@@ -343,6 +343,42 @@ static void dw_spi_irq_setup(struct dw_spi *dws)
dws->transfer_handler = dw_spi_transfer_handler;
}
+/*
+ * The iterative procedure of the poll-based transfer is simple: write as much
+ * as possible to the Tx FIFO, wait until the pending to receive data is ready
+ * to be read, read it from the Rx FIFO and check whether the performed
+ * procedure has been successful.
+ *
+ * Note this method the same way as the IRQ-based transfer won't work well for
+ * the SPI devices connected to the controller with native CS due to the
+ * automatic CS assertion/de-assertion.
+ */
+static int dw_spi_poll_transfer(struct dw_spi *dws,
+ struct spi_transfer *transfer)
+{
+ struct spi_delay delay;
+ u16 nbits;
+ int ret;
+
+ delay.unit = SPI_DELAY_UNIT_SCK;
+ nbits = dws->n_bytes * BITS_PER_BYTE;
+
+ do {
+ dw_writer(dws);
+
+ delay.value = nbits * (dws->rx_len - dws->tx_len);
+ spi_delay_exec(&delay, transfer);
+
+ dw_reader(dws);
+
+ ret = dw_spi_check_status(dws, true);
+ if (ret)
+ return ret;
+ } while (dws->rx_len);
+
+ return 0;
+}
+
static int dw_spi_transfer_one(struct spi_controller *master,
struct spi_device *spi, struct spi_transfer *transfer)
{
@@ -387,6 +423,8 @@ static int dw_spi_transfer_one(struct spi_controller *master,
if (dws->dma_mapped)
return dws->dma_ops->dma_transfer(dws, transfer);
+ else if (dws->irq == IRQ_NOTCONNECTED)
+ return dw_spi_poll_transfer(dws, transfer);
dw_spi_irq_setup(dws);
@@ -795,7 +833,7 @@ int dw_spi_add_host(struct device *dev, struct dw_spi *dws)
ret = request_irq(dws->irq, dw_spi_irq, IRQF_SHARED, dev_name(dev),
master);
- if (ret < 0) {
+ if (ret < 0 && ret != -ENOTCONN) {
dev_err(dev, "can not get IRQ\n");
goto err_free_master;
}
A functionality of the poll-based transfer has been removed by commit 1ceb09717e98 ("spi: dw: remove cs_control and poll_mode members from chip_data") with a justification that "there is no user of one anymore". It turns out one of our DW APB SSI core is synthesized with no IRQ line attached and the only possible way of using it is to implement a poll-based SPI transfer procedure. So we have to get the removed functionality back, but with some alterations described below. First of all the poll-based transfer is activated only if the DW SPI controller doesn't have an IRQ line attached and the Linux IRQ number is initialized with the IRQ_NOTCONNECTED value. Secondly the transfer procedure is now executed with a delay performed between writer and reader methods. The delay value is calculated based on the number of data words expected to be received on the current iteration. Finally the errors status is checked on each iteration. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> --- drivers/spi/spi-dw-core.c | 40 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 39 insertions(+), 1 deletion(-)