBYTES);
+	writel(CQSPI_REG_SRAM_PARTITION_WR, reg_base + CQSPI_REG_SRAMPARTITION);
+	/* Clear all interrupts. */
+	writel(CQSPI_IRQ_STATUS_MASK, reg_base + CQSPI_REG_IRQSTATUS);
+	writel(CQSPI_IRQ_MASK_WR, reg_base + CQSPI_REG_IRQMASK);
+	reinit_completion(&cqspi->transfer_complete);
+	writel(CQSPI_REG_INDIRECTWR_START_MASK,
+	       reg_base + CQSPI_REG_INDIRECTWR);
+
+	if (cqspi->wr_delay)
+		ndelay(cqspi->wr_delay);
+
+	while (remaining > 0) {
+		size_t write_words, mod_bytes;
+
+		write_bytes = remaining > page_size ? page_size : remaining;
+		write_words = write_bytes / 4;
+		mod_bytes = write_bytes % 4;
+
+		if (write_words) {
+			iowrite32_rep(ahb_base, txbuf, write_words);
+			txbuf += (write_words * 4);
+		}
+		if (mod_bytes) {
+			unsigned int temp = 0xFFFFFFFF;
+
+			memcpy(&temp, txbuf, mod_bytes);
+			iowrite32(temp, ahb_base);
+			txbuf += mod_bytes;
+		}
+		ret = wait_event_interruptible_timeout(cqspi->waitqueue,
+						       *irq_status &
+						       CQSPI_IRQ_MASK_WR,
+						       CQSPI_TIMEOUT_MS);
+		if (!(ret) & (*irq_status & CQSPI_IRQ_STATUS_ERR)) {
+			ret = -ETIMEDOUT;
+			goto failwr;
+		} else {
+			ret = 0;
+		}
+		remaining -= write_bytes;
+
+		if (remaining < 0)
+			reinit_completion(&cqspi->transfer_complete);
+	}
+
+	/* Check indirect done status */
+	timeout = cadence_qspi_init_timeout(CQSPI_TIMEOUT_MS);
+	while (cadence_qspi_check_timeout(timeout)) {
+		reg = readl(reg_base + CQSPI_REG_INDIRECTWR);
+		if (reg & CQSPI_REG_INDIRECTWR_DONE_MASK)
+			break;
+	}
+	if (!(reg & CQSPI_REG_INDIRECTWR_DONE_MASK)) {
+		dev_err(&pdev->dev, "QSPI: Indirect write error %x", reg);
+		ret = -ETIMEDOUT;
+		goto failwr;
+	}
+
+	return 0;
+
+failwr:
+	/* Disable interrupt. */
+	writel(0, reg_base + CQSPI_REG_IRQMASK);
+	/* Clear indirect completion status */
+	writel(CQSPI_REG_INDIRECTWR_DONE_MASK, reg_base + CQSPI_REG_INDIRECTWR);
+
+	/* Cancel the indirect write */
+	if (ret)
+		writel(CQSPI_REG_INDIRECTWR_CANCEL_MASK,
+		       reg_base + CQSPI_REG_INDIRECTWR);
+
+	return ret;
+}
+
+unsigned int cadence_qspi_is_controller_ready(void *reg_base)
+{
+	return cadence_qspi_wait_idle(reg_base);
+}
+
+void cadence_qspi_controller_init(struct struct_cqspi *cqspi)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+
+	cadence_qspi_controller_enable(cqspi->iobase, 0);
+
+	/* Configure the remap address register, no remap */
+	writel(0, cqspi->iobase + CQSPI_REG_REMAP);
+	/* Disable all interrupts. */
+	writel(0, cqspi->iobase + CQSPI_REG_IRQMASK);
+
+	/* DAC is disabled for Intel LGM SOC */
+	if (!cqspi->dac_mode) {
+		enable_qspi_direct_access(cqspi->iobase, 0);
+	} else {
+		enable_qspi_direct_access(cqspi->iobase, 1);
+		/* TODO: for TI platform to be enabled */
+		cqspi_request_mmap_dma(cqspi);
+	}
+
+	/* Load indirect trigger address. */
+	writel(pdata->trigger_address,
+	       cqspi->iobase + CQSPI_REG_INDIRECTTRIGGER);
+
+	cadence_qspi_controller_enable(cqspi->iobase, 1);
+}
+
+unsigned int calculate_ticks_for_ns(u32 ref_clk_hz, u32 ns_val)
+{
+	unsigned int ticks;
+
+	ticks = ref_clk_hz / 1000;      /* kHz */
+	ticks = DIV_ROUND_UP(ticks * ns_val, 1000000);
+
+	return ticks;
+}
+
+void cadence_qspi_delay(struct struct_cqspi *cqspi, u32 ref_clk, u32 sclk_hz)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cqspi->current_cs];
+	void __iomem *iobase = cqspi->iobase;
+	const unsigned int ref_clk_hz = pdata->master_ref_clk_hz;
+	unsigned int tshsl, tchsh, tslch, tsd2d;
+	unsigned int reg;
+	unsigned int tsclk;
+
+	cadence_qspi_controller_enable(cqspi->iobase, 0);
+	/* calculate the number of ref ticks for one sclk tick */
+	tsclk = DIV_ROUND_UP(ref_clk_hz, sclk_hz);
+
+	/* this particular value must be at least one sclk */
+	if (tshsl < tsclk)
+		tshsl = tsclk;
+
+	tchsh = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tchsh_ns);
+	tslch = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tslch_ns);
+	tsd2d = calculate_ticks_for_ns(ref_clk_hz, f_pdata->tsd2d_ns);
+
+	reg = ((tshsl & CQSPI_REG_DELAY_TSHSL_MASK)
+			<< CQSPI_REG_DELAY_TSHSL_LSB);
+	reg |= ((tchsh & CQSPI_REG_DELAY_TCHSH_MASK)
+			<< CQSPI_REG_DELAY_TCHSH_LSB);
+	reg |= ((tslch & CQSPI_REG_DELAY_TSLCH_MASK)
+			<< CQSPI_REG_DELAY_TSLCH_LSB);
+	reg |= ((tsd2d & CQSPI_REG_DELAY_TSD2D_MASK)
+			<< CQSPI_REG_DELAY_TSD2D_LSB);
+	writel(reg, iobase + CQSPI_REG_DELAY);
+	cadence_qspi_controller_enable(cqspi->iobase, 1);
+}
+
+void cadence_qspi_switch_chipselect(struct struct_cqspi *cqspi, u32 cs)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	struct cqspi_flash_pdata *f_pdata = &pdata->f_pdata[cs];
+	void __iomem *iobase = cqspi->iobase;
+	unsigned int reg;
+
+	cadence_qspi_controller_enable(cqspi->iobase, 0);
+	/* Configure page size and block size. */
+	reg = readl(iobase + CQSPI_REG_SIZE);
+	/* clear the previous value */
+	reg &= ~(CQSPI_REG_SIZE_PAGE_MASK << CQSPI_REG_SIZE_PAGE_LSB);
+	reg &= ~(CQSPI_REG_SIZE_BLOCK_MASK << CQSPI_REG_SIZE_BLOCK_LSB);
+	reg |= (f_pdata->page_size << CQSPI_REG_SIZE_PAGE_LSB);
+	reg |= (f_pdata->block_size << CQSPI_REG_SIZE_BLOCK_LSB);
+	writel(reg, iobase + CQSPI_REG_SIZE);
+	/* configure the chip select */
+	cadence_qspi_cs(iobase, cs, pdata->ext_decoder);
+	cadence_qspi_controller_enable(cqspi->iobase, 1);
+}
+
+static int cadence_qspi_mem_process(struct struct_cqspi *cqspi,
+				    struct spi_mem *mem,
+				    const struct spi_mem_op *op)
+{
+	struct platform_device *pdev = cqspi->pdev;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	unsigned int tmpbufsize, n_trans = 0, totalxferlen = 0;
+	void __iomem *iobase = cqspi->iobase;
+	struct spi_mem_op_cadence ops[4] = { };
+	struct spi_mem_op_cadence *cmd_ops = NULL;
+	struct spi_mem_op_cadence *data_ops = NULL;
+	struct spi_mem_op_cadence *dummy_ops = NULL;
+	struct spi_mem_op_cadence *addr_ops = NULL;
+	struct cqspi_flash_pdata *f_pdata;
+	int rdid_length, mode, ret, i;
+	u8 *tmpbuf;
+	u32 sclk;
+
+	if (cqspi->current_cs != mem->spi->chip_select) {
+		cqspi->current_cs = mem->spi->chip_select;
+		cadence_qspi_switch_chipselect(cqspi, mem->spi->chip_select);
+	}
+
+	f_pdata = &pdata->f_pdata[cqspi->current_cs];
+	if (f_pdata->flash_type == QSPI_FLASH_TYPE_NOR)
+		rdid_length = 6;
+	else
+		rdid_length = 3;
+
+	tmpbufsize = sizeof(op->cmd.opcode) + op->addr.nbytes +
+			op->dummy.nbytes;
+
+	tmpbuf = kzalloc(tmpbufsize, GFP_KERNEL | GFP_DMA);
+	if (!tmpbuf)
+		return -ENOMEM;
+
+	tmpbuf[0] = op->cmd.opcode;
+	ops[n_trans].tx_buf = tmpbuf;
+	ops[n_trans].len = sizeof(op->cmd.opcode);
+	ops[n_trans].tx_nbits = op->cmd.buswidth;
+
+	n_trans++;
+	totalxferlen++;
+
+	if (op->addr.nbytes) {
+		int i;
+
+		for (i = 0; i < op->addr.nbytes; i++)
+			tmpbuf[i + 1] = op->addr.val >>
+					(8 * (op->addr.nbytes - i - 1));
+
+		ops[n_trans].tx_buf = tmpbuf + 1;
+		ops[n_trans].len = op->addr.nbytes;
+		ops[n_trans].tx_nbits = op->addr.buswidth;
+
+		n_trans++;
+		totalxferlen += op->addr.nbytes;
+	}
+	if (op->dummy.nbytes) {
+		memset(tmpbuf + op->addr.nbytes + 1, 0xff, op->dummy.nbytes);
+		ops[n_trans].tx_buf = tmpbuf + op->addr.nbytes + 1;
+		ops[n_trans].len = op->dummy.nbytes;
+		ops[n_trans].tx_nbits = op->dummy.buswidth;
+
+		n_trans++;
+		totalxferlen += op->dummy.nbytes;
+	}
+	if (op->data.nbytes) {
+		if (op->data.dir == SPI_MEM_DATA_IN) {
+			ops[n_trans].rx_buf = op->data.buf.in;
+			ops[n_trans].rx_nbits = op->data.buswidth;
+		} else {
+			ops[n_trans].tx_buf = op->data.buf.out;
+			ops[n_trans].tx_nbits = op->data.buswidth;
+		}
+
+		ops[n_trans].len = op->data.nbytes;
+		n_trans++;
+		totalxferlen += op->data.nbytes;
+	}
+
+	for (i = 0; i < n_trans; i++)
+		dev_dbg(&pdev->dev, "ops[%d] %d\n", i, ops[i].len);
+
+	switch (n_trans) {
+	case 1:
+		cmd_ops = &ops[0];
+		break;
+	case 2:
+		cmd_ops = &ops[0];
+		if (f_pdata->flash_type == QSPI_FLASH_TYPE_NAND) {
+			if (data_ops->rx_buf)
+				data_ops = &ops[1];
+			else
+				addr_ops = &ops[1];
+		} else {
+			data_ops = &ops[1];
+		}
+		break;
+	case 3:
+		cmd_ops = &ops[0];
+		addr_ops = &ops[1];
+		data_ops = &ops[2];
+		break;
+	case 4:
+		cmd_ops = &ops[0];
+		addr_ops = &ops[1];
+		dummy_ops = &ops[2];
+		data_ops = &ops[3];
+		break;
+	default:
+		dev_err(&pdev->dev, "Unsupported n_trans %u\n", n_trans);
+		return -EINVAL;
+	}
+
+	if (!data_ops)
+		mode = STIG_WRITE_MODE;
+	else if (data_ops->len > rdid_length)
+		mode = data_ops->tx_buf ? IDC_WRITE_MODE : IDC_READ_MODE;
+	else
+		mode = data_ops->tx_buf ? STIG_WRITE_MODE : STIG_READ_MODE;
+
+	sclk = mem->spi->max_speed_hz;
+	cadence_qspi_controller_enable(iobase, 0);
+	cadence_qspi_config_baudrate_div(iobase, pdata->master_ref_clk_hz,
+					 sclk);
+	cadence_qspi_delay(cqspi, pdata->master_ref_clk_hz, sclk);
+	cadence_qspi_readdata_capture(iobase, 1, f_pdata->read_delay);
+	cadence_qspi_controller_enable(iobase, 1);
+
+	/* execute transfer */
+	switch (mode) {
+	case STIG_WRITE_MODE:
+		ret = cqspi_command_write(iobase, cmd_ops->len, cmd_ops->tx_buf,
+					  addr_ops ? addr_ops->len : 0,
+					  addr_ops ? addr_ops->tx_buf : NULL,
+					  data_ops ? data_ops->len : 0,
+					  data_ops ? data_ops->tx_buf : NULL,
+					  f_pdata->flash_type);
+		break;
+	case STIG_READ_MODE:
+		ret = cqspi_command_read(iobase, cmd_ops->len, cmd_ops->tx_buf,
+					 addr_ops ? addr_ops->len : 0,
+					 addr_ops ? addr_ops->tx_buf : NULL,
+					 data_ops ? data_ops->len : 0,
+					 data_ops ? data_ops->rx_buf : NULL,
+					 f_pdata->flash_type);
+		break;
+	case IDC_WRITE_MODE:
+		ret = cqspi_indirect_write_setup(iobase, cmd_ops->len,
+						 cmd_ops->tx_buf,
+						 addr_ops ? addr_ops->len : 0,
+						 addr_ops ? addr_ops->tx_buf : 0,
+						 f_pdata->flash_type,
+						 f_pdata->quad);
+		ret = cqspi_indirect_write_execute(cqspi, data_ops->len,
+						   data_ops->tx_buf,
+						   f_pdata->flash_type);
+		break;
+	case IDC_READ_MODE:
+		ret = cqspi_indirect_read_setup(iobase, cmd_ops->len,
+						cmd_ops->tx_buf,
+						addr_ops ? addr_ops->len : 0,
+						addr_ops ? addr_ops->tx_buf : 0,
+						dummy_ops ? dummy_ops->len : 0,
+						f_pdata->flash_type,
+						f_pdata->quad);
+		ret = cqspi_indirect_read_execute(cqspi, data_ops->len,
+						  data_ops->rx_buf,
+						  f_pdata->flash_type);
+		/* TODO: for TI DMA + DAC to be enabled */
+		break;
+	default:
+		dev_err(&pdev->dev, "Unsupported mode %u\n", mode);
+		return -EINVAL;
+	}
+
+	return ret;
+}
+
+int cadence_qspi_exec_mem_op(struct spi_mem *mem, const struct spi_mem_op *op)
+{
+	struct struct_cqspi *cqspi = spi_master_get_devdata(mem->spi->master);
+	int ret;
+
+	mutex_lock(&cqspi->lock);
+	ret = cadence_qspi_mem_process(cqspi, mem, op);
+	if (ret)
+		dev_err(&mem->spi->dev, "Error: qspi transfer failed!!!.\n");
+	mutex_unlock(&cqspi->lock);
+
+	return ret;
+}
+
+static const struct spi_controller_mem_ops cadence_qspi_mem_ops = {
+	.exec_op = cadence_qspi_exec_mem_op,
+};
+
+static int cadence_qspi_setup(struct spi_device *spi)
+{
+	if (spi->chip_select > spi->master->num_chipselect) {
+		dev_err(&spi->dev, "%d CS is out of range\n", spi->chip_select);
+		return -EINVAL;
+	}
+	return 0;
+}
+
+static int cadence_qspi_of_get_pdata(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct device_node *nc;
+	struct cqspi_platform_data *pdata = pdev->dev.platform_data;
+	struct cqspi_flash_pdata *f_pdata;
+	unsigned int cs;
+	unsigned int prop;
+
+	pdata->is_decoded_cs = of_property_read_bool(np, "cdns,is-decoded-cs");
+
+	if (of_property_read_u32(np, "cdns,trigger-address", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine trigger-address\n");
+		return -ENXIO;
+	}
+	pdata->trigger_address = prop;
+
+	pdata->rclk_en = of_property_read_bool(np, "cdns,rclk-en");
+
+	if (of_property_read_u32(np, "cdns,qspi-phyaddr", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine cdns,qspi-phyaddr\n");
+		return -ENXIO;
+	}
+	pdata->qspi_ahb_phy = prop;
+
+	if (of_property_read_u32(np, "cdns,qspi-physize", &prop)) {
+		dev_info(&pdev->dev, "missing cdns,qspi-physize to 128 kB\n");
+		prop = 128;
+	}
+	pdata->qspi_ahb_size = prop * 1024;
+
+	if (of_property_read_u32(np, "cdns,qspi-phymask", &prop))
+		prop = CQSPI_INDIRECTTRIGGER_ADDR_MASK;
+	pdata->qspi_ahb_mask = prop;
+
+	if (of_property_read_u32(np, "bus-num", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine bus-num\n");
+		return -ENXIO;
+	}
+	pdata->bus_num = prop;
+
+	if (of_property_read_u32(np, "num-chipselect", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine num-chipselect\n");
+		return -ENXIO;
+	}
+	pdata->num_chipselect = prop;
+
+	if (of_property_read_u32(np, "cdns,fifo-depth", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine fifo-depth\n");
+		return -ENXIO;
+	}
+	pdata->fifo_depth = prop;
+
+	if (of_property_read_u32(np, "ext-decoder", &prop)) {
+		dev_err(&pdev->dev, "couldn't determine ext-decoder\n");
+		return -ENXIO;
+	}
+	pdata->ext_decoder = prop;
+
+	pdata->enable_dma = of_property_read_bool(np, "dmas");
+	dev_info(&pdev->dev, "DMA %senabled\n", pdata->enable_dma ? "" : "NOT");
+
+	/* Get flash devices platform data */
+	for_each_child_of_node(np, nc) {
+		if (!of_device_is_available(nc))
+			continue;
+
+		if (of_property_read_u32(nc, "reg", &cs)) {
+			dev_err(&pdev->dev, "couldn't determine reg\n");
+			return -ENXIO;
+		}
+		f_pdata = &pdata->f_pdata[cs];
+
+		/* use compatible string to determine flash type */
+		if (of_device_is_compatible(nc, "spinand"))
+			f_pdata->flash_type = QSPI_FLASH_TYPE_NAND;
+		else
+			f_pdata->flash_type = QSPI_FLASH_TYPE_NOR;
+
+		if (of_property_read_u32(nc, "spi-rx-bus-width", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine quad\n");
+			return -ENXIO;
+		}
+		f_pdata->quad = (prop == 4) ? QUAD_QIO : QUAD_SIO;
+
+		if (of_property_read_u32(nc, "page-size", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine page-size\n");
+			return -ENXIO;
+		}
+		f_pdata->page_size = prop;
+
+		if (of_property_read_u32(nc, "block-size", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine block-size\n");
+			return -ENXIO;
+		}
+		f_pdata->block_size = prop;
+
+		if (of_property_read_u32(nc, "cdns,read-delay", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine read-delay\n");
+			return -ENXIO;
+		}
+		f_pdata->read_delay = prop;
+
+		if (of_property_read_u32(nc, "cdns,tshsl-ns", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine tshsl-ns\n");
+			return -ENXIO;
+		}
+		f_pdata->tshsl_ns = prop;
+
+		if (of_property_read_u32(nc, "cdns,tsd2d-ns", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine tsd2d-ns\n");
+			return -ENXIO;
+		}
+		f_pdata->tsd2d_ns = prop;
+
+		if (of_property_read_u32(nc, "cdns,tchsh-ns", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine tchsh-ns\n");
+			return -ENXIO;
+		}
+		f_pdata->tchsh_ns = prop;
+
+		if (of_property_read_u32(nc, "cdns,tslch-ns", &prop)) {
+			dev_err(&pdev->dev, "couldn't determine tslch-ns\n");
+			return -ENXIO;
+		}
+		f_pdata->tslch_ns = prop;
+	}
+	return 0;
+}
+
+static int cadence_qspi_probe(struct platform_device *pdev)
+{
+	struct cqspi_platform_data *pdata;
+	struct device *dev = &pdev->dev;
+	struct struct_cqspi *cqspi;
+	struct spi_master *master;
+	struct reset_control *rstc, *rstc_ocp;
+	const struct cqspi_driver_platdata *ddata;
+	struct resource *res = NULL;
+	int ret;
+
+	master = spi_alloc_master(&pdev->dev, sizeof(*cqspi));
+	if (!master) {
+		dev_err(&pdev->dev, "spi_alloc_master failed\n");
+		return -ENOMEM;
+	}
+	master->mode_bits = SPI_CS_HIGH | SPI_CPOL | SPI_CPHA | SPI_TX_QUAD |
+				SPI_RX_QUAD | SPI_TX_DUAL | SPI_RX_DUAL;
+	master->setup = cadence_qspi_setup;
+	master->mem_ops = &cadence_qspi_mem_ops;
+	master->dev.of_node = pdev->dev.of_node;
+	cqspi = spi_master_get_devdata(master);
+	cqspi->pdev = pdev;
+
+	pdata = kmalloc(sizeof(*pdata), GFP_KERNEL);
+	if (!pdata) {
+		ret = -ENOMEM;
+		goto err_pdata;
+	}
+	pdev->dev.platform_data = pdata;
+
+	cqspi->clk = devm_clk_get(&pdev->dev, "qspi");
+	if (IS_ERR(cqspi->clk)) {
+		dev_err(&pdev->dev, "cannot get qspi clk\n");
+		return PTR_ERR(cqspi->clk);
+	}
+	pdata->master_ref_clk_hz = clk_get_rate(cqspi->clk);
+
+	ret = clk_prepare_enable(cqspi->clk);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "failed to enable qspi clock: %d\n", ret);
+		return ret;
+	}
+
+	ret = cadence_qspi_of_get_pdata(pdev);
+	if (ret) {
+		dev_err(&pdev->dev, "Get platform data failed.\n");
+		return -ENODEV;
+	}
+
+	cqspi->res = res;
+	/* Obtain and remap controller address. */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	cqspi->iobase = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(cqspi->iobase)) {
+		dev_err(dev, "Cannot remap controller address.\n");
+		return PTR_ERR(cqspi->iobase);
+	}
+
+	/* Obtain and remap AHB address. */
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
+	cqspi->qspi_ahb_virt = devm_ioremap_resource(dev, res);
+	if (IS_ERR(cqspi->qspi_ahb_virt)) {
+		dev_err(dev, "Cannot remap AHB address.\n");
+		return PTR_ERR(cqspi->qspi_ahb_virt);
+	}
+	cqspi->mmap_phys_base = (dma_addr_t)res->start;
+	cqspi->ahb_size = resource_size(res);
+
+	/* Obtain QSPI reset control */
+	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
+	if (IS_ERR(rstc)) {
+		dev_err(dev, "Cannot get QSPI reset.\n");
+		return PTR_ERR(rstc);
+	}
+
+	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
+	if (IS_ERR(rstc_ocp)) {
+		dev_err(dev, "Cannot get QSPI OCP reset.\n");
+		return PTR_ERR(rstc_ocp);
+	}
+
+	reset_control_assert(rstc);
+	reset_control_deassert(rstc);
+
+	reset_control_assert(rstc_ocp);
+	reset_control_deassert(rstc_ocp);
+
+	ddata  = of_device_get_match_data(dev);
+	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))
+		cqspi->wr_delay = 5 * DIV_ROUND_UP(NSEC_PER_SEC,
+						   pdata->master_ref_clk_hz);
+
+	init_completion(&cqspi->transfer_complete);
+
+	cqspi->irq = platform_get_irq(pdev, 0);
+	if (cqspi->irq < 0) {
+		dev_err(dev, "platform_get_irq failed.\n");
+		ret = -ENXIO;
+		goto err_irq;
+	}
+	ret = devm_request_irq(dev, cqspi->irq, cadence_qspi_irq_handler, 0,
+			       pdev->name, cqspi);
+	if (ret) {
+		dev_err(dev, "request_irq failed.\n");
+		goto err_irq;
+	}
+
+	master->bus_num = pdata->bus_num;
+	master->num_chipselect = pdata->num_chipselect;
+	mutex_init(&cqspi->lock);
+	platform_set_drvdata(pdev, master);
+	cadence_qspi_controller_init(cqspi);
+	cqspi->current_cs = 0;
+
+	ret = devm_spi_register_master(dev, master);
+	if (ret) {
+		dev_err(&pdev->dev, "devm_spi_register_master failed.\n");
+		goto err_of;
+	}
+
+	if (ddata && (ddata->quirks & CQSPI_DISABLE_DAC_MODE))
+		cqspi->dac_mode = false;
+
+	return 0;
+
+err_pdata:
+	kfree(pdata);
+err_irq:
+	free_irq(cqspi->irq, cqspi);
+err_of:
+	spi_master_put(master);
+	dev_err(&pdev->dev, "Cadence QSPI controller probe failed\n");
+	return ret;
+}
+
+static int cadence_qspi_remove(struct platform_device *pdev)
+{
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct struct_cqspi *cadence_qspi = spi_master_get_devdata(master);
+
+	cadence_qspi_controller_enable(cadence_qspi->iobase, 0);
+	platform_set_drvdata(pdev, NULL);
+	free_irq(cadence_qspi->irq, cadence_qspi);
+	iounmap(cadence_qspi->iobase);
+	iounmap(cadence_qspi->qspi_ahb_virt);
+	release_mem_region(cadence_qspi->res->start,
+			   resource_size(cadence_qspi->res));
+	kfree(pdev->dev.platform_data);
+	spi_unregister_master(master);
+	spi_master_put(master);
+	return 0;
+}
+
+static const struct cqspi_driver_platdata k2g_qspi = {
+	.quirks = CQSPI_NEEDS_WR_DELAY,
+};
+
+static const struct cqspi_driver_platdata am654_ospi = {
+	.quirks = CQSPI_NEEDS_WR_DELAY,
+};
+
+static const struct cqspi_driver_platdata intel_lgm_qspi = {
+	.quirks = CQSPI_DISABLE_DAC_MODE,
+};
+
+#ifdef CONFIG_OF
+static const struct of_device_id cadence_qspi_of_match[] = {
+	{
+		.compatible = "cadence,qspi",
+	},
+	{
+		.compatible = "ti,k2g-qspi",
+		.data = &k2g_qspi,
+	},
+	{
+		.compatible = "ti,am654-ospi",
+		.data = &am654_ospi,
+	},
+	{
+		.compatible = "intel,lgm-qspi",
+		.data = &intel_lgm_qspi,
+	},
+	{ /* end of table */}
+};
+MODULE_DEVICE_TABLE(of, cadence_qspi_of_match);
+#else
+#define cadence_qspi_of_match NULL
+#endif /* CONFIG_OF */
+
+static struct platform_driver cadence_qspi_platform_driver = {
+	.probe          = cadence_qspi_probe,
+	.remove         = cadence_qspi_remove,
+	.driver = {
+		.name   = CADENCE_QSPI_NAME,
+		.of_match_table = cadence_qspi_of_match,
+	},
+};
+
+module_platform_driver(cadence_qspi_platform_driver);
+
+MODULE_DESCRIPTION("Cadence QSPI Controller Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:" CADENCE_QSPI_NAME);
+MODULE_AUTHOR("Ley Foon Tan <[e-mail]>");
+MODULE_AUTHOR("Graham Moore <[e-mail]>");
+MODULE_AUTHOR("Vadivel Murugan R <[e-mail]>");
diff --git a/drivers/spi/spi-cadence-quadspi.h b/drivers/spi/spi-cadence-quadspi.h
new file mode 100644
index 000000000000..c78ee9423950
--- /dev/null
+++ b/drivers/spi/spi-cadence-quadspi.h
@@ -0,0 +1,272 @@ 
+/* SPDX-License-Identifier: BSD-2-Clause */
+/*
+ * Driver for Cadence QSPI Controller
+ *
+ * Copyright Altera Corporation (C) 2012-2014. All rights reserved.
+ * Copyright Intel Corporation (C) 2019. All rights reserved.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along with
+ * this program.  If not, see <http://www.gnu.org/licenses/>.
+ */
+#ifndef __CADENCE_QSPI__H__
+#define __CADENCE_QSPI__H__
+#include <linux/reset.h>
+#include <linux/spi/spi-mem.h>
+
+#define CQSPI_MAX_CHIP_SELECT		(16)
+#define STIG_READ_MODE			1
+#define STIG_WRITE_MODE			2
+#define STIG_WRITE_READ_MODE		3
+#define IDC_READ_MODE			4
+#define IDC_WRITE_MODE			5
+
+#define QSPI_FLASH_TYPE_NOR		0
+#define QSPI_FLASH_TYPE_NAND		1
+
+#define QUAD_SIO			0
+#define QUAD_DIO			1
+#define QUAD_QIO			2
+
+#define QUAD_LSB			4
+
+#define MACRONIX_4PP_CMD		0x38
+#define MACRONIX_WRSR_CMD		0x01
+
+/* Operation timeout value */
+#define CQSPI_TIMEOUT_MS			5000
+#define CQSPI_READ_TIMEOUT_MS			10
+#define CQSPI_POLL_IDLE_RETRY			3
+#define CQSPI_FIFO_WIDTH			4
+
+/* Controller sram size in word */
+#define CQSPI_REG_SRAM_RESV_WORDS		2
+#define CQSPI_REG_SRAM_PARTITION_WR		1
+#define CQSPI_REG_SRAM_THRESHOLD_BYTES		50
+
+/* Instruction type */
+#define CQSPI_INST_TYPE_SINGLE			0
+#define CQSPI_INST_TYPE_DUAL			1
+#define CQSPI_INST_TYPE_QUAD			2
+#define CQSPI_DUMMY_CLKS_PER_BYTE		8
+#define CQSPI_DUMMY_BYTES_MAX			4
+#define CQSPI_STIG_DATA_LEN_MAX			8
+#define CQSPI_INDIRECTTRIGGER_ADDR_MASK		0xFFFFF
+
+/* Register map */
+#define	CQSPI_REG_CONFIG			0x00
+#define	CQSPI_REG_CONFIG_ENABLE_MASK		BIT(0)
+#define	CQSPI_REG_CONFIG_DIRECT_MASK		BIT(7)
+#define	CQSPI_REG_CONFIG_DECODE_MASK		BIT(9)
+#define	CQSPI_REG_CONFIG_CHIPSELECT_LSB		10
+#define CQSPI_REG_CONFIG_DMA_MASK		BIT(15)
+#define	CQSPI_REG_CONFIG_BAUD_LSB		19
+#define	CQSPI_REG_CONFIG_IDLE_LSB		31
+#define	CQSPI_REG_CONFIG_CHIPSELECT_MASK	0xF
+#define	CQSPI_REG_CONFIG_BAUD_MASK		0xF
+#define	CQSPI_REG_RD_INSTR			0x04
+#define	CQSPI_REG_RD_INSTR_OPCODE_LSB		0
+#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_LSB	8
+#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_LSB	12
+#define	CQSPI_REG_RD_INSTR_TYPE_DATA_LSB	16
+#define	CQSPI_REG_RD_INSTR_MODE_EN_LSB		20
+#define	CQSPI_REG_RD_INSTR_DUMMY_LSB		24
+#define	CQSPI_REG_RD_INSTR_TYPE_INSTR_MASK	0x3
+#define	CQSPI_REG_RD_INSTR_TYPE_ADDR_MASK	0x3
+#define	CQSPI_REG_RD_INSTR_TYPE_DATA_MASK	0x3
+#define	CQSPI_REG_RD_INSTR_DUMMY_MASK		0x1F
+#define	CQSPI_REG_WR_INSTR			0x08
+#define	CQSPI_REG_WR_INSTR_OPCODE_LSB		0
+#define	CQSPI_REG_WR_INSTR_TYPE_DATA_MASK	0x3
+#define	CQSPI_REG_WR_INSTR_TYPE_DATA_LSB	16
+#define	CQSPI_REG_WR_INSTR_TYPE_ADDR_MASK	0x3
+#define	CQSPI_REG_WR_INSTR_TYPE_ADDR_LSB	12
+
+/*! Field WEL_DIS_FLD - wel_dis_fld */
+#define CQSPI_REG_WR_CONFIG_WEL_DIS_FLD_POS	8
+#define CQSPI_REG_WR_COMPLETION_CTRL		0x38
+#define CQSPI_REG_WR_COMPLETION_DIS_POLLING_FLD_POS	14
+
+#define	CQSPI_REG_DELAY				0x0C
+#define	CQSPI_REG_DELAY_TSLCH_LSB		0
+#define	CQSPI_REG_DELAY_TCHSH_LSB		8
+#define	CQSPI_REG_DELAY_TSD2D_LSB		16
+#define	CQSPI_REG_DELAY_TSHSL_LSB		24
+#define	CQSPI_REG_DELAY_TSLCH_MASK		0xFF
+#define	CQSPI_REG_DELAY_TCHSH_MASK		0xFF
+#define	CQSPI_REG_DELAY_TSD2D_MASK		0xFF
+#define	CQSPI_REG_DELAY_TSHSL_MASK		0xFF
+#define	CQSPI_REG_READCAPTURE			0x10
+#define	CQSPI_REG_READCAPTURE_BYPASS_LSB	0
+#define	CQSPI_REG_READCAPTURE_DELAY_LSB		1
+#define	CQSPI_REG_READCAPTURE_DELAY_MASK	0xF
+#define	CQSPI_REG_SIZE				0x14
+#define	CQSPI_REG_SIZE_ADDRESS_LSB		0
+#define	CQSPI_REG_SIZE_PAGE_LSB			4
+#define	CQSPI_REG_SIZE_BLOCK_LSB		16
+#define	CQSPI_REG_SIZE_ADDRESS_MASK		0xF
+#define	CQSPI_REG_SIZE_PAGE_MASK		0xFFF
+#define	CQSPI_REG_SIZE_BLOCK_MASK		0x3F
+#define	CQSPI_REG_SRAMPARTITION			0x18
+#define	CQSPI_REG_INDIRECTTRIGGER		0x1C
+#define	CQSPI_REG_DMA				0x20
+#define	CQSPI_REG_DMA_SINGLE_LSB		0
+#define	CQSPI_REG_DMA_BURST_LSB			8
+#define	CQSPI_REG_DMA_SINGLE_MASK		0xFF
+#define	CQSPI_REG_DMA_BURST_MASK		0xFF
+#define	CQSPI_REG_REMAP				0x24
+#define	CQSPI_REG_MODE_BIT			0x28
+#define	CQSPI_REG_SDRAMLEVEL			0x2C
+#define	CQSPI_REG_SDRAMLEVEL_RD_LSB		0
+#define	CQSPI_REG_SDRAMLEVEL_WR_LSB		16
+#define	CQSPI_REG_SDRAMLEVEL_RD_MASK		0xFFFF
+#define	CQSPI_REG_SDRAMLEVEL_WR_MASK		0xFFFF
+
+#define	CQSPI_REG_IRQSTATUS			0x40
+#define	CQSPI_REG_IRQMASK			0x44
+#define	CQSPI_REG_INDIRECTRD			0x60
+#define	CQSPI_REG_INDIRECTRD_START_MASK		BIT(0)
+#define	CQSPI_REG_INDIRECTRD_CANCEL_MASK	BIT(1)
+#define	CQSPI_REG_INDIRECTRD_DONE_MASK		BIT(5)
+#define	CQSPI_REG_INDIRECTRDWATERMARK		0x64
+#define	CQSPI_REG_INDIRECTRDSTARTADDR		0x68
+#define	CQSPI_REG_INDIRECTRDBYTES		0x6C
+#define CQSPI_INDIRECT_TRIGGER_ADDR_RANGE_REG	0x80
+#define	CQSPI_REG_CMDCTRL			0x90
+#define	CQSPI_REG_CMDCTRL_EXECUTE_MASK		BIT(0)
+#define	CQSPI_REG_CMDCTRL_INPROGRESS_MASK	BIT(1)
+#define	CQSPI_REG_CMDCTRL_WR_BYTES_LSB		12
+#define	CQSPI_REG_CMDCTRL_WR_EN_LSB		15
+#define	CQSPI_REG_CMDCTRL_ADD_BYTES_LSB		16
+#define	CQSPI_REG_CMDCTRL_ADDR_EN_LSB		19
+#define	CQSPI_REG_CMDCTRL_RD_BYTES_LSB		20
+#define	CQSPI_REG_CMDCTRL_RD_EN_LSB		23
+#define	CQSPI_REG_CMDCTRL_OPCODE_LSB		24
+#define	CQSPI_REG_CMDCTRL_WR_BYTES_MASK		0x7
+#define	CQSPI_REG_CMDCTRL_ADD_BYTES_MASK	0x3
+#define	CQSPI_REG_CMDCTRL_RD_BYTES_MASK		0x7
+#define	CQSPI_REG_INDIRECTWR			0x70
+#define	CQSPI_REG_INDIRECTWR_START_MASK		BIT(0)
+#define	CQSPI_REG_INDIRECTWR_CANCEL_MASK	BIT(1)
+#define	CQSPI_REG_INDIRECTWR_DONE_MASK		BIT(5)
+#define	CQSPI_REG_INDIRECTWRWATERMARK		0x74
+#define	CQSPI_REG_INDIRECTWRSTARTADDR		0x78
+#define	CQSPI_REG_INDIRECTWRBYTES		0x7C
+#define	CQSPI_REG_CMDADDRESS			0x94
+#define	CQSPI_REG_CMDREADDATALOWER		0xA0
+#define	CQSPI_REG_CMDREADDATAUPPER		0xA4
+#define	CQSPI_REG_CMDWRITEDATALOWER		0xA8
+#define	CQSPI_REG_CMDWRITEDATAUPPER		0xAC
+
+/* Interrupt status bits */
+#define CQSPI_REG_IRQ_MODE_ERR			BIT(0)
+#define CQSPI_REG_IRQ_UNDERFLOW			BIT(1)
+#define CQSPI_REG_IRQ_IND_COMP			BIT(2)
+#define CQSPI_REG_IRQ_IND_RD_REJECT		BIT(3)
+#define CQSPI_REG_IRQ_WR_PROTECTED_ERR		BIT(4)
+#define CQSPI_REG_IRQ_ILLEGAL_AHB_ERR		BIT(5)
+#define CQSPI_REG_IRQ_WATERMARK			BIT(6)
+#define CQSPI_REG_IRQ_IND_RD_OVERFLOW		BIT(12)
+#define CQSPI_IRQ_STATUS_ERR		(CQSPI_REG_IRQ_MODE_ERR		| \
+					 CQSPI_REG_IRQ_IND_RD_REJECT	| \
+					 CQSPI_REG_IRQ_WR_PROTECTED_ERR	| \
+					 CQSPI_REG_IRQ_ILLEGAL_AHB_ERR)
+#define CQSPI_IRQ_MASK_RD		(CQSPI_REG_IRQ_MODE_ERR		| \
+					 CQSPI_REG_IRQ_IND_RD_REJECT	| \
+					 CQSPI_REG_IRQ_WATERMARK	| \
+					 CQSPI_REG_IRQ_IND_RD_OVERFLOW	| \
+					 CQSPI_REG_IRQ_IND_COMP)
+#define CQSPI_IRQ_MASK_WR		(CQSPI_REG_IRQ_MODE_ERR		| \
+					 CQSPI_REG_IRQ_WR_PROTECTED_ERR	| \
+					 CQSPI_REG_IRQ_IND_COMP		| \
+					 CQSPI_REG_IRQ_WATERMARK	| \
+					 CQSPI_REG_IRQ_UNDERFLOW)
+
+#define CQSPI_IRQ_STATUS_MASK			(0xFFFFFFFF)
+#define CQSPI_REG_IS_IDLE(base)					\
+		((readl(base + CQSPI_REG_CONFIG) >>		\
+			CQSPI_REG_CONFIG_IDLE_LSB) & 0x1)
+#define CQSPI_CAL_DELAY(tdelay_ns, tref_ns, tsclk_ns)		\
+		((((tdelay_ns) - (tsclk_ns)) / (tref_ns)))
+#define CQSPI_GET_RD_SRAM_LEVEL(reg_basse)			\
+		(((readl(reg_base + CQSPI_REG_SDRAMLEVEL)) >>	\
+		CQSPI_REG_SDRAMLEVEL_RD_LSB) & CQSPI_REG_SDRAMLEVEL_RD_MASK)
+
+struct cqspi_flash_pdata {
+	u32	page_size;
+	u32	block_size;
+	u32	flash_type;
+	u32	quad;
+	u32	read_delay;
+	u32	tshsl_ns;
+	u32	tsd2d_ns;
+	u32	tchsh_ns;
+	u32	tslch_ns;
+};
+
+struct cqspi_platform_data {
+	u32	bus_num;
+	u32	num_chipselect;
+	u32	qspi_ahb_phy;
+	u32	qspi_ahb_size;
+	u32	qspi_ahb_mask;
+	u32	master_ref_clk_hz;
+	u32	ext_decoder;
+	u32	fifo_depth;
+	u32	enable_dma;
+	u32	tx_dma_peri_id;
+	u32	rx_dma_peri_id;
+	u32	trigger_address;
+	bool	is_decoded_cs;
+	bool	rclk_en;
+	struct cqspi_flash_pdata f_pdata[CQSPI_MAX_CHIP_SELECT];
+};
+
+struct struct_cqspi {
+	struct platform_device	*pdev;
+
+	struct clk		*clk;
+	struct clk		*fpi_clk;
+
+	struct reset_control	*reset;
+	struct completion	transfer_complete;
+	struct workqueue_struct	*workqueue;
+	wait_queue_head_t	waitqueue;
+	/* mutex lock for synchronization */
+	struct mutex		lock;
+
+	void __iomem		*iobase;
+	void __iomem		*qspi_ahb_virt;
+	struct resource		*res;
+	struct resource		*res_ahb;
+	resource_size_t		ahb_size;
+
+	struct dma_chan		*rx_chan;
+	struct completion       rx_dma_complete;
+	dma_addr_t		mmap_phys_base;
+	int			dma_done;
+	u32			trigger_address;
+	u32			wr_delay;
+	u32			irq_status;
+	int			current_cs;
+	int			irq;
+	bool			dac_mode;
+};
+
+struct spi_mem_op_cadence {
+	const void	*tx_buf;
+	void		*rx_buf;
+	u32		len;
+	u32		tx_nbits:3;
+	u32		rx_nbits:3;
+};
+
+#endif /* __CADENCE_QSPI__H__ */