From patchwork Fri Dec 13 12:42:19 2019 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Thomas Bogendoerfer X-Patchwork-Id: 11290483 Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 6989A18B6 for ; Fri, 13 Dec 2019 20:36:48 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by mail.kernel.org (Postfix) with ESMTP id 26910246AE for ; Fri, 13 Dec 2019 20:36:48 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1727140AbfLMMm6 (ORCPT ); Fri, 13 Dec 2019 07:42:58 -0500 Received: from mx2.suse.de ([195.135.220.15]:42698 "EHLO mx1.suse.de" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1727041AbfLMMm5 (ORCPT ); Fri, 13 Dec 2019 07:42:57 -0500 X-Virus-Scanned: by amavisd-new at test-mx.suse.de Received: from relay2.suse.de (unknown [195.135.220.254]) by mx1.suse.de (Postfix) with ESMTP id D0DD2B0DA; Fri, 13 Dec 2019 12:42:54 +0000 (UTC) From: Thomas Bogendoerfer To: Ralf Baechle , Paul Burton , James Hogan , Lee Jones , "David S. Miller" , Alessandro Zummo , Alexandre Belloni , Greg Kroah-Hartman , Jiri Slaby , linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org, netdev@vger.kernel.org, linux-rtc@vger.kernel.org, linux-serial@vger.kernel.org Subject: [PATCH v11 net-next 1/2] MIPS: SGI-IP27: fix readb/writeb addressing Date: Fri, 13 Dec 2019 13:42:19 +0100 Message-Id: <20191213124221.25775-2-tbogendoerfer@suse.de> X-Mailer: git-send-email 2.24.0 In-Reply-To: <20191213124221.25775-1-tbogendoerfer@suse.de> References: <20191213124221.25775-1-tbogendoerfer@suse.de> MIME-Version: 1.0 Sender: linux-mips-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-mips@vger.kernel.org Our chosen byte swapping, which is what firmware already uses, is to do readl/writel by normal lw/sw intructions (data invariance). This also means we need to mangle addresses for u8 and u16 accesses. The mangling for 16bit has been done aready, but 8bit one was missing. Correcting this causes different addresses for accesses to the SuperIO and local bus of the IOC3 chip. This is fixed by changing byte order in ioc3 and m48rtc_rtc structs. Acked-by: Alexandre Belloni Signed-off-by: Thomas Bogendoerfer --- arch/mips/include/asm/mach-ip27/mangle-port.h | 4 +- arch/mips/include/asm/sn/ioc3.h | 38 +++++++++---------- drivers/net/ethernet/sgi/ioc3-eth.c | 12 ++++++ drivers/rtc/rtc-m48t35.c | 11 ++++++ 4 files changed, 44 insertions(+), 21 deletions(-) diff --git a/arch/mips/include/asm/mach-ip27/mangle-port.h b/arch/mips/include/asm/mach-ip27/mangle-port.h index f6e4912ea062..27c56efa519f 100644 --- a/arch/mips/include/asm/mach-ip27/mangle-port.h +++ b/arch/mips/include/asm/mach-ip27/mangle-port.h @@ -8,7 +8,7 @@ #ifndef __ASM_MACH_IP27_MANGLE_PORT_H #define __ASM_MACH_IP27_MANGLE_PORT_H -#define __swizzle_addr_b(port) (port) +#define __swizzle_addr_b(port) ((port) ^ 3) #define __swizzle_addr_w(port) ((port) ^ 2) #define __swizzle_addr_l(port) (port) #define __swizzle_addr_q(port) (port) @@ -20,6 +20,6 @@ # define ioswabl(a, x) (x) # define __mem_ioswabl(a, x) cpu_to_le32(x) # define ioswabq(a, x) (x) -# define __mem_ioswabq(a, x) cpu_to_le32(x) +# define __mem_ioswabq(a, x) cpu_to_le64(x) #endif /* __ASM_MACH_IP27_MANGLE_PORT_H */ diff --git a/arch/mips/include/asm/sn/ioc3.h b/arch/mips/include/asm/sn/ioc3.h index 78ef760ddde4..3865d3225780 100644 --- a/arch/mips/include/asm/sn/ioc3.h +++ b/arch/mips/include/asm/sn/ioc3.h @@ -21,50 +21,50 @@ struct ioc3_serialregs { /* SUPERIO uart register map */ struct ioc3_uartregs { + u8 iu_lcr; union { - u8 iu_rbr; /* read only, DLAB == 0 */ - u8 iu_thr; /* write only, DLAB == 0 */ - u8 iu_dll; /* DLAB == 1 */ + u8 iu_iir; /* read only */ + u8 iu_fcr; /* write only */ }; union { u8 iu_ier; /* DLAB == 0 */ u8 iu_dlm; /* DLAB == 1 */ }; union { - u8 iu_iir; /* read only */ - u8 iu_fcr; /* write only */ + u8 iu_rbr; /* read only, DLAB == 0 */ + u8 iu_thr; /* write only, DLAB == 0 */ + u8 iu_dll; /* DLAB == 1 */ }; - u8 iu_lcr; - u8 iu_mcr; - u8 iu_lsr; - u8 iu_msr; u8 iu_scr; + u8 iu_msr; + u8 iu_lsr; + u8 iu_mcr; }; struct ioc3_sioregs { u8 fill[0x141]; /* starts at 0x141 */ - u8 uartc; u8 kbdcg; + u8 uartc; - u8 fill0[0x150 - 0x142 - 1]; + u8 fill0[0x151 - 0x142 - 1]; - u8 pp_data; - u8 pp_dsr; u8 pp_dcr; + u8 pp_dsr; + u8 pp_data; - u8 fill1[0x158 - 0x152 - 1]; + u8 fill1[0x159 - 0x153 - 1]; - u8 pp_fifa; - u8 pp_cfgb; u8 pp_ecr; + u8 pp_cfgb; + u8 pp_fifa; - u8 fill2[0x168 - 0x15a - 1]; + u8 fill2[0x16a - 0x15b - 1]; - u8 rtcad; u8 rtcdat; + u8 rtcad; - u8 fill3[0x170 - 0x169 - 1]; + u8 fill3[0x170 - 0x16b - 1]; struct ioc3_uartregs uartb; /* 0x20170 */ struct ioc3_uartregs uarta; /* 0x20178 */ diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c index 06637b03deed..c180682e4df9 100644 --- a/drivers/net/ethernet/sgi/ioc3-eth.c +++ b/drivers/net/ethernet/sgi/ioc3-eth.c @@ -1079,6 +1079,16 @@ static int ioc3_is_menet(struct pci_dev *pdev) * Can't use UPF_IOREMAP as the whole of IOC3 resources have already been * registered. */ +static unsigned int ioc3_serial_in(struct uart_port *p, int offset) +{ + return readb(p->membase + (offset ^ 3)); +} + +static void ioc3_serial_out(struct uart_port *p, int offset, int value) +{ + writeb(value, p->membase + (offset ^ 3)); +} + static void ioc3_8250_register(struct ioc3_uartregs __iomem *uart) { #define COSMISC_CONSTANT 6 @@ -1093,6 +1103,8 @@ static void ioc3_8250_register(struct ioc3_uartregs __iomem *uart) .membase = (unsigned char __iomem *)uart, .mapbase = (unsigned long)uart, + .serial_in = ioc3_serial_in, + .serial_out = ioc3_serial_out, } }; unsigned char lcr; diff --git a/drivers/rtc/rtc-m48t35.c b/drivers/rtc/rtc-m48t35.c index d3a75d447fce..e8194f1f01a8 100644 --- a/drivers/rtc/rtc-m48t35.c +++ b/drivers/rtc/rtc-m48t35.c @@ -20,6 +20,16 @@ struct m48t35_rtc { u8 pad[0x7ff8]; /* starts at 0x7ff8 */ +#ifdef CONFIG_SGI_IP27 + u8 hour; + u8 min; + u8 sec; + u8 control; + u8 year; + u8 month; + u8 date; + u8 day; +#else u8 control; u8 sec; u8 min; @@ -28,6 +38,7 @@ struct m48t35_rtc { u8 date; u8 month; u8 year; +#endif }; #define M48T35_RTC_SET 0x80 From patchwork Fri Dec 13 12:42:20 2019 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Thomas Bogendoerfer X-Patchwork-Id: 11290485 Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id B3F6A188B for ; Fri, 13 Dec 2019 20:36:48 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [209.132.180.67]) by mail.kernel.org (Postfix) with ESMTP id 553F6246AE for ; Fri, 13 Dec 2019 20:36:48 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1727030AbfLMMnF (ORCPT ); Fri, 13 Dec 2019 07:43:05 -0500 Received: from mx2.suse.de ([195.135.220.15]:42740 "EHLO mx1.suse.de" rhost-flags-OK-OK-OK-FAIL) by vger.kernel.org with ESMTP id S1727077AbfLMMnE (ORCPT ); Fri, 13 Dec 2019 07:43:04 -0500 X-Virus-Scanned: by amavisd-new at test-mx.suse.de Received: from relay2.suse.de (unknown [195.135.220.254]) by mx1.suse.de (Postfix) with ESMTP id 6A99AB112; Fri, 13 Dec 2019 12:42:56 +0000 (UTC) From: Thomas Bogendoerfer To: Ralf Baechle , Paul Burton , James Hogan , Lee Jones , "David S. Miller" , Alessandro Zummo , Alexandre Belloni , Greg Kroah-Hartman , Jiri Slaby , linux-mips@vger.kernel.org, linux-kernel@vger.kernel.org, netdev@vger.kernel.org, linux-rtc@vger.kernel.org, linux-serial@vger.kernel.org Subject: [PATCH v11 net-next 2/2] mfd: ioc3: Add driver for SGI IOC3 chip Date: Fri, 13 Dec 2019 13:42:20 +0100 Message-Id: <20191213124221.25775-3-tbogendoerfer@suse.de> X-Mailer: git-send-email 2.24.0 In-Reply-To: <20191213124221.25775-1-tbogendoerfer@suse.de> References: <20191213124221.25775-1-tbogendoerfer@suse.de> MIME-Version: 1.0 Sender: linux-mips-owner@vger.kernel.org Precedence: bulk List-ID: X-Mailing-List: linux-mips@vger.kernel.org SGI IOC3 chip has integrated ethernet, keyboard and mouse interface. It also supports connecting a SuperIO chip for serial and parallel interfaces. IOC3 is used inside various SGI systemboards and add-on cards with different equipped external interfaces. Support for ethernet and serial interfaces were implemented inside the network driver. This patchset moves out the not network related parts to a new MFD driver, which takes care of card detection, setup of platform devices and interrupt distribution for the subdevices. Serial portion: Acked-by: Greg Kroah-Hartman Acked-for-MFD-by: Lee Jones Signed-off-by: Thomas Bogendoerfer Reviewed-by: Jakub Kicinski Acked-by: Linus Walleij --- arch/mips/sgi-ip27/ip27-timer.c | 20 - drivers/mfd/Kconfig | 13 + drivers/mfd/Makefile | 1 + drivers/mfd/ioc3.c | 700 ++++++++++++++++++++++++++++ drivers/net/ethernet/sgi/Kconfig | 5 +- drivers/net/ethernet/sgi/ioc3-eth.c | 556 ++++------------------ drivers/tty/serial/8250/8250_ioc3.c | 98 ++++ drivers/tty/serial/8250/Kconfig | 11 + drivers/tty/serial/8250/Makefile | 1 + 9 files changed, 924 insertions(+), 481 deletions(-) create mode 100644 drivers/mfd/ioc3.c create mode 100644 drivers/tty/serial/8250/8250_ioc3.c diff --git a/arch/mips/sgi-ip27/ip27-timer.c b/arch/mips/sgi-ip27/ip27-timer.c index 17302bbfa7a6..d53a29070e12 100644 --- a/arch/mips/sgi-ip27/ip27-timer.c +++ b/arch/mips/sgi-ip27/ip27-timer.c @@ -190,23 +190,3 @@ void hub_rtc_init(nasid_t nasid) LOCAL_HUB_S(PI_RT_PEND_B, 0); } } - -static int __init sgi_ip27_rtc_devinit(void) -{ - struct resource res; - - memset(&res, 0, sizeof(res)); - res.start = XPHYSADDR(KL_CONFIG_CH_CONS_INFO(master_nasid)->memory_base + - IOC3_BYTEBUS_DEV0); - res.end = res.start + 32767; - res.flags = IORESOURCE_MEM; - - return IS_ERR(platform_device_register_simple("rtc-m48t35", -1, - &res, 1)); -} - -/* - * kludge make this a device_initcall after ioc3 resource conflicts - * are resolved - */ -late_initcall(sgi_ip27_rtc_devinit); diff --git a/drivers/mfd/Kconfig b/drivers/mfd/Kconfig index 420900852166..7a4a41dddc97 100644 --- a/drivers/mfd/Kconfig +++ b/drivers/mfd/Kconfig @@ -2004,5 +2004,18 @@ config RAVE_SP_CORE Select this to get support for the Supervisory Processor device found on several devices in RAVE line of hardware. +config SGI_MFD_IOC3 + tristate "SGI IOC3 core driver" + depends on PCI && MIPS && 64BIT + select MFD_CORE + help + This option enables basic support for the SGI IOC3-based + controller cards. This option does not enable any specific + functions on such a card, but provides necessary infrastructure + for other drivers to utilize. + + If you have an SGI Origin, Octane, or a PCI IOC3 card, + then say Y. Otherwise say N. + endmenu endif diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile index aed99f08739f..5fe930c76ade 100644 --- a/drivers/mfd/Makefile +++ b/drivers/mfd/Makefile @@ -255,3 +255,4 @@ obj-$(CONFIG_MFD_ROHM_BD70528) += rohm-bd70528.o obj-$(CONFIG_MFD_ROHM_BD718XX) += rohm-bd718x7.o obj-$(CONFIG_MFD_STMFX) += stmfx.o +obj-$(CONFIG_SGI_MFD_IOC3) += ioc3.o diff --git a/drivers/mfd/ioc3.c b/drivers/mfd/ioc3.c new file mode 100644 index 000000000000..a905fddc0299 --- /dev/null +++ b/drivers/mfd/ioc3.c @@ -0,0 +1,700 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SGI IOC3 multifunction device driver + * + * Copyright (C) 2018, 2019 Thomas Bogendoerfer + * + * Based on work by: + * Stanislaw Skowronek + * Joshua Kinard + * Brent Casavant - IOC4 master driver + * Pat Gefre - IOC3 serial port IRQ demuxer + */ + +#include +#include +#include +#include +#include +#include +#include +#include +#include + +#include +#include + +#define IOC3_IRQ_SERIAL_A 6 +#define IOC3_IRQ_SERIAL_B 15 +#define IOC3_IRQ_KBD 22 +#define IOC3_IRQ_ETH_DOMAIN 23 + +/* Bitmask for selecting which IRQs are level triggered */ +#define IOC3_LVL_MASK (BIT(IOC3_IRQ_SERIAL_A) | BIT(IOC3_IRQ_SERIAL_B)) + +#define M48T35_REG_SIZE 32768 /* size of m48t35 registers */ + +/* 1.2 us latency timer (40 cycles at 33 MHz) */ +#define IOC3_LATENCY 40 + +struct ioc3_priv_data { + struct irq_domain *domain; + struct ioc3 __iomem *regs; + struct pci_dev *pdev; + int domain_irq; +}; + +static void ioc3_irq_ack(struct irq_data *d) +{ + struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d); + unsigned int hwirq = irqd_to_hwirq(d); + + writel(BIT(hwirq), &ipd->regs->sio_ir); +} + +static void ioc3_irq_mask(struct irq_data *d) +{ + struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d); + unsigned int hwirq = irqd_to_hwirq(d); + + writel(BIT(hwirq), &ipd->regs->sio_iec); +} + +static void ioc3_irq_unmask(struct irq_data *d) +{ + struct ioc3_priv_data *ipd = irq_data_get_irq_chip_data(d); + unsigned int hwirq = irqd_to_hwirq(d); + + writel(BIT(hwirq), &ipd->regs->sio_ies); +} + +static struct irq_chip ioc3_irq_chip = { + .name = "IOC3", + .irq_ack = ioc3_irq_ack, + .irq_mask = ioc3_irq_mask, + .irq_unmask = ioc3_irq_unmask, +}; + +static int ioc3_irq_domain_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hwirq) +{ + /* Set level IRQs for every interrupt contained in IOC3_LVL_MASK */ + if (BIT(hwirq) & IOC3_LVL_MASK) + irq_set_chip_and_handler(irq, &ioc3_irq_chip, handle_level_irq); + else + irq_set_chip_and_handler(irq, &ioc3_irq_chip, handle_edge_irq); + + irq_set_chip_data(irq, d->host_data); + return 0; +} + +static void ioc3_irq_domain_unmap(struct irq_domain *d, unsigned int irq) +{ + irq_set_chip_and_handler(irq, NULL, NULL); + irq_set_chip_data(irq, NULL); +} + +static const struct irq_domain_ops ioc3_irq_domain_ops = { + .map = ioc3_irq_domain_map, + .unmap = ioc3_irq_domain_unmap, +}; + +static void ioc3_irq_handler(struct irq_desc *desc) +{ + struct irq_domain *domain = irq_desc_get_handler_data(desc); + struct ioc3_priv_data *ipd = domain->host_data; + struct ioc3 __iomem *regs = ipd->regs; + u32 pending, mask; + unsigned int irq; + + pending = readl(®s->sio_ir); + mask = readl(®s->sio_ies); + pending &= mask; /* Mask off not enabled interrupts */ + + if (mask & BIT(IOC3_IRQ_ETH_DOMAIN)) + /* + * If ethernet interrupt is enabled we need to check + * ethernet registers for pending interrupts + */ + if (readl(®s->eth.eisr) & readl(®s->eth.eier)) + pending |= IOC3_IRQ_ETH_DOMAIN; + + if (pending) { + irq = irq_find_mapping(domain, __ffs(pending)); + if (irq) + generic_handle_irq(irq); + } else { + spurious_interrupt(); + } +} + +/* + * System boards/BaseIOs use more interrupt pins of the bridge ASIC + * to which the IOC3 is connected. Since the IOC3 MFD driver + * knows wiring of these extra pins, we use the map_irq function + * to get interrupts activated + */ +static int ioc3_map_irq(struct pci_dev *pdev, int pin) +{ + struct pci_host_bridge *hbrg = pci_find_host_bridge(pdev->bus); + + return hbrg->map_irq(pdev, pin, 0); +} + +static int ioc3_irq_domain_setup(struct ioc3_priv_data *ipd, int irq) +{ + struct irq_domain *domain; + struct fwnode_handle *fn; + + fn = irq_domain_alloc_named_fwnode("IOC3"); + if (!fn) + goto err; + + domain = irq_domain_create_linear(fn, 24, &ioc3_irq_domain_ops, ipd); + if (!domain) + goto err; + + irq_domain_free_fwnode(fn); + ipd->domain = domain; + + irq_set_chained_handler_and_data(irq, ioc3_irq_handler, domain); + ipd->domain_irq = irq; + return 0; + +err: + dev_err(&ipd->pdev->dev, "irq domain setup failed\n"); + return -ENOMEM; +} + +static struct resource ioc3_uarta_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, sregs.uarta), + sizeof_field(struct ioc3, sregs.uarta)), + DEFINE_RES_IRQ(IOC3_IRQ_SERIAL_A) +}; + +static struct resource ioc3_uartb_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, sregs.uartb), + sizeof_field(struct ioc3, sregs.uartb)), + DEFINE_RES_IRQ(IOC3_IRQ_SERIAL_B) +}; + +static struct mfd_cell ioc3_serial_cells[] = { + { + .name = "ioc3-serial8250", + .resources = ioc3_uarta_resources, + .num_resources = ARRAY_SIZE(ioc3_uarta_resources), + }, + { + .name = "ioc3-serial8250", + .resources = ioc3_uartb_resources, + .num_resources = ARRAY_SIZE(ioc3_uartb_resources), + } +}; + +static int ioc3_serial_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + /* Set gpio pins for RS232/RS422 mode selection */ + writel(GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL, + &ipd->regs->gpcr_s); + /* Select RS232 mode for uart a */ + writel(0, &ipd->regs->gppr[6]); + /* Select RS232 mode for uart b */ + writel(0, &ipd->regs->gppr[7]); + + /* Switch both ports to 16650 mode */ + writel(readl(&ipd->regs->port_a.sscr) & ~SSCR_DMA_EN, + &ipd->regs->port_a.sscr); + writel(readl(&ipd->regs->port_b.sscr) & ~SSCR_DMA_EN, + &ipd->regs->port_b.sscr); + udelay(1000); /* Wait until mode switch is done */ + + ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO, + ioc3_serial_cells, ARRAY_SIZE(ioc3_serial_cells), + &ipd->pdev->resource[0], 0, ipd->domain); + if (ret) { + dev_err(&ipd->pdev->dev, "Failed to add 16550 subdevs\n"); + return ret; + } + + return 0; +} + +static struct resource ioc3_kbd_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, serio), + sizeof_field(struct ioc3, serio)), + DEFINE_RES_IRQ(IOC3_IRQ_KBD) +}; + +static struct mfd_cell ioc3_kbd_cells[] = { + { + .name = "ioc3-kbd", + .resources = ioc3_kbd_resources, + .num_resources = ARRAY_SIZE(ioc3_kbd_resources), + } +}; + +static int ioc3_kbd_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO, + ioc3_kbd_cells, ARRAY_SIZE(ioc3_kbd_cells), + &ipd->pdev->resource[0], 0, ipd->domain); + if (ret) { + dev_err(&ipd->pdev->dev, "Failed to add 16550 subdevs\n"); + return ret; + } + + return 0; +} + +static struct resource ioc3_eth_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, eth), + sizeof_field(struct ioc3, eth)), + DEFINE_RES_MEM(offsetof(struct ioc3, ssram), + sizeof_field(struct ioc3, ssram)), + DEFINE_RES_IRQ(0) +}; + +static struct resource ioc3_w1_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, mcr), + sizeof_field(struct ioc3, mcr)), +}; +static struct sgi_w1_platform_data ioc3_w1_platform_data; + +static struct mfd_cell ioc3_eth_cells[] = { + { + .name = "ioc3-eth", + .resources = ioc3_eth_resources, + .num_resources = ARRAY_SIZE(ioc3_eth_resources), + }, + { + .name = "sgi_w1", + .resources = ioc3_w1_resources, + .num_resources = ARRAY_SIZE(ioc3_w1_resources), + .platform_data = &ioc3_w1_platform_data, + .pdata_size = sizeof(ioc3_w1_platform_data), + } +}; + +static int ioc3_eth_setup(struct ioc3_priv_data *ipd, bool use_domain) +{ + int irq = ipd->pdev->irq; + int ret; + + /* Enable One-Wire bus */ + writel(GPCR_MLAN_EN, &ipd->regs->gpcr_s); + + /* Generate unique identifier */ + snprintf(ioc3_w1_platform_data.dev_id, + sizeof(ioc3_w1_platform_data.dev_id), "ioc3-%012llx", + ipd->pdev->resource->start); + + if (use_domain) + irq = irq_create_mapping(ipd->domain, IOC3_IRQ_ETH_DOMAIN); + + ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO, + ioc3_eth_cells, ARRAY_SIZE(ioc3_eth_cells), + &ipd->pdev->resource[0], irq, NULL); + if (ret) { + dev_err(&ipd->pdev->dev, "Failed to add ETH/W1 subdev\n"); + return ret; + } + + return 0; +} + +static struct resource ioc3_m48t35_resources[] = { + DEFINE_RES_MEM(IOC3_BYTEBUS_DEV0, M48T35_REG_SIZE) +}; + +static struct mfd_cell ioc3_m48t35_cells[] = { + { + .name = "rtc-m48t35", + .resources = ioc3_m48t35_resources, + .num_resources = ARRAY_SIZE(ioc3_m48t35_resources), + } +}; + +static int ioc3_m48t35_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + ret = mfd_add_devices(&ipd->pdev->dev, PLATFORM_DEVID_AUTO, + ioc3_m48t35_cells, ARRAY_SIZE(ioc3_m48t35_cells), + &ipd->pdev->resource[0], 0, ipd->domain); + if (ret) + dev_err(&ipd->pdev->dev, "Failed to add M48T35 subdev\n"); + + return ret; +} + +static struct ds1685_rtc_platform_data ip30_rtc_platform_data = { + .bcd_mode = false, + .no_irq = false, + .uie_unsupported = true, + .access_type = ds1685_reg_indirect, +}; + +static struct resource ioc3_rtc_ds1685_resources[] = { + DEFINE_RES_MEM(IOC3_BYTEBUS_DEV1, 1), + DEFINE_RES_MEM(IOC3_BYTEBUS_DEV2, 1), + DEFINE_RES_IRQ(0) +}; + +static struct mfd_cell ioc3_ds1685_cells[] = { + { + .name = "rtc-ds1685", + .resources = ioc3_rtc_ds1685_resources, + .num_resources = ARRAY_SIZE(ioc3_rtc_ds1685_resources), + .platform_data = &ip30_rtc_platform_data, + .pdata_size = sizeof(ip30_rtc_platform_data), + .id = PLATFORM_DEVID_NONE, + } +}; + +static int ioc3_ds1685_setup(struct ioc3_priv_data *ipd) +{ + int ret, irq; + + irq = ioc3_map_irq(ipd->pdev, 6); + + ret = mfd_add_devices(&ipd->pdev->dev, 0, ioc3_ds1685_cells, + ARRAY_SIZE(ioc3_ds1685_cells), + &ipd->pdev->resource[0], irq, NULL); + if (ret) + dev_err(&ipd->pdev->dev, "Failed to add DS1685 subdev\n"); + + return ret; +}; + + +static struct resource ioc3_leds_resources[] = { + DEFINE_RES_MEM(offsetof(struct ioc3, gppr[0]), + sizeof_field(struct ioc3, gppr[0])), + DEFINE_RES_MEM(offsetof(struct ioc3, gppr[1]), + sizeof_field(struct ioc3, gppr[1])), +}; + +static struct mfd_cell ioc3_led_cells[] = { + { + .name = "ip30-leds", + .resources = ioc3_leds_resources, + .num_resources = ARRAY_SIZE(ioc3_leds_resources), + .id = PLATFORM_DEVID_NONE, + } +}; + +static int ioc3_led_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + ret = mfd_add_devices(&ipd->pdev->dev, 0, ioc3_led_cells, + ARRAY_SIZE(ioc3_led_cells), + &ipd->pdev->resource[0], 0, ipd->domain); + if (ret) + dev_err(&ipd->pdev->dev, "Failed to add LED subdev\n"); + + return ret; +} + +static int ip27_baseio_setup(struct ioc3_priv_data *ipd) +{ + int ret, io_irq; + + io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 2); + ret = ioc3_irq_domain_setup(ipd, io_irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, false); + if (ret) + return ret; + + ret = ioc3_serial_setup(ipd); + if (ret) + return ret; + + return ioc3_m48t35_setup(ipd); +} + +static int ip27_baseio6g_setup(struct ioc3_priv_data *ipd) +{ + int ret, io_irq; + + io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 2); + ret = ioc3_irq_domain_setup(ipd, io_irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, false); + if (ret) + return ret; + + ret = ioc3_serial_setup(ipd); + if (ret) + return ret; + + ret = ioc3_m48t35_setup(ipd); + if (ret) + return ret; + + return ioc3_kbd_setup(ipd); +} + +static int ip27_mio_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + ret = ioc3_irq_domain_setup(ipd, ipd->pdev->irq); + if (ret) + return ret; + + ret = ioc3_serial_setup(ipd); + if (ret) + return ret; + + return ioc3_kbd_setup(ipd); +} + +static int ip29_sysboard_setup(struct ioc3_priv_data *ipd) +{ + int ret, io_irq; + + io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 1); + ret = ioc3_irq_domain_setup(ipd, io_irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, false); + if (ret) + return ret; + + ret = ioc3_serial_setup(ipd); + if (ret) + return ret; + + ret = ioc3_m48t35_setup(ipd); + if (ret) + return ret; + + return ioc3_kbd_setup(ipd); +} + +static int ip30_sysboard_setup(struct ioc3_priv_data *ipd) +{ + int ret, io_irq; + + io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 2); + ret = ioc3_irq_domain_setup(ipd, io_irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, false); + if (ret) + return ret; + + ret = ioc3_serial_setup(ipd); + if (ret) + return ret; + + ret = ioc3_kbd_setup(ipd); + if (ret) + return ret; + + ret = ioc3_ds1685_setup(ipd); + if (ret) + return ret; + + return ioc3_led_setup(ipd); +} + +static int ioc3_menet_setup(struct ioc3_priv_data *ipd) +{ + int ret, io_irq; + + io_irq = ioc3_map_irq(ipd->pdev, PCI_SLOT(ipd->pdev->devfn) + 4); + ret = ioc3_irq_domain_setup(ipd, io_irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, false); + if (ret) + return ret; + + return ioc3_serial_setup(ipd); +} + +static int ioc3_menet4_setup(struct ioc3_priv_data *ipd) +{ + return ioc3_eth_setup(ipd, false); +} + +static int ioc3_cad_duo_setup(struct ioc3_priv_data *ipd) +{ + int ret; + + ret = ioc3_irq_domain_setup(ipd, ipd->pdev->irq); + if (ret) + return ret; + + ret = ioc3_eth_setup(ipd, true); + if (ret) + return ret; + + return ioc3_kbd_setup(ipd); +} + +/* Helper macro for filling ioc3_info array */ +#define IOC3_SID(_name, _sid, _setup) \ + { \ + .name = _name, \ + .sid = PCI_VENDOR_ID_SGI | (IOC3_SUBSYS_ ## _sid << 16), \ + .setup = _setup, \ + } + +static struct { + const char *name; + u32 sid; + int (*setup)(struct ioc3_priv_data *ipd); +} ioc3_infos[] = { + IOC3_SID("IP27 BaseIO6G", IP27_BASEIO6G, &ip27_baseio6g_setup), + IOC3_SID("IP27 MIO", IP27_MIO, &ip27_mio_setup), + IOC3_SID("IP27 BaseIO", IP27_BASEIO, &ip27_baseio_setup), + IOC3_SID("IP29 System Board", IP29_SYSBOARD, &ip29_sysboard_setup), + IOC3_SID("IP30 System Board", IP30_SYSBOARD, &ip30_sysboard_setup), + IOC3_SID("MENET", MENET, &ioc3_menet_setup), + IOC3_SID("MENET4", MENET4, &ioc3_menet4_setup) +}; +#undef IOC3_SID + +static int ioc3_setup(struct ioc3_priv_data *ipd) +{ + u32 sid; + int i; + + /* Clear IRQs */ + writel(~0, &ipd->regs->sio_iec); + writel(~0, &ipd->regs->sio_ir); + writel(0, &ipd->regs->eth.eier); + writel(~0, &ipd->regs->eth.eisr); + + /* Read subsystem vendor id and subsystem id */ + pci_read_config_dword(ipd->pdev, PCI_SUBSYSTEM_VENDOR_ID, &sid); + + for (i = 0; i < ARRAY_SIZE(ioc3_infos); i++) + if (sid == ioc3_infos[i].sid) { + pr_info("ioc3: %s\n", ioc3_infos[i].name); + return ioc3_infos[i].setup(ipd); + } + + /* Treat everything not identified by PCI subid as CAD DUO */ + pr_info("ioc3: CAD DUO\n"); + return ioc3_cad_duo_setup(ipd); +} + +static int ioc3_mfd_probe(struct pci_dev *pdev, + const struct pci_device_id *pci_id) +{ + struct ioc3_priv_data *ipd; + struct ioc3 __iomem *regs; + int ret; + + ret = pci_enable_device(pdev); + if (ret) + return ret; + + pci_write_config_byte(pdev, PCI_LATENCY_TIMER, IOC3_LATENCY); + pci_set_master(pdev); + + ret = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); + if (ret) { + pr_err("%s: No usable DMA configuration, aborting.\n", + pci_name(pdev)); + goto out_disable_device; + } + + /* Set up per-IOC3 data */ + ipd = devm_kzalloc(&pdev->dev, sizeof(struct ioc3_priv_data), + GFP_KERNEL); + if (!ipd) { + ret = -ENOMEM; + goto out_disable_device; + } + ipd->pdev = pdev; + + /* + * Map all IOC3 registers. These are shared between subdevices + * so the main IOC3 module manages them. + */ + regs = pci_ioremap_bar(pdev, 0); + if (!regs) { + dev_warn(&pdev->dev, "ioc3: Unable to remap PCI BAR for %s.\n", + pci_name(pdev)); + ret = -ENOMEM; + goto out_disable_device; + } + ipd->regs = regs; + + /* Track PCI-device specific data */ + pci_set_drvdata(pdev, ipd); + + ret = ioc3_setup(ipd); + if (ret) { + /* Remove all already added MFD devices */ + mfd_remove_devices(&ipd->pdev->dev); + if (ipd->domain) { + irq_domain_remove(ipd->domain); + free_irq(ipd->domain_irq, (void *)ipd); + } + pci_iounmap(pdev, regs); + goto out_disable_device; + } + + return 0; + +out_disable_device: + pci_disable_device(pdev); + return ret; +} + +static void ioc3_mfd_remove(struct pci_dev *pdev) +{ + struct ioc3_priv_data *ipd; + + ipd = pci_get_drvdata(pdev); + + /* Clear and disable all IRQs */ + writel(~0, &ipd->regs->sio_iec); + writel(~0, &ipd->regs->sio_ir); + + /* Release resources */ + mfd_remove_devices(&ipd->pdev->dev); + if (ipd->domain) { + irq_domain_remove(ipd->domain); + free_irq(ipd->domain_irq, (void *)ipd); + } + pci_iounmap(pdev, ipd->regs); + pci_disable_device(pdev); +} + +static struct pci_device_id ioc3_mfd_id_table[] = { + { PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3, PCI_ANY_ID, PCI_ANY_ID }, + { 0, }, +}; +MODULE_DEVICE_TABLE(pci, ioc3_mfd_id_table); + +static struct pci_driver ioc3_mfd_driver = { + .name = "IOC3", + .id_table = ioc3_mfd_id_table, + .probe = ioc3_mfd_probe, + .remove = ioc3_mfd_remove, +}; + +module_pci_driver(ioc3_mfd_driver); + +MODULE_AUTHOR("Thomas Bogendoerfer "); +MODULE_DESCRIPTION("SGI IOC3 MFD driver"); +MODULE_LICENSE("GPL v2"); diff --git a/drivers/net/ethernet/sgi/Kconfig b/drivers/net/ethernet/sgi/Kconfig index 37f048e1230c..bc26fa0d196f 100644 --- a/drivers/net/ethernet/sgi/Kconfig +++ b/drivers/net/ethernet/sgi/Kconfig @@ -6,7 +6,7 @@ config NET_VENDOR_SGI bool "SGI devices" default y - depends on (PCI && SGI_IP27) || SGI_IP32 + depends on (PCI && SGI_MFD_IOC3) || SGI_IP32 ---help--- If you have a network (Ethernet) card belonging to this class, say Y. @@ -19,7 +19,8 @@ if NET_VENDOR_SGI config SGI_IOC3_ETH bool "SGI IOC3 Ethernet" - depends on PCI && SGI_IP27 + depends on PCI && SGI_MFD_IOC3 + select CRC16 select CRC32 select MII ---help--- diff --git a/drivers/net/ethernet/sgi/ioc3-eth.c b/drivers/net/ethernet/sgi/ioc3-eth.c index c180682e4df9..e61eb891c0f7 100644 --- a/drivers/net/ethernet/sgi/ioc3-eth.c +++ b/drivers/net/ethernet/sgi/ioc3-eth.c @@ -14,7 +14,6 @@ * o Use prefetching for large packets. What is a good lower limit for * prefetching? * o Use hardware checksums. - * o Convert to using a IOC3 meta driver. * o Which PHYs might possibly be attached to the IOC3 in real live, * which workarounds are required for them? Do we ever have Lucent's? * o For the 2.5 branch kill the mii-tool ioctls. @@ -28,7 +27,8 @@ #include #include #include -#include +#include +#include #include #include #include @@ -37,28 +37,22 @@ #include #include #include - -#ifdef CONFIG_SERIAL_8250 -#include -#include -#include -#endif - #include #include #include #include #include +#include +#include #include -#include -#include -#include -#include #include #include +#define CRC16_INIT 0 +#define CRC16_VALID 0xb001 + /* Number of RX buffers. This is tunable in the range of 16 <= x < 512. * The value must be a power of two. */ @@ -85,7 +79,6 @@ /* Private per NIC data of the driver. */ struct ioc3_private { struct ioc3_ethregs *regs; - struct ioc3 *all_regs; struct device *dma_dev; u32 *ssram; unsigned long *rxr; /* pointer to receiver ring */ @@ -104,9 +97,6 @@ struct ioc3_private { spinlock_t ioc3_lock; struct mii_if_info mii; - struct net_device *dev; - struct pci_dev *pdev; - /* Members used by autonegotiation */ struct timer_list ioc3_timer; }; @@ -123,10 +113,8 @@ static int ioc3_alloc_rx_bufs(struct net_device *dev); static void ioc3_free_rx_bufs(struct ioc3_private *ip); static inline void ioc3_clean_tx_ring(struct ioc3_private *ip); -static const char ioc3_str[] = "IOC3 Ethernet"; static const struct ethtool_ops ioc3_ethtool_ops; - static inline unsigned long aligned_rx_skb_addr(unsigned long addr) { return (~addr + 1) & (IOC3_DMA_XFER_LEN - 1UL); @@ -179,225 +167,61 @@ static inline unsigned long ioc3_map(dma_addr_t addr, unsigned long attr) #define ERBAR_VAL 0 #endif -#define IOC3_SIZE 0x100000 - -static inline u32 mcr_pack(u32 pulse, u32 sample) -{ - return (pulse << 10) | (sample << 2); -} - -static int nic_wait(u32 __iomem *mcr) -{ - u32 m; - - do { - m = readl(mcr); - } while (!(m & 2)); - - return m & 1; -} - -static int nic_reset(u32 __iomem *mcr) -{ - int presence; - - writel(mcr_pack(500, 65), mcr); - presence = nic_wait(mcr); - - writel(mcr_pack(0, 500), mcr); - nic_wait(mcr); - - return presence; -} - -static inline int nic_read_bit(u32 __iomem *mcr) -{ - int result; - - writel(mcr_pack(6, 13), mcr); - result = nic_wait(mcr); - writel(mcr_pack(0, 100), mcr); - nic_wait(mcr); - - return result; -} - -static inline void nic_write_bit(u32 __iomem *mcr, int bit) -{ - if (bit) - writel(mcr_pack(6, 110), mcr); - else - writel(mcr_pack(80, 30), mcr); - - nic_wait(mcr); -} - -/* Read a byte from an iButton device - */ -static u32 nic_read_byte(u32 __iomem *mcr) -{ - u32 result = 0; - int i; - - for (i = 0; i < 8; i++) - result = (result >> 1) | (nic_read_bit(mcr) << 7); - - return result; -} - -/* Write a byte to an iButton device - */ -static void nic_write_byte(u32 __iomem *mcr, int byte) +static int ioc3eth_nvmem_match(struct device *dev, const void *data) { - int i, bit; - - for (i = 8; i; i--) { - bit = byte & 1; - byte >>= 1; - - nic_write_bit(mcr, bit); - } -} + const char *name = dev_name(dev); + const char *prefix = data; + int prefix_len; -static u64 nic_find(u32 __iomem *mcr, int *last) -{ - int a, b, index, disc; - u64 address = 0; - - nic_reset(mcr); - /* Search ROM. */ - nic_write_byte(mcr, 0xf0); - - /* Algorithm from ``Book of iButton Standards''. */ - for (index = 0, disc = 0; index < 64; index++) { - a = nic_read_bit(mcr); - b = nic_read_bit(mcr); - - if (a && b) { - pr_warn("NIC search failed (not fatal).\n"); - *last = 0; - return 0; - } + prefix_len = strlen(prefix); + if (strlen(name) < (prefix_len + 3)) + return 0; - if (!a && !b) { - if (index == *last) { - address |= 1UL << index; - } else if (index > *last) { - address &= ~(1UL << index); - disc = index; - } else if ((address & (1UL << index)) == 0) { - disc = index; - } - nic_write_bit(mcr, address & (1UL << index)); - continue; - } else { - if (a) - address |= 1UL << index; - else - address &= ~(1UL << index); - nic_write_bit(mcr, a); - continue; - } - } - - *last = disc; - - return address; -} - -static int nic_init(u32 __iomem *mcr) -{ - const char *unknown = "unknown"; - const char *type = unknown; - u8 crc; - u8 serial[6]; - int save = 0, i; - - while (1) { - u64 reg; - - reg = nic_find(mcr, &save); - - switch (reg & 0xff) { - case 0x91: - type = "DS1981U"; - break; - default: - if (save == 0) { - /* Let the caller try again. */ - return -1; - } - continue; - } + if (memcmp(prefix, name, prefix_len) != 0) + return 0; - nic_reset(mcr); - - /* Match ROM. */ - nic_write_byte(mcr, 0x55); - for (i = 0; i < 8; i++) - nic_write_byte(mcr, (reg >> (i << 3)) & 0xff); - - reg >>= 8; /* Shift out type. */ - for (i = 0; i < 6; i++) { - serial[i] = reg & 0xff; - reg >>= 8; - } - crc = reg & 0xff; - break; - } - - pr_info("Found %s NIC", type); - if (type != unknown) - pr_cont(" registration number %pM, CRC %02x", serial, crc); - pr_cont(".\n"); + /* found nvmem device which is attached to our ioc3 + * now check for one wire family code 09, 89 and 91 + */ + if (memcmp(name + prefix_len, "09-", 3) == 0) + return 1; + if (memcmp(name + prefix_len, "89-", 3) == 0) + return 1; + if (memcmp(name + prefix_len, "91-", 3) == 0) + return 1; return 0; } -/* Read the NIC (Number-In-a-Can) device used to store the MAC address on - * SN0 / SN00 nodeboards and PCI cards. - */ -static void ioc3_get_eaddr_nic(struct ioc3_private *ip) +static int ioc3eth_get_mac_addr(struct resource *res, u8 mac_addr[6]) { - u32 __iomem *mcr = &ip->all_regs->mcr; - int tries = 2; /* There may be some problem with the battery? */ - u8 nic[14]; + struct nvmem_device *nvmem; + char prefix[24]; + u8 prom[16]; + int ret; int i; - writel(1 << 21, &ip->all_regs->gpcr_s); - - while (tries--) { - if (!nic_init(mcr)) - break; - udelay(500); - } - - if (tries < 0) { - pr_err("Failed to read MAC address\n"); - return; - } + snprintf(prefix, sizeof(prefix), "ioc3-%012llx-", + res->start & ~0xffff); - /* Read Memory. */ - nic_write_byte(mcr, 0xf0); - nic_write_byte(mcr, 0x00); - nic_write_byte(mcr, 0x00); + nvmem = nvmem_device_find(prefix, ioc3eth_nvmem_match); + if (IS_ERR(nvmem)) + return PTR_ERR(nvmem); - for (i = 13; i >= 0; i--) - nic[i] = nic_read_byte(mcr); + ret = nvmem_device_read(nvmem, 0, 16, prom); + nvmem_device_put(nvmem); + if (ret < 0) + return ret; - for (i = 2; i < 8; i++) - ip->dev->dev_addr[i - 2] = nic[i]; -} + /* check, if content is valid */ + if (prom[0] != 0x0a || + crc16(CRC16_INIT, prom, 13) != CRC16_VALID) + return -EINVAL; -/* Ok, this is hosed by design. It's necessary to know what machine the - * NIC is in in order to know how to read the NIC address. We also have - * to know if it's a PCI card or a NIC in on the node board ... - */ -static void ioc3_get_eaddr(struct ioc3_private *ip) -{ - ioc3_get_eaddr_nic(ip); + for (i = 0; i < 6; i++) + mac_addr[i] = prom[10 - i]; - pr_info("Ethernet address is %pM.\n", ip->dev->dev_addr); + return 0; } static void __ioc3_set_mac_address(struct net_device *dev) @@ -770,7 +594,7 @@ static int ioc3_mii_init(struct ioc3_private *ip) u16 word; for (i = 0; i < 32; i++) { - word = ioc3_mdio_read(ip->dev, i, MII_PHYSID1); + word = ioc3_mdio_read(ip->mii.dev, i, MII_PHYSID1); if (word != 0xffff && word != 0x0000) { found = 1; @@ -975,12 +799,6 @@ static int ioc3_open(struct net_device *dev) { struct ioc3_private *ip = netdev_priv(dev); - if (request_irq(dev->irq, ioc3_interrupt, IRQF_SHARED, ioc3_str, dev)) { - netdev_err(dev, "Can't get irq %d\n", dev->irq); - - return -EAGAIN; - } - ip->ehar_h = 0; ip->ehar_l = 0; @@ -1013,159 +831,6 @@ static int ioc3_close(struct net_device *dev) return 0; } -/* MENET cards have four IOC3 chips, which are attached to two sets of - * PCI slot resources each: the primary connections are on slots - * 0..3 and the secondaries are on 4..7 - * - * All four ethernets are brought out to connectors; six serial ports - * (a pair from each of the first three IOC3s) are brought out to - * MiniDINs; all other subdevices are left swinging in the wind, leave - * them disabled. - */ - -static int ioc3_adjacent_is_ioc3(struct pci_dev *pdev, int slot) -{ - struct pci_dev *dev = pci_get_slot(pdev->bus, PCI_DEVFN(slot, 0)); - int ret = 0; - - if (dev) { - if (dev->vendor == PCI_VENDOR_ID_SGI && - dev->device == PCI_DEVICE_ID_SGI_IOC3) - ret = 1; - pci_dev_put(dev); - } - - return ret; -} - -static int ioc3_is_menet(struct pci_dev *pdev) -{ - return !pdev->bus->parent && - ioc3_adjacent_is_ioc3(pdev, 0) && - ioc3_adjacent_is_ioc3(pdev, 1) && - ioc3_adjacent_is_ioc3(pdev, 2); -} - -#ifdef CONFIG_SERIAL_8250 -/* Note about serial ports and consoles: - * For console output, everyone uses the IOC3 UARTA (offset 0x178) - * connected to the master node (look in ip27_setup_console() and - * ip27prom_console_write()). - * - * For serial (/dev/ttyS0 etc), we can not have hardcoded serial port - * addresses on a partitioned machine. Since we currently use the ioc3 - * serial ports, we use dynamic serial port discovery that the serial.c - * driver uses for pci/pnp ports (there is an entry for the SGI ioc3 - * boards in pci_boards[]). Unfortunately, UARTA's pio address is greater - * than UARTB's, although UARTA on o200s has traditionally been known as - * port 0. So, we just use one serial port from each ioc3 (since the - * serial driver adds addresses to get to higher ports). - * - * The first one to do a register_console becomes the preferred console - * (if there is no kernel command line console= directive). /dev/console - * (ie 5, 1) is then "aliased" into the device number returned by the - * "device" routine referred to in this console structure - * (ip27prom_console_dev). - * - * Also look in ip27-pci.c:pci_fixup_ioc3() for some comments on working - * around ioc3 oddities in this respect. - * - * The IOC3 serials use a 22MHz clock rate with an additional divider which - * can be programmed in the SCR register if the DLAB bit is set. - * - * Register to interrupt zero because we share the interrupt with - * the serial driver which we don't properly support yet. - * - * Can't use UPF_IOREMAP as the whole of IOC3 resources have already been - * registered. - */ -static unsigned int ioc3_serial_in(struct uart_port *p, int offset) -{ - return readb(p->membase + (offset ^ 3)); -} - -static void ioc3_serial_out(struct uart_port *p, int offset, int value) -{ - writeb(value, p->membase + (offset ^ 3)); -} - -static void ioc3_8250_register(struct ioc3_uartregs __iomem *uart) -{ -#define COSMISC_CONSTANT 6 - - struct uart_8250_port port = { - .port = { - .irq = 0, - .flags = UPF_SKIP_TEST | UPF_BOOT_AUTOCONF, - .iotype = UPIO_MEM, - .regshift = 0, - .uartclk = (22000000 << 1) / COSMISC_CONSTANT, - - .membase = (unsigned char __iomem *)uart, - .mapbase = (unsigned long)uart, - .serial_in = ioc3_serial_in, - .serial_out = ioc3_serial_out, - } - }; - unsigned char lcr; - - lcr = readb(&uart->iu_lcr); - writeb(lcr | UART_LCR_DLAB, &uart->iu_lcr); - writeb(COSMISC_CONSTANT, &uart->iu_scr); - writeb(lcr, &uart->iu_lcr); - readb(&uart->iu_lcr); - serial8250_register_8250_port(&port); -} - -static void ioc3_serial_probe(struct pci_dev *pdev, struct ioc3 *ioc3) -{ - u32 sio_iec; - - /* We need to recognice and treat the fourth MENET serial as it - * does not have an SuperIO chip attached to it, therefore attempting - * to access it will result in bus errors. We call something an - * MENET if PCI slot 0, 1, 2 and 3 of a master PCI bus all have an IOC3 - * in it. This is paranoid but we want to avoid blowing up on a - * showhorn PCI box that happens to have 4 IOC3 cards in it so it's - * not paranoid enough ... - */ - if (ioc3_is_menet(pdev) && PCI_SLOT(pdev->devfn) == 3) - return; - - /* Switch IOC3 to PIO mode. It probably already was but let's be - * paranoid - */ - writel(GPCR_UARTA_MODESEL | GPCR_UARTB_MODESEL, &ioc3->gpcr_s); - readl(&ioc3->gpcr_s); - writel(0, &ioc3->gppr[6]); - readl(&ioc3->gppr[6]); - writel(0, &ioc3->gppr[7]); - readl(&ioc3->gppr[7]); - writel(readl(&ioc3->port_a.sscr) & ~SSCR_DMA_EN, &ioc3->port_a.sscr); - readl(&ioc3->port_a.sscr); - writel(readl(&ioc3->port_b.sscr) & ~SSCR_DMA_EN, &ioc3->port_b.sscr); - readl(&ioc3->port_b.sscr); - /* Disable all SA/B interrupts except for SA/B_INT in SIO_IEC. */ - sio_iec = readl(&ioc3->sio_iec); - sio_iec &= ~(SIO_IR_SA_TX_MT | SIO_IR_SA_RX_FULL | - SIO_IR_SA_RX_HIGH | SIO_IR_SA_RX_TIMER | - SIO_IR_SA_DELTA_DCD | SIO_IR_SA_DELTA_CTS | - SIO_IR_SA_TX_EXPLICIT | SIO_IR_SA_MEMERR); - sio_iec |= SIO_IR_SA_INT; - sio_iec &= ~(SIO_IR_SB_TX_MT | SIO_IR_SB_RX_FULL | - SIO_IR_SB_RX_HIGH | SIO_IR_SB_RX_TIMER | - SIO_IR_SB_DELTA_DCD | SIO_IR_SB_DELTA_CTS | - SIO_IR_SB_TX_EXPLICIT | SIO_IR_SB_MEMERR); - sio_iec |= SIO_IR_SB_INT; - writel(sio_iec, &ioc3->sio_iec); - writel(0, &ioc3->port_a.sscr); - writel(0, &ioc3->port_b.sscr); - - ioc3_8250_register(&ioc3->sregs.uarta); - ioc3_8250_register(&ioc3->sregs.uartb); -} -#endif - static const struct net_device_ops ioc3_netdev_ops = { .ndo_open = ioc3_open, .ndo_stop = ioc3_close, @@ -1178,61 +843,52 @@ static const struct net_device_ops ioc3_netdev_ops = { .ndo_set_mac_address = ioc3_set_mac_address, }; -static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) +static int ioc3eth_probe(struct platform_device *pdev) { - unsigned int sw_physid1, sw_physid2; - struct net_device *dev = NULL; + u32 sw_physid1, sw_physid2, vendor, model, rev; struct ioc3_private *ip; - struct ioc3 *ioc3; - unsigned long ioc3_base, ioc3_size; - u32 vendor, model, rev; + struct net_device *dev; + struct resource *regs; + u8 mac_addr[6]; int err; - /* Configure DMA attributes. */ - err = dma_set_mask_and_coherent(&pdev->dev, DMA_BIT_MASK(64)); - if (err) { - pr_err("%s: No usable DMA configuration, aborting.\n", - pci_name(pdev)); - goto out; - } - - if (pci_enable_device(pdev)) - return -ENODEV; + regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + /* get mac addr from one wire prom */ + if (ioc3eth_get_mac_addr(regs, mac_addr)) + return -EPROBE_DEFER; /* not available yet */ dev = alloc_etherdev(sizeof(struct ioc3_private)); - if (!dev) { - err = -ENOMEM; - goto out_disable; - } - - err = pci_request_regions(pdev, "ioc3"); - if (err) - goto out_free; + if (!dev) + return -ENOMEM; SET_NETDEV_DEV(dev, &pdev->dev); ip = netdev_priv(dev); - ip->dev = dev; - ip->dma_dev = &pdev->dev; - - dev->irq = pdev->irq; + ip->dma_dev = pdev->dev.parent; + ip->regs = devm_platform_ioremap_resource(pdev, 0); + if (!ip->regs) { + err = -ENOMEM; + goto out_free; + } - ioc3_base = pci_resource_start(pdev, 0); - ioc3_size = pci_resource_len(pdev, 0); - ioc3 = (struct ioc3 *)ioremap(ioc3_base, ioc3_size); - if (!ioc3) { - pr_err("ioc3eth(%s): ioremap failed, goodbye.\n", - pci_name(pdev)); + ip->ssram = devm_platform_ioremap_resource(pdev, 1); + if (!ip->ssram) { err = -ENOMEM; - goto out_res; + goto out_free; } - ip->regs = &ioc3->eth; - ip->ssram = ioc3->ssram; - ip->all_regs = ioc3; -#ifdef CONFIG_SERIAL_8250 - ioc3_serial_probe(pdev, ioc3); -#endif + dev->irq = platform_get_irq(pdev, 0); + if (dev->irq < 0) { + err = dev->irq; + goto out_free; + } + + if (devm_request_irq(&pdev->dev, dev->irq, ioc3_interrupt, + IRQF_SHARED, "ioc3-eth", dev)) { + dev_err(&pdev->dev, "Can't get irq %d\n", dev->irq); + err = -ENODEV; + goto out_free; + } spin_lock_init(&ip->ioc3_lock); timer_setup(&ip->ioc3_timer, ioc3_timer, 0); @@ -1262,8 +918,6 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) ioc3_init(dev); - ip->pdev = pdev; - ip->mii.phy_id_mask = 0x1f; ip->mii.reg_num_mask = 0x1f; ip->mii.dev = dev; @@ -1273,15 +927,14 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) ioc3_mii_init(ip); if (ip->mii.phy_id == -1) { - pr_err("ioc3-eth(%s): Didn't find a PHY, goodbye.\n", - pci_name(pdev)); + netdev_err(dev, "Didn't find a PHY, goodbye.\n"); err = -ENODEV; goto out_stop; } ioc3_mii_start(ip); ioc3_ssram_disc(ip); - ioc3_get_eaddr(ip); + memcpy(dev->dev_addr, mac_addr, ETH_ALEN); /* The IOC3-specific entries in the device structure. */ dev->watchdog_timeo = 5 * HZ; @@ -1318,21 +971,14 @@ static int ioc3_probe(struct pci_dev *pdev, const struct pci_device_id *ent) if (ip->tx_ring) dma_free_coherent(ip->dma_dev, TX_RING_SIZE, ip->tx_ring, ip->txr_dma); -out_res: - pci_release_regions(pdev); out_free: free_netdev(dev); -out_disable: - /* We should call pci_disable_device(pdev); here if the IOC3 wasn't - * such a weird device ... - */ -out: return err; } -static void ioc3_remove_one(struct pci_dev *pdev) +static int ioc3eth_remove(struct platform_device *pdev) { - struct net_device *dev = pci_get_drvdata(pdev); + struct net_device *dev = platform_get_drvdata(pdev); struct ioc3_private *ip = netdev_priv(dev); dma_free_coherent(ip->dma_dev, RX_RING_SIZE, ip->rxr, ip->rxr_dma); @@ -1340,27 +986,11 @@ static void ioc3_remove_one(struct pci_dev *pdev) unregister_netdev(dev); del_timer_sync(&ip->ioc3_timer); - - iounmap(ip->all_regs); - pci_release_regions(pdev); free_netdev(dev); - /* We should call pci_disable_device(pdev); here if the IOC3 wasn't - * such a weird device ... - */ -} -static const struct pci_device_id ioc3_pci_tbl[] = { - { PCI_VENDOR_ID_SGI, PCI_DEVICE_ID_SGI_IOC3, PCI_ANY_ID, PCI_ANY_ID }, - { 0 } -}; -MODULE_DEVICE_TABLE(pci, ioc3_pci_tbl); + return 0; +} -static struct pci_driver ioc3_driver = { - .name = "ioc3-eth", - .id_table = ioc3_pci_tbl, - .probe = ioc3_probe, - .remove = ioc3_remove_one, -}; static netdev_tx_t ioc3_start_xmit(struct sk_buff *skb, struct net_device *dev) { @@ -1542,11 +1172,10 @@ static inline unsigned int ioc3_hash(const unsigned char *addr) static void ioc3_get_drvinfo(struct net_device *dev, struct ethtool_drvinfo *info) { - struct ioc3_private *ip = netdev_priv(dev); - strlcpy(info->driver, IOC3_NAME, sizeof(info->driver)); strlcpy(info->version, IOC3_VERSION, sizeof(info->version)); - strlcpy(info->bus_info, pci_name(ip->pdev), sizeof(info->bus_info)); + strlcpy(info->bus_info, pci_name(to_pci_dev(dev->dev.parent)), + sizeof(info->bus_info)); } static int ioc3_get_link_ksettings(struct net_device *dev, @@ -1658,7 +1287,16 @@ static void ioc3_set_multicast_list(struct net_device *dev) spin_unlock_irq(&ip->ioc3_lock); } -module_pci_driver(ioc3_driver); +static struct platform_driver ioc3eth_driver = { + .probe = ioc3eth_probe, + .remove = ioc3eth_remove, + .driver = { + .name = "ioc3-eth", + } +}; + +module_platform_driver(ioc3eth_driver); + MODULE_AUTHOR("Ralf Baechle "); MODULE_DESCRIPTION("SGI IOC3 Ethernet driver"); MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/8250/8250_ioc3.c b/drivers/tty/serial/8250/8250_ioc3.c new file mode 100644 index 000000000000..4c405f1b9c67 --- /dev/null +++ b/drivers/tty/serial/8250/8250_ioc3.c @@ -0,0 +1,98 @@ +// SPDX-License-Identifier: GPL-2.0 +/* + * SGI IOC3 8250 UART driver + * + * Copyright (C) 2019 Thomas Bogendoerfer + * + * based on code Copyright (C) 2005 Stanislaw Skowronek + * Copyright (C) 2014 Joshua Kinard + */ + +#include +#include +#include +#include + +#include "8250.h" + +#define IOC3_UARTCLK (22000000 / 3) + +struct ioc3_8250_data { + int line; +}; + +static unsigned int ioc3_serial_in(struct uart_port *p, int offset) +{ + return readb(p->membase + (offset ^ 3)); +} + +static void ioc3_serial_out(struct uart_port *p, int offset, int value) +{ + writeb(value, p->membase + (offset ^ 3)); +} + +static int serial8250_ioc3_probe(struct platform_device *pdev) +{ + struct ioc3_8250_data *data; + struct uart_8250_port up; + struct resource *r; + void __iomem *membase; + int irq, line; + + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) + return -ENODEV; + + data = devm_kzalloc(&pdev->dev, sizeof(*data), GFP_KERNEL); + if (!data) + return -ENOMEM; + + membase = devm_ioremap_nocache(&pdev->dev, r->start, resource_size(r)); + if (!membase) + return -ENOMEM; + + irq = platform_get_irq(pdev, 0); + if (irq < 0) + irq = 0; /* no interrupt -> use polling */ + + /* Register serial ports with 8250.c */ + memset(&up, 0, sizeof(struct uart_8250_port)); + up.port.iotype = UPIO_MEM; + up.port.uartclk = IOC3_UARTCLK; + up.port.type = PORT_16550A; + up.port.irq = irq; + up.port.flags = (UPF_BOOT_AUTOCONF | UPF_SHARE_IRQ); + up.port.dev = &pdev->dev; + up.port.membase = membase; + up.port.mapbase = r->start; + up.port.serial_in = ioc3_serial_in; + up.port.serial_out = ioc3_serial_out; + line = serial8250_register_8250_port(&up); + if (line < 0) + return line; + + platform_set_drvdata(pdev, data); + return 0; +} + +static int serial8250_ioc3_remove(struct platform_device *pdev) +{ + struct ioc3_8250_data *data = platform_get_drvdata(pdev); + + serial8250_unregister_port(data->line); + return 0; +} + +static struct platform_driver serial8250_ioc3_driver = { + .probe = serial8250_ioc3_probe, + .remove = serial8250_ioc3_remove, + .driver = { + .name = "ioc3-serial8250", + } +}; + +module_platform_driver(serial8250_ioc3_driver); + +MODULE_AUTHOR("Thomas Bogendoerfer "); +MODULE_DESCRIPTION("SGI IOC3 8250 UART driver"); +MODULE_LICENSE("GPL"); diff --git a/drivers/tty/serial/8250/Kconfig b/drivers/tty/serial/8250/Kconfig index fab3d4f20667..af69a5d4ba48 100644 --- a/drivers/tty/serial/8250/Kconfig +++ b/drivers/tty/serial/8250/Kconfig @@ -371,6 +371,17 @@ config SERIAL_8250_EM port hardware found on the Emma Mobile line of processors. If unsure, say N. +config SERIAL_8250_IOC3 + tristate "SGI IOC3 8250 UART support" + depends on SGI_MFD_IOC3 && SERIAL_8250 + select SERIAL_8250_EXTENDED + select SERIAL_8250_SHARE_IRQ + help + Enable this if you have a SGI Origin or Octane machine. This module + provides basic serial support by directly driving the UART chip + behind the IOC3 device on those systems. Maximum baud speed is + 38400bps using this driver. + config SERIAL_8250_RT288X bool "Ralink RT288x/RT305x/RT3662/RT3883 serial port support" depends on SERIAL_8250 diff --git a/drivers/tty/serial/8250/Makefile b/drivers/tty/serial/8250/Makefile index 08c1d8117506..51a6079d3f1f 100644 --- a/drivers/tty/serial/8250/Makefile +++ b/drivers/tty/serial/8250/Makefile @@ -28,6 +28,7 @@ obj-$(CONFIG_SERIAL_8250_FSL) += 8250_fsl.o obj-$(CONFIG_SERIAL_8250_MEN_MCB) += 8250_men_mcb.o obj-$(CONFIG_SERIAL_8250_DW) += 8250_dw.o obj-$(CONFIG_SERIAL_8250_EM) += 8250_em.o +obj-$(CONFIG_SERIAL_8250_IOC3) += 8250_ioc3.o obj-$(CONFIG_SERIAL_8250_OMAP) += 8250_omap.o obj-$(CONFIG_SERIAL_8250_LPC18XX) += 8250_lpc18xx.o obj-$(CONFIG_SERIAL_8250_MT6577) += 8250_mtk.o