| Message ID | 20240514104508.938448-4-prajna.rajendrakumar@microchip.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | 9c84429324ea2b5bc537ef8ec7d3727579d37116 |
| Headers | show |
| Series | Add support for GPIO based CS | expand |
Prajna, Mark, On Tue, May 14, 2024 at 11:45:08AM +0100, Prajna Rajendra Kumar wrote: > The SPI "hard" controller within the PolarFire SoC is capable of > handling eight CS lines, but only one CS line is wired. Therefore, use > GPIO descriptors to configure additional CS lines. > > Signed-off-by: Prajna Rajendra Kumar <prajna.rajendrakumar@microchip.com> I provided an ack on v1, so here it is again: Acked-by: Conor Dooley <conor.dooley@microchip.com> In general you can keep tags between versions, if you intentionally drop tags you should mention why you dropped them. > --- > drivers/spi/spi-microchip-core.c | 4 ++++ > 1 file changed, 4 insertions(+) > > diff --git a/drivers/spi/spi-microchip-core.c b/drivers/spi/spi-microchip-core.c > index c10de45aa472..6246254e1dff 100644 > --- a/drivers/spi/spi-microchip-core.c > +++ b/drivers/spi/spi-microchip-core.c > @@ -258,6 +258,9 @@ static int mchp_corespi_setup(struct spi_device *spi) > struct mchp_corespi *corespi = spi_controller_get_devdata(spi->controller); > u32 reg; > > + if (spi_is_csgpiod(spi)) > + return 0; Mark, This has no users outside of core code, but is < 6 months old. Is using it in a driver like this okay? Cheers, Conor. > + > /* > * Active high targets need to be specifically set to their inactive > * states during probe by adding them to the "control group" & thus > @@ -516,6 +519,7 @@ static int mchp_corespi_probe(struct platform_device *pdev) > > host->num_chipselect = num_cs; > host->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; > + host->use_gpio_descriptors = true; > host->setup = mchp_corespi_setup; > host->bits_per_word_mask = SPI_BPW_MASK(8); > host->transfer_one = mchp_corespi_transfer_one; > -- > 2.25.1 > > > _______________________________________________ > linux-riscv mailing list > linux-riscv@lists.infradead.org > http://lists.infradead.org/mailman/listinfo/linux-riscv
diff --git a/drivers/spi/spi-microchip-core.c b/drivers/spi/spi-microchip-core.c index c10de45aa472..6246254e1dff 100644 --- a/drivers/spi/spi-microchip-core.c +++ b/drivers/spi/spi-microchip-core.c @@ -258,6 +258,9 @@ static int mchp_corespi_setup(struct spi_device *spi) struct mchp_corespi *corespi = spi_controller_get_devdata(spi->controller); u32 reg; + if (spi_is_csgpiod(spi)) + return 0; + /* * Active high targets need to be specifically set to their inactive * states during probe by adding them to the "control group" & thus @@ -516,6 +519,7 @@ static int mchp_corespi_probe(struct platform_device *pdev) host->num_chipselect = num_cs; host->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH; + host->use_gpio_descriptors = true; host->setup = mchp_corespi_setup; host->bits_per_word_mask = SPI_BPW_MASK(8); host->transfer_one = mchp_corespi_transfer_one;
The SPI "hard" controller within the PolarFire SoC is capable of handling eight CS lines, but only one CS line is wired. Therefore, use GPIO descriptors to configure additional CS lines. Signed-off-by: Prajna Rajendra Kumar <prajna.rajendrakumar@microchip.com> --- drivers/spi/spi-microchip-core.c | 4 ++++ 1 file changed, 4 insertions(+)