[v2,2/3] spi: Add SPI_NO_TX/RX support

Commit Message

Alexandru Ardelean Nov. 24, 2020, 10:21 a.m. UTC

From: Dragos Bogdan <[e-mail]>

Transmit/receive only is a valid SPI mode. For example, the MOSI/TX line
might be missing from an ADC while for a DAC the MISO/RX line may be
optional. This patch adds these two new modes: SPI_NO_TX and
SPI_NO_RX. This way, the drivers will be able to identify if any of
these two lines is missing and to adjust the transfers accordingly.

Signed-off-by: Dragos Bogdan <[e-mail]>
Signed-off-by: Alexandru Ardelean <[e-mail]>
---

Changelog v1 -> v2:
* https://lore.kernel.org/linux-spi/[e-mail]/
* convert comment to new multi-line format

 drivers/spi/spi.c       | 26 +++++++++++++++++++++-----
 include/linux/spi/spi.h |  2 ++
 2 files changed, 23 insertions(+), 5 deletions(-)

Patch

diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c
index 0c3f3a962448..5784fa8d9d74 100644
--- a/drivers/spi/spi.c
+++ b/drivers/spi/spi.c
@@ -1939,6 +1939,9 @@  static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
 	/* Device DUAL/QUAD mode */
 	if (!of_property_read_u32(nc, "spi-tx-bus-width", &value)) {
 		switch (value) {
+		case 0:
+			spi->mode |= SPI_NO_TX;
+			break;
 		case 1:
 			break;
 		case 2:
@@ -1960,6 +1963,9 @@  static int of_spi_parse_dt(struct spi_controller *ctlr, struct spi_device *spi,
 
 	if (!of_property_read_u32(nc, "spi-rx-bus-width", &value)) {
 		switch (value) {
+		case 0:
+			spi->mode |= SPI_NO_RX;
+			break;
 		case 1:
 			break;
 		case 2:
@@ -3327,12 +3333,17 @@  int spi_setup(struct spi_device *spi)
 	unsigned	bad_bits, ugly_bits;
 	int		status;
 
-	/* check mode to prevent that DUAL and QUAD set at the same time
+	/*
+	 * check mode to prevent that any two of DUAL, QUAD and NO_MOSI/MISO
+	 * are set at the same time
 	 */
-	if (((spi->mode & SPI_TX_DUAL) && (spi->mode & SPI_TX_QUAD)) ||
-		((spi->mode & SPI_RX_DUAL) && (spi->mode & SPI_RX_QUAD))) {
+	if ((hweight_long(spi->mode &
+		(SPI_TX_DUAL | SPI_TX_QUAD | SPI_NO_TX)) > 1) ||
+	    (hweight_long(spi->mode &
+		(SPI_RX_DUAL | SPI_RX_QUAD | SPI_NO_RX)) > 1)) {
 		dev_err(&spi->dev,
-		"setup: can not select dual and quad at the same time\n");
+		"setup: can not select any two of dual, quad and no-rx/tx "
+		"at the same time\n");
 		return -EINVAL;
 	}
 	/* if it is SPI_3WIRE mode, DUAL and QUAD should be forbidden
@@ -3346,7 +3357,8 @@  int spi_setup(struct spi_device *spi)
 	 * SPI_CS_WORD has a fallback software implementation,
 	 * so it is ignored here.
 	 */
-	bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD);
+	bad_bits = spi->mode & ~(spi->controller->mode_bits | SPI_CS_WORD |
+				 SPI_NO_TX | SPI_NO_RX);
 	/* nothing prevents from working with active-high CS in case if it
 	 * is driven by GPIO.
 	 */
@@ -3607,6 +3619,8 @@  static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 		 * 2. check tx/rx_nbits match the mode in spi_device
 		 */
 		if (xfer->tx_buf) {
+			if (spi->mode & SPI_NO_TX)
+				return -EINVAL;
 			if (xfer->tx_nbits != SPI_NBITS_SINGLE &&
 				xfer->tx_nbits != SPI_NBITS_DUAL &&
 				xfer->tx_nbits != SPI_NBITS_QUAD)
@@ -3620,6 +3634,8 @@  static int __spi_validate(struct spi_device *spi, struct spi_message *message)
 		}
 		/* check transfer rx_nbits */
 		if (xfer->rx_buf) {
+			if (spi->mode & SPI_NO_RX)
+				return -EINVAL;
 			if (xfer->rx_nbits != SPI_NBITS_SINGLE &&
 				xfer->rx_nbits != SPI_NBITS_DUAL &&
 				xfer->rx_nbits != SPI_NBITS_QUAD)
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 66c7d8e45563..8f3343d3ac27 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -186,6 +186,8 @@  struct spi_device {
 #define	SPI_TX_OCTAL	BIT(13)			/* transmit with 8 wires */
 #define	SPI_RX_OCTAL	BIT(14)			/* receive with 8 wires */
 #define	SPI_3WIRE_HIZ	BIT(15)			/* high impedance turnaround */
+#define	SPI_NO_TX	BIT(16)			/* no transmit wire */
+#define	SPI_NO_RX	BIT(17)			/* no receive wire */
 	int			irq;
 	void			*controller_state;
 	void			*controller_data;