| Message ID | 20220201012956.563272-1-linus.walleij@linaro.org (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | b651d1da86aa525c5a5b2bd61f528353c28d589d |
| Headers | show |
| Series | [v2] spi: bcm2835aux: Convert to use GPIO descriptors | expand |
On Tue, 1 Feb 2022 02:29:56 +0100, Linus Walleij wrote: > This one is pretty straight forward to switch over, the driver > already relies on inspecting cs_gpio just check cs_gpiod instead > and stop the special handling of requesting the GPIO and stuff > the core will take care of. > > Applied to https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next Thanks! [1/1] spi: bcm2835aux: Convert to use GPIO descriptors commit: b651d1da86aa525c5a5b2bd61f528353c28d589d All being well this means that it will be integrated into the linux-next tree (usually sometime in the next 24 hours) and sent to Linus during the next merge window (or sooner if it is a bug fix), however if problems are discovered then the patch may be dropped or reverted. You may get further e-mails resulting from automated or manual testing and review of the tree, please engage with people reporting problems and send followup patches addressing any issues that are reported if needed. If any updates are required or you are submitting further changes they should be sent as incremental updates against current git, existing patches will not be replaced. Please add any relevant lists and maintainers to the CCs when replying to this mail. Thanks, Mark
diff --git a/drivers/spi/spi-bcm2835aux.c b/drivers/spi/spi-bcm2835aux.c index 7d709a8c833b..e28521922330 100644 --- a/drivers/spi/spi-bcm2835aux.c +++ b/drivers/spi/spi-bcm2835aux.c @@ -22,7 +22,6 @@ #include <linux/of.h> #include <linux/of_address.h> #include <linux/of_device.h> -#include <linux/of_gpio.h> #include <linux/of_irq.h> #include <linux/regmap.h> #include <linux/spi/spi.h> @@ -445,25 +444,12 @@ static void bcm2835aux_spi_handle_err(struct spi_master *master, static int bcm2835aux_spi_setup(struct spi_device *spi) { - int ret; - /* sanity check for native cs */ if (spi->mode & SPI_NO_CS) return 0; - if (gpio_is_valid(spi->cs_gpio)) { - /* with gpio-cs set the GPIO to the correct level - * and as output (in case the dt has the gpio not configured - * as output but native cs) - */ - ret = gpio_direction_output(spi->cs_gpio, - (spi->mode & SPI_CS_HIGH) ? 0 : 1); - if (ret) - dev_err(&spi->dev, - "could not set gpio %i as output: %i\n", - spi->cs_gpio, ret); - - return ret; - } + + if (spi->cs_gpiod) + return 0; /* for dt-backwards compatibility: only support native on CS0 * known things not supported with broken native CS: @@ -519,6 +505,7 @@ static int bcm2835aux_spi_probe(struct platform_device *pdev) master->prepare_message = bcm2835aux_spi_prepare_message; master->unprepare_message = bcm2835aux_spi_unprepare_message; master->dev.of_node = pdev->dev.of_node; + master->use_gpio_descriptors = true; bs = spi_master_get_devdata(master);
This one is pretty straight forward to switch over, the driver already relies on inspecting cs_gpio just check cs_gpiod instead and stop the special handling of requesting the GPIO and stuff the core will take care of. Cc: Lukas Wunner <lukas@wunner.de> Cc: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> --- ChangeLog v1->v2: - Drop an unused "ret" variable that was causing build noise. --- drivers/spi/spi-bcm2835aux.c | 21 ++++----------------- 1 file changed, 4 insertions(+), 17 deletions(-)