diff mbox series

[v4,12/16] mtd: spi-nor: perform a Soft Reset on shutdown

Message ID 20200424184410.8578-13-p.yadav@ti.com (mailing list archive)
State Superseded
Headers show
Series mtd: spi-nor: add xSPI Octal DTR support | expand

Commit Message

Pratyush Yadav April 24, 2020, 6:44 p.m. UTC
A Software Reset sequence will return the flash to Power-on-Reset (POR)
state. It consists of two commands: Soft Reset Enable and Soft Reset.

Perform a Soft Reset on shutdown on flashes that support it so that the
flash can be reset to its initial state and any configurations made by
spi-nor (given that they're only done in volatile registers) will be
reset. This will hand back the flash in pristine state for any further
operations on it.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---
 drivers/mtd/spi-nor/core.c  | 45 +++++++++++++++++++++++++++++++++++++
 drivers/mtd/spi-nor/core.h  |  2 ++
 include/linux/mtd/spi-nor.h |  2 ++
 3 files changed, 49 insertions(+)

Comments

Tudor Ambarus May 10, 2020, 11:22 a.m. UTC | #1
Hi, Pratyush,

On Friday, April 24, 2020 9:44:06 PM EEST Pratyush Yadav wrote:
> A Software Reset sequence will return the flash to Power-on-Reset (POR)
> state. It consists of two commands: Soft Reset Enable and Soft Reset.
> 
> Perform a Soft Reset on shutdown on flashes that support it so that the
> flash can be reset to its initial state and any configurations made by
> spi-nor (given that they're only done in volatile registers) will be
> reset. This will hand back the flash in pristine state for any further
> operations on it.

Please don't introduce SPI_NOR_SOFT_RESET yet. We should instead determine the 
software reset sequence by inspecting BFPT[16], bits 13:8.

Cheers,
ta
Pratyush Yadav May 11, 2020, 6:01 p.m. UTC | #2
On 10/05/20 11:22AM, Tudor.Ambarus@microchip.com wrote:
> Hi, Pratyush,
> 
> On Friday, April 24, 2020 9:44:06 PM EEST Pratyush Yadav wrote:
> > A Software Reset sequence will return the flash to Power-on-Reset (POR)
> > state. It consists of two commands: Soft Reset Enable and Soft Reset.
> > 
> > Perform a Soft Reset on shutdown on flashes that support it so that the
> > flash can be reset to its initial state and any configurations made by
> > spi-nor (given that they're only done in volatile registers) will be
> > reset. This will hand back the flash in pristine state for any further
> > operations on it.
> 
> Please don't introduce SPI_NOR_SOFT_RESET yet. We should instead determine the 
> software reset sequence by inspecting BFPT[16], bits 13:8.
 
 Ok. Will do.
diff mbox series

Patch

diff --git a/drivers/mtd/spi-nor/core.c b/drivers/mtd/spi-nor/core.c
index c75765f09d62..b0f94d6d28bf 100644
--- a/drivers/mtd/spi-nor/core.c
+++ b/drivers/mtd/spi-nor/core.c
@@ -40,6 +40,9 @@ 
 
 #define SPI_NOR_MAX_ADDR_WIDTH	4
 
+#define SPI_NOR_SRST_SLEEP_MIN 200
+#define SPI_NOR_SRST_SLEEP_MAX 400
+
 /**
  * spi_nor_get_cmd_ext() - Get the command opcode extension based on the
  *			   extension type.
@@ -3189,6 +3192,41 @@  static int spi_nor_init(struct spi_nor *nor)
 	return 0;
 }
 
+static void spi_nor_soft_reset(struct spi_nor *nor)
+{
+	struct spi_mem_op op;
+	int ret;
+
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_SRSTEN, 8),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_NO_ADDR,
+			SPI_MEM_OP_NO_DATA);
+	spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev, "Software reset failed: %d\n", ret);
+		return;
+	}
+
+	op = (struct spi_mem_op)SPI_MEM_OP(SPI_MEM_OP_CMD(SPINOR_OP_SRST, 8),
+			SPI_MEM_OP_NO_DUMMY,
+			SPI_MEM_OP_NO_ADDR,
+			SPI_MEM_OP_NO_DATA);
+	spi_nor_spimem_setup_op(nor, &op, SNOR_PROTO_8_8_8_DTR);
+	ret = spi_mem_exec_op(nor->spimem, &op);
+	if (ret) {
+		dev_warn(nor->dev, "Software reset failed: %d\n", ret);
+		return;
+	}
+
+	/*
+	 * Software Reset is not instant, and the delay varies from flash to
+	 * flash. Looking at a few flashes, most range somewhere below 100
+	 * microseconds. So, sleep for a range of 200-400 us.
+	 */
+	usleep_range(SPI_NOR_SRST_SLEEP_MIN, SPI_NOR_SRST_SLEEP_MAX);
+}
+
 /* mtd resume handler */
 static void spi_nor_resume(struct mtd_info *mtd)
 {
@@ -3208,6 +3246,10 @@  void spi_nor_restore(struct spi_nor *nor)
 	if (nor->addr_width == 4 && !(nor->flags & SNOR_F_4B_OPCODES) &&
 	    nor->flags & SNOR_F_BROKEN_RESET)
 		nor->params->set_4byte_addr_mode(nor, false);
+
+	if (nor->info->flags & SPI_NOR_OCTAL_DTR_READ &&
+	    nor->flags & SNOR_F_SOFT_RESET)
+		spi_nor_soft_reset(nor);
 }
 EXPORT_SYMBOL_GPL(spi_nor_restore);
 
@@ -3394,6 +3436,9 @@  int spi_nor_scan(struct spi_nor *nor, const char *name,
 			nor->flags |= SNOR_F_HAS_SR_TB_BIT6;
 	}
 
+	if (info->flags & SPI_NOR_SOFT_RESET)
+		nor->flags |= SNOR_F_SOFT_RESET;
+
 	if (info->flags & NO_CHIP_ERASE)
 		nor->flags |= SNOR_F_NO_OP_CHIP_ERASE;
 	if (info->flags & USE_CLSR)
diff --git a/drivers/mtd/spi-nor/core.h b/drivers/mtd/spi-nor/core.h
index 6338d32a0d77..86c31357b321 100644
--- a/drivers/mtd/spi-nor/core.h
+++ b/drivers/mtd/spi-nor/core.h
@@ -26,6 +26,7 @@  enum spi_nor_option_flags {
 	SNOR_F_HAS_SR_TB_BIT6	= BIT(11),
 	SNOR_F_HAS_4BIT_BP      = BIT(12),
 	SNOR_F_HAS_SR_BP3_BIT6  = BIT(13),
+	SNOR_F_SOFT_RESET	= BIT(14),
 };
 
 struct spi_nor_read_command {
@@ -321,6 +322,7 @@  struct flash_info {
 					 * Must be used with SPI_NOR_4BIT_BP.
 					 */
 #define SPI_NOR_OCTAL_DTR_READ	BIT(19) /* Flash supports octal DTR Read. */
+#define SPI_NOR_SOFT_RESET	BIT(20) /* Flash supports soft reset command */
 
 	/* Part specific fixup hooks. */
 	const struct spi_nor_fixups *fixups;
diff --git a/include/linux/mtd/spi-nor.h b/include/linux/mtd/spi-nor.h
index 9bb41d9401c6..7b828ee1c036 100644
--- a/include/linux/mtd/spi-nor.h
+++ b/include/linux/mtd/spi-nor.h
@@ -51,6 +51,8 @@ 
 #define SPINOR_OP_CLFSR		0x50	/* Clear flag status register */
 #define SPINOR_OP_RDEAR		0xc8	/* Read Extended Address Register */
 #define SPINOR_OP_WREAR		0xc5	/* Write Extended Address Register */
+#define SPINOR_OP_SRSTEN	0x66	/* Software Reset Enable */
+#define SPINOR_OP_SRST		0x99	/* Software Reset */
 
 /* 4-byte address opcodes - used on Spansion and some Macronix flashes. */
 #define SPINOR_OP_READ_4B	0x13	/* Read data bytes (low frequency) */