@@ -32,16 +32,22 @@
#define UART_MCR 0x04 /* Modem control */
#define UART_LSR 0x05 /* line status */
#define UART_MSR 0x06 /* Modem status */
+#define UART_SCR 0x07 /* Scratch pad */
#define UART_USR 0x1f /* Status register (DW) */
#define UART_DLL 0x00 /* divisor latch (ls) (DLAB=1) */
#define UART_DLM 0x01 /* divisor latch (ms) (DLAB=1) */
#define UART_XR_EFR 0x09 /* Enhanced function register (Exar) */
+/* ns8250 emulator: range of emulated registers [0..UART_MAX-1] */
+#define UART_MAX (UART_SCR + 1)
+
/* Interrupt Enable Register */
#define UART_IER_ERDAI 0x01 /* rx data recv'd */
#define UART_IER_ETHREI 0x02 /* tx reg. empty */
#define UART_IER_ELSI 0x04 /* rx line status */
#define UART_IER_EMSI 0x08 /* MODEM status */
+#define UART_IER_MASK \
+ (UART_IER_ERDAI | UART_IER_ETHREI | UART_IER_ELSI | UART_IER_EMSI)
/* Interrupt Identification Register */
#define UART_IIR_NOINT 0x01 /* no interrupt pending */
@@ -51,12 +57,21 @@
#define UART_IIR_THR 0x02 /* - tx reg. empty */
#define UART_IIR_MSI 0x00 /* - MODEM status */
#define UART_IIR_BSY 0x07 /* - busy detect (DW) */
+#define UART_IIR_FE0 BIT(6, U) /* FIFO enable #0 */
+#define UART_IIR_FE1 BIT(7, U) /* FIFO enable #1 */
+#define UART_IIR_FE_MASK (UART_IIR_FE0 | UART_IIR_FE1)
/* FIFO Control Register */
-#define UART_FCR_ENABLE 0x01 /* enable FIFO */
-#define UART_FCR_CLRX 0x02 /* clear Rx FIFO */
-#define UART_FCR_CLTX 0x04 /* clear Tx FIFO */
-#define UART_FCR_DMA 0x10 /* enter DMA mode */
+#define UART_FCR_ENABLE BIT(0, U) /* enable FIFO */
+#define UART_FCR_CLRX BIT(1, U) /* clear Rx FIFO */
+#define UART_FCR_CLTX BIT(2, U) /* clear Tx FIFO */
+#define UART_FCR_DMA BIT(3, U) /* enter DMA mode */
+#define UART_FCR_RESERVED0 BIT(4, U) /* reserved; always 0 */
+#define UART_FCR_RESERVED1 BIT(5, U) /* reserved; always 0 */
+#define UART_FCR_RTB0 BIT(6, U) /* receiver trigger bit #0 */
+#define UART_FCR_RTB1 BIT(7, U) /* receiver trigger bit #1 */
+#define UART_FCR_TRG_MASK (UART_FCR_RTB0 | UART_FCR_RTB1)
+
#define UART_FCR_TRG1 0x00 /* Rx FIFO trig lev 1 */
#define UART_FCR_TRG4 0x40 /* Rx FIFO trig lev 4 */
#define UART_FCR_TRG8 0x80 /* Rx FIFO trig lev 8 */
@@ -64,17 +79,17 @@
/*
* Note: The FIFO trigger levels are chip specific:
- * RX:76 = 00 01 10 11 TX:54 = 00 01 10 11
- * PC16550D: 1 4 8 14 xx xx xx xx
- * TI16C550A: 1 4 8 14 xx xx xx xx
- * TI16C550C: 1 4 8 14 xx xx xx xx
- * ST16C550: 1 4 8 14 xx xx xx xx
- * ST16C650: 8 16 24 28 16 8 24 30 PORT_16650V2
- * NS16C552: 1 4 8 14 xx xx xx xx
- * ST16C654: 8 16 56 60 8 16 32 56 PORT_16654
- * TI16C750: 1 16 32 56 xx xx xx xx PORT_16750
- * TI16C752: 8 16 56 60 8 16 32 56
- * Tegra: 1 4 8 14 16 8 4 1 PORT_TEGRA
+ * RX:76 = 00 01 10 11 TX:54 = 00 01 10 11
+ * PC16550D: 1 4 8 14 xx xx xx xx
+ * TI16C550A: 1 4 8 14 xx xx xx xx
+ * TI16C550C: 1 4 8 14 xx xx xx xx
+ * ST16C550: 1 4 8 14 xx xx xx xx
+ * ST16C650: 8 16 24 28 16 8 24 30 PORT_16650V2
+ * NS16C552: 1 4 8 14 xx xx xx xx
+ * ST16C654: 8 16 56 60 8 16 32 56 PORT_16654
+ * TI16C750: 1 16 32 56 xx xx xx xx PORT_16750
+ * TI16C752: 8 16 56 60 8 16 32 56
+ * Tegra: 1 4 8 14 16 8 4 1 PORT_TEGRA
*/
#define UART_FCR_R_TRIG_00 0x00
#define UART_FCR_R_TRIG_01 0x40
@@ -96,11 +111,31 @@
#define UART_LCR_CONF_MODE_B 0xBF /* Configuration mode B */
/* Modem Control Register */
-#define UART_MCR_DTR 0x01 /* Data Terminal Ready */
-#define UART_MCR_RTS 0x02 /* Request to Send */
-#define UART_MCR_OUT2 0x08 /* OUT2: interrupt mask */
-#define UART_MCR_LOOP 0x10 /* Enable loopback test mode */
-#define UART_MCR_TCRTLR 0x40 /* Access TCR/TLR (TI16C752, EFR[4]=1) */
+#define UART_MCR_DTR BIT(0, U) /* Data Terminal Ready */
+#define UART_MCR_RTS BIT(1, U) /* Request to Send */
+#define UART_MCR_OUT1 BIT(2, U) /* OUT1: interrupt mask */
+#define UART_MCR_OUT2 BIT(3, U) /* OUT2: interrupt mask */
+#define UART_MCR_LOOP BIT(4, U) /* Enable loopback test mode */
+#define UART_MCR_RESERVED0 BIT(5, U) /* Reserved #0 */
+#define UART_MCR_RESERVED1 BIT(6, U) /* Reserved #1 */
+#define UART_MCR_TCRTLR BIT(6, U) /* Access TCR/TLR (TI16C752, EFR[4]=1) */
+#define UART_MCR_RESERVED2 BIT(7, U) /* Reserved #2 */
+#define UART_MCR_MASK \
+ (UART_MCR_DTR | UART_MCR_RTS | \
+ UART_MCR_OUT1 | UART_MCR_OUT2 | \
+ UART_MCR_LOOP)
+
+/* Modem Status Register */
+#define UART_MSR_DCTS BIT(0, U) /* Change in CTS */
+#define UART_MSR_DDSR BIT(1, U) /* Change in DSR */
+#define UART_MSR_TERI BIT(2, U) /* Change in RI */
+#define UART_MSR_DDCD BIT(3, U) /* Change in CTS */
+#define UART_MSR_CTS BIT(4, U)
+#define UART_MSR_DSR BIT(5, U)
+#define UART_MSR_RI BIT(6, U)
+#define UART_MSR_DCD BIT(7, U)
+#define UART_MSR_DELTA \
+ (UART_MSR_DCTS | UART_MSR_DDSR | UART_MSR_TERI | UART_MSR_DDCD)
/* Line Status Register */
#define UART_LSR_DR 0x01 /* Data ready */
@@ -111,6 +146,7 @@
#define UART_LSR_THRE 0x20 /* Xmit hold reg empty */
#define UART_LSR_TEMT 0x40 /* Xmitter empty */
#define UART_LSR_ERR 0x80 /* Error */
+#define UART_LSR_MASK (UART_LSR_OE | UART_LSR_BI)
/* These parity settings can be ORed directly into the LCR. */
#define UART_PARITY_NONE (0<<3)
@@ -119,7 +155,10 @@
#define UART_PARITY_MARK (5<<3)
#define UART_PARITY_SPACE (7<<3)
-/* Frequency of external clock source. This definition assumes PC platform. */
+/*
+ * Frequency of external UART clock source.
+ * Same as IBM PC master input clock frequency.
+ */
#define UART_CLOCK_HZ 1843200
/* Bits in Exar specific UART_XR_EFR register */