diff mbox series

[07/10] spi: spi-zynqmp-gqspi: Add stacked memories support in GQSPI driver

Message ID 20221017121249.19061-8-amit.kumar-mahapatra@amd.com (mailing list archive)
State New, archived
Headers show
Series spi: Add support for stacked/parallel memories | expand

Commit Message

Mahapatra, Amit Kumar Oct. 17, 2022, 12:12 p.m. UTC 
GQSPI supports two chip select CS0 & CS1. Update the driver to
assert/de-assert the appropriate chip select as per the bits set in
qspi->cs_index_mask.

Signed-off-by: Amit Kumar Mahapatra <amit.kumar-mahapatra@amd.com>
---
 drivers/spi/spi-zynqmp-gqspi.c | 21 +++++++++++++--------
 1 file changed, 13 insertions(+), 8 deletions(-)
diff mbox series

Patch

diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index 35ff734fb82d..4759f704bf5c 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -156,6 +156,9 @@ 
 #define GQSPI_FREQ_100MHZ	100000000
 #define GQSPI_FREQ_150MHZ	150000000
 
+#define GQSPI_SELECT_LOWER_CS  BIT(0)
+#define GQSPI_SELECT_UPPER_CS  BIT(1)
+
 #define SPI_AUTOSUSPEND_TIMEOUT		3000
 enum mode_type {GQSPI_MODE_IO, GQSPI_MODE_DMA};
 
@@ -467,15 +470,17 @@  static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
 
 	genfifoentry |= GQSPI_GENFIFO_MODE_SPI;
 
+	if (qspi->cs_index_mask & GQSPI_SELECT_UPPER_CS) {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_UPPER,
+					 GQSPI_SELECT_FLASH_BUS_LOWER);
+	} else if (qspi->cs_index_mask & GQSPI_SELECT_LOWER_CS) {
+		zynqmp_gqspi_selectslave(xqspi,
+					 GQSPI_SELECT_FLASH_CS_LOWER,
+					 GQSPI_SELECT_FLASH_BUS_LOWER);
+	}
+	genfifoentry |= xqspi->genfifobus;
 	if (!is_high) {
-		if (!qspi->chip_select[0]) {
-			xqspi->genfifobus = GQSPI_GENFIFO_BUS_LOWER;
-			xqspi->genfifocs = GQSPI_GENFIFO_CS_LOWER;
-		} else {
-			xqspi->genfifobus = GQSPI_GENFIFO_BUS_UPPER;
-			xqspi->genfifocs = GQSPI_GENFIFO_CS_UPPER;
-		}
-		genfifoentry |= xqspi->genfifobus;
 		genfifoentry |= xqspi->genfifocs;
 		genfifoentry |= GQSPI_GENFIFO_CS_SETUP;
 	} else {