new file mode 100644
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/fsl,espi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale eSPI (Enhanced Serial Peripheral Interface) controller
+
+maintainers:
+ - J. Neuschäfer <j.ne@posteo.net>
+
+properties:
+ compatible:
+ const: fsl,mpc8536-espi
+
+ reg:
+ maxItems: 1
+
+ interrupts:
+ maxItems: 1
+
+ fsl,espi-num-chipselects:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ enum: [ 1, 4 ]
+ description: The number of the chipselect signals.
+
+ fsl,csbef:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ description: Chip select assertion time in bits before frame starts
+
+ fsl,csaft:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ minimum: 0
+ maximum: 15
+ description: Chip select negation time in bits after frame ends
+
+required:
+ - compatible
+ - reg
+ - interrupts
+ - fsl,espi-num-chipselects
+
+allOf:
+ - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi@110000 {
+ compatible = "fsl,mpc8536-espi";
+ reg = <0x110000 0x1000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ interrupts = <53 IRQ_TYPE_EDGE_FALLING>;
+ fsl,espi-num-chipselects = <4>;
+ fsl,csbef = <1>;
+ fsl,csaft = <1>;
+ };
+
+...
new file mode 100644
@@ -0,0 +1,74 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/spi/fsl,spi.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Freescale SPI (Serial Peripheral Interface) controller
+
+maintainers:
+ - J. Neuschäfer <j.ne@posteo.net>
+
+properties:
+ compatible:
+ enum:
+ - fsl,spi
+ - aeroflexgaisler,spictrl
+
+ reg:
+ maxItems: 1
+
+ cell-index:
+ $ref: /schemas/types.yaml#/definitions/uint32
+ description: |
+ QE SPI subblock index.
+ 0: QE subblock SPI1
+ 1: QE subblock SPI2
+
+ mode:
+ description: SPI operation mode
+ enum:
+ - cpu
+ - cpu-qe
+
+ interrupts:
+ maxItems: 1
+
+ clock-frequency:
+ description: input clock frequency to non FSL_SOC cores
+
+ cs-gpios: true
+
+ fsl,spisel_boot:
+ $ref: /schemas/types.yaml#/definitions/flag
+ description:
+ For the MPC8306 and MPC8309, specifies that the SPISEL_BOOT signal is used
+ as chip select for a slave device. Use reg = <number of gpios> in the
+ corresponding child node, i.e. 0 if the cs-gpios property is not present.
+
+required:
+ - compatible
+ - reg
+ - mode
+ - interrupts
+
+allOf:
+ - $ref: spi-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interrupt-controller/irq.h>
+
+ spi@4c0 {
+ compatible = "fsl,spi";
+ reg = <0x4c0 0x40>;
+ cell-index = <0>;
+ interrupts = <82 0>;
+ mode = "cpu";
+ cs-gpios = <&gpio 18 IRQ_TYPE_EDGE_RISING // device reg=<0>
+ &gpio 19 IRQ_TYPE_EDGE_RISING>; // device reg=<1>
+ };
+
+...
deleted file mode 100644
@@ -1,62 +0,0 @@
-* SPI (Serial Peripheral Interface)
-
-Required properties:
-- cell-index : QE SPI subblock index.
- 0: QE subblock SPI1
- 1: QE subblock SPI2
-- compatible : should be "fsl,spi" or "aeroflexgaisler,spictrl".
-- mode : the SPI operation mode, it can be "cpu" or "cpu-qe".
-- reg : Offset and length of the register set for the device
-- interrupts : <a b> where a is the interrupt number and b is a
- field that represents an encoding of the sense and level
- information for the interrupt. This should be encoded based on
- the information in section 2) depending on the type of interrupt
- controller you have.
-- clock-frequency : input clock frequency to non FSL_SOC cores
-
-Optional properties:
-- cs-gpios : specifies the gpio pins to be used for chipselects.
- The gpios will be referred to as reg = <index> in the SPI child nodes.
- If unspecified, a single SPI device without a chip select can be used.
-- fsl,spisel_boot : for the MPC8306 and MPC8309, specifies that the
- SPISEL_BOOT signal is used as chip select for a slave device. Use
- reg = <number of gpios> in the corresponding child node, i.e. 0 if
- the cs-gpios property is not present.
-
-Example:
- spi@4c0 {
- cell-index = <0>;
- compatible = "fsl,spi";
- reg = <4c0 40>;
- interrupts = <82 0>;
- interrupt-parent = <700>;
- mode = "cpu";
- cs-gpios = <&gpio 18 1 // device reg=<0>
- &gpio 19 1>; // device reg=<1>
- };
-
-
-* eSPI (Enhanced Serial Peripheral Interface)
-
-Required properties:
-- compatible : should be "fsl,mpc8536-espi".
-- reg : Offset and length of the register set for the device.
-- interrupts : should contain eSPI interrupt, the device has one interrupt.
-- fsl,espi-num-chipselects : the number of the chipselect signals.
-
-Optional properties:
-- fsl,csbef: chip select assertion time in bits before frame starts
-- fsl,csaft: chip select negation time in bits after frame ends
-
-Example:
- spi@110000 {
- #address-cells = <1>;
- #size-cells = <0>;
- compatible = "fsl,mpc8536-espi";
- reg = <0x110000 0x1000>;
- interrupts = <53 0x2>;
- interrupt-parent = <&mpic>;
- fsl,espi-num-chipselects = <4>;
- fsl,csbef = <1>;
- fsl,csaft = <1>;
- };