@@ -2458,6 +2458,8 @@ static int spi_get_gpio_descs(struct spi_controller *ctlr)
int nb, i;
struct gpio_desc **cs;
struct device *dev = &ctlr->dev;
+ unsigned long native_cs_mask = 0;
+ unsigned int num_cs_gpios = 0;
nb = gpiod_count(dev, "cs");
ctlr->num_chipselect = max_t(int, nb, ctlr->num_chipselect);
@@ -2499,7 +2501,22 @@ static int spi_get_gpio_descs(struct spi_controller *ctlr)
if (!gpioname)
return -ENOMEM;
gpiod_set_consumer_name(cs[i], gpioname);
+ num_cs_gpios++;
+ continue;
+ }
+
+ if (ctlr->max_native_cs && i >= ctlr->max_native_cs) {
+ dev_err(dev, "Invalid native chip select %d\n", i);
+ return -EINVAL;
}
+ native_cs_mask |= BIT(i);
+ }
+
+ ctlr->unused_native_cs = ffz(native_cs_mask);
+ if (num_cs_gpios && ctlr->max_native_cs &&
+ ctlr->unused_native_cs >= ctlr->max_native_cs) {
+ dev_err(dev, "No unused native chip select available\n");
+ return -EINVAL;
}
return 0;
@@ -423,6 +423,12 @@ static inline void spi_unregister_driver(struct spi_driver *sdrv)
* GPIO descriptors rather than using global GPIO numbers grabbed by the
* driver. This will fill in @cs_gpiods and @cs_gpios should not be used,
* and SPI devices will have the cs_gpiod assigned rather than cs_gpio.
+ * @unused_native_cs: When cs_gpiods is used, spi_register_controller() will
+ * fill in this field with the first unused native CS, to be used by SPI
+ * controller drivers that need to drive a native CS when using GPIO CS.
+ * @max_native_cs: When cs_gpiods is used, and this field is filled in,
+ * spi_register_controller() will validate all native CS (including the
+ * unused native CS) against this value.
* @statistics: statistics for the spi_controller
* @dma_tx: DMA transmit channel
* @dma_rx: DMA receive channel
@@ -624,6 +630,8 @@ struct spi_controller {
int *cs_gpios;
struct gpio_desc **cs_gpiods;
bool use_gpio_descriptors;
+ u8 unused_native_cs;
+ u8 max_native_cs;
/* statistics */
struct spi_statistics statistics;
Some SPI master controllers always drive a native chip select when performing a transfer. Hence when using both native and GPIO chip selects, at least one native chip select must be left unused, to be driven when performing transfers with slave devices using GPIO chip selects. Currently, to find an unused native chip select, SPI controller drivers need to parse and process cs-gpios theirselves. This is not only duplicated in each driver that needs it, but also duplicates part of the work done later at SPI controller registration time. Note that this cannot be done after spi_register_controller() returns, as at that time, slave devices may have been probed already. Hence add generic support to the SPI subsystem for finding an unused native chip select. Optionally, this unused native chip select, and all other in-use native chip selects, can be validated against the maximum number of native chip selects available on the controller hardware. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> --- Perhaps the validation is considered overkill ("DT is assumed to be correct")? drivers/spi/spi.c | 17 +++++++++++++++++ include/linux/spi/spi.h | 8 ++++++++ 2 files changed, 25 insertions(+)