@@ -273,7 +273,7 @@ static u32 dw_spi_prepare_cr0(struct dw_spi *dws, struct spi_device *spi)
if (!(dws->caps & DW_SPI_CAP_DWC_SSI)) {
/* CTRLR0[ 5: 4] Frame Format */
- cr0 |= SSI_MOTO_SPI << SPI_FRF_OFFSET;
+ cr0 |= SPI_FRF_MOTO_SPI << SPI_FRF_OFFSET;
/*
* SPI mode (SCPOL|SCPH)
@@ -287,7 +287,7 @@ static u32 dw_spi_prepare_cr0(struct dw_spi *dws, struct spi_device *spi)
cr0 |= ((spi->mode & SPI_LOOP) ? 1 : 0) << SPI_SRL_OFFSET;
} else {
/* CTRLR0[ 7: 6] Frame Format */
- cr0 |= SSI_MOTO_SPI << DWC_SSI_CTRLR0_FRF_OFFSET;
+ cr0 |= SPI_FRF_MOTO_SPI << DWC_SSI_CTRLR0_FRF_OFFSET;
/*
* SPI mode (SCPOL|SCPH)
@@ -46,9 +46,9 @@
#define SPI_DFS32_OFFSET 16
#define SPI_FRF_OFFSET 4
-#define SPI_FRF_SPI 0x0
-#define SPI_FRF_SSP 0x1
-#define SPI_FRF_MICROWIRE 0x2
+#define SPI_FRF_MOTO_SPI 0x0
+#define SPI_FRF_TI_SSP 0x1
+#define SPI_FRF_NS_MICROWIRE 0x2
#define SPI_FRF_RESV 0x3
#define SPI_MODE_OFFSET 6
@@ -114,12 +114,6 @@
#define SPI_GET_BYTE(_val, _idx) \
((_val) >> (BITS_PER_BYTE * (_idx)) & 0xff)
-enum dw_ssi_type {
- SSI_MOTO_SPI = 0,
- SSI_TI_SSP,
- SSI_NS_MICROWIRE,
-};
-
/* DW SPI capabilities */
#define DW_SPI_CAP_CS_OVERRIDE BIT(0)
#define DW_SPI_CAP_KEEMBAY_MST BIT(1)
The dw_ssi_type enumeration describes the SPI frame formats the controller supports, like Motorola SPI, Texas Instruments SSP and National Semiconductors Microwire, that is the serial protocol utilized for the SPI-transfers. Depending on the DW SSI IP-core configuration the protocol could be either fixed or selectable. If it is changebale the protocol can be selected by means of the CTRL0.FRF field, which possible values encoded by the dw_ssi_type enumeration. Aside with the denoted enum the field values are also described by a set of SPI_FRF_{SPI,SSP,MICROWIRE} macros. Thus currently the DW SPI driver has got two entities describing the same data. Let's get rid of the enumeration one then, since first it hasn't been used as enumeration-type but merely as a parametrized values set and second that would unify the macro-based CSR read/write interface of the driver. While at it convert the macro names to be more descriptive about the protocols they represent. Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru> --- drivers/spi/spi-dw-core.c | 4 ++-- drivers/spi/spi-dw.h | 12 +++--------- 2 files changed, 5 insertions(+), 11 deletions(-)