@@ -194,9 +194,6 @@ The following logic is used to determine the type of I/O to be used on
a per "spi_transfer" basis::
if spi_message.len > 65536 then
- if spi_message.is_dma_mapped or rx_dma_buf != 0 or tx_dma_buf != 0 then
- reject premapped transfers
-
print "rate limited" warning
use PIO transfers
@@ -419,10 +419,6 @@ any more such messages.
to make extra copies unless the hardware requires it (e.g. working
around hardware errata that force the use of bounce buffering).
- If standard dma_map_single() handling of these buffers is inappropriate,
- you can use spi_message.is_dma_mapped to tell the controller driver
- that you've already provided the relevant DMA addresses.
-
- The basic I/O primitive is spi_async(). Async requests may be
issued in any context (irq handler, task, etc) and completion
is reported using a callback provided with the message.
@@ -987,8 +987,6 @@ static void atmel_spi_pdc_next_xfer(struct spi_controller *host,
* For DMA, tx_buf/tx_dma have the same relationship as rx_buf/rx_dma:
* - The buffer is either valid for CPU access, else NULL
* - If the buffer is valid, so is its DMA address
- *
- * This driver manages the dma address unless message->is_dma_mapped.
*/
static int
atmel_spi_dma_map_xfer(struct atmel_spi *as, struct spi_transfer *xfer)
@@ -1374,8 +1372,7 @@ static int atmel_spi_one_transfer(struct spi_controller *host,
* DMA map early, for performance (empties dcache ASAP) and
* better fault reporting.
*/
- if ((!host->cur_msg->is_dma_mapped)
- && as->use_pdc) {
+ if (as->use_pdc) {
if (atmel_spi_dma_map_xfer(as, xfer) < 0)
return -ENOMEM;
}
@@ -1454,8 +1451,7 @@ static int atmel_spi_one_transfer(struct spi_controller *host,
}
}
- if (!host->cur_msg->is_dma_mapped
- && as->use_pdc)
+ if (as->use_pdc)
atmel_spi_dma_unmap_xfer(host, xfer);
if (as->use_pdc)
@@ -959,16 +959,6 @@ static int pxa2xx_spi_transfer_one(struct spi_controller *controller,
/* Check if we can DMA this transfer */
if (transfer->len > MAX_DMA_LEN && chip->enable_dma) {
-
- /* Reject already-mapped transfers; PIO won't always work */
- if (message->is_dma_mapped
- || transfer->rx_dma || transfer->tx_dma) {
- dev_err(&spi->dev,
- "Mapped transfer length of %u is greater than %d\n",
- transfer->len, MAX_DMA_LEN);
- return -EINVAL;
- }
-
/* Warn ... we force this to PIO mode */
dev_warn_ratelimited(&spi->dev,
"DMA disabled for transfer length %u greater than %d\n",
@@ -3709,9 +3709,6 @@ static int __spi_split_transfer_maxsize(struct spi_controller *ctlr,
* to the same values as *xferp, so tx_buf, rx_buf and len
* are all identical (as well as most others)
* so we just have to fix up len and the pointers.
- *
- * This also includes support for the depreciated
- * spi_message.is_dma_mapped interface.
*/
/*
@@ -3725,12 +3722,8 @@ static int __spi_split_transfer_maxsize(struct spi_controller *ctlr,
/* Update rx_buf, tx_buf and DMA */
if (xfers[i].rx_buf)
xfers[i].rx_buf += offset;
- if (xfers[i].rx_dma)
- xfers[i].rx_dma += offset;
if (xfers[i].tx_buf)
xfers[i].tx_buf += offset;
- if (xfers[i].tx_dma)
- xfers[i].tx_dma += offset;
/* Update length */
xfers[i].len = min(maxsize, xfers[i].len - offset);
@@ -957,8 +957,8 @@ struct spi_res {
* struct spi_transfer - a read/write buffer pair
* @tx_buf: data to be written (DMA-safe memory), or NULL
* @rx_buf: data to be read (DMA-safe memory), or NULL
- * @tx_dma: DMA address of tx_buf, if @spi_message.is_dma_mapped
- * @rx_dma: DMA address of rx_buf, if @spi_message.is_dma_mapped
+ * @tx_dma: DMA address of tx_buf, currently not for client use
+ * @rx_dma: DMA address of rx_buf, currently not for client use
* @tx_nbits: number of bits used for writing. If 0 the default
* (SPI_NBITS_SINGLE) is used.
* @rx_nbits: number of bits used for reading. If 0 the default
@@ -1068,8 +1068,7 @@ struct spi_transfer {
/*
* It's okay if tx_buf == rx_buf (right?).
* For MicroWire, one buffer must be NULL.
- * Buffers must work with dma_*map_single() calls, unless
- * spi_message.is_dma_mapped reports a pre-existing mapping.
+ * Buffers must work with dma_*map_single() calls.
*/
const void *tx_buf;
void *rx_buf;
@@ -1113,8 +1112,6 @@ struct spi_transfer {
* struct spi_message - one multi-segment SPI transaction
* @transfers: list of transfer segments in this transaction
* @spi: SPI device to which the transaction is queued
- * @is_dma_mapped: if true, the caller provided both DMA and CPU virtual
- * addresses for each transfer buffer
* @pre_optimized: peripheral driver pre-optimized the message
* @optimized: the message is in the optimized state
* @prepared: spi_prepare_message was called for the this message
@@ -1148,8 +1145,6 @@ struct spi_message {
struct spi_device *spi;
- unsigned is_dma_mapped:1;
-
/* spi_optimize_message() was called for this message */
bool pre_optimized;
/* __spi_optimize_message() was called for this message */
There are no more users of the deprecated is_dma_mapped in struct spi_message so it can be removed. References in documentation and comments are also removed. A few similar checks if xfer->tx_dma or xfer->rx_dma are not NULL are also removed since these are now guaranteed to be NULL because they were previously set only if is_dma_mapped was true. Signed-off-by: David Lechner <dlechner@baylibre.com> --- Documentation/spi/pxa2xx.rst | 3 --- Documentation/spi/spi-summary.rst | 4 ---- drivers/spi/spi-atmel.c | 8 ++------ drivers/spi/spi-pxa2xx.c | 10 ---------- drivers/spi/spi.c | 7 ------- include/linux/spi/spi.h | 11 +++-------- 6 files changed, 5 insertions(+), 38 deletions(-) --- base-commit: 593c0afc18da08bbb79c7af2a6668884987958f6 change-id: 20240315-spi-remove-is_dma_mapped-ac067635662e