From patchwork Thu Nov 12 16:27:22 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 8bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900611 X-Patchwork-Delegate: kieran@bingham.xyz Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 6CC4F138B for ; Thu, 12 Nov 2020 16:27:52 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 3E8DF2100A for ; Thu, 12 Nov 2020 16:27:52 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728134AbgKLQ1w (ORCPT ); Thu, 12 Nov 2020 11:27:52 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:46271 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727739AbgKLQ1v (ORCPT ); Thu, 12 Nov 2020 11:27:51 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id 2852D100005; Thu, 12 Nov 2020 16:27:45 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 1/8] media: i2c: Add driver for RDACM21 camera module Date: Thu, 12 Nov 2020 17:27:22 +0100 Message-Id: <20201112162729.101384-2-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org The RDACM21 is a GMSL camera supporting 1280x1080 resolution images developed by IMI based on an Omnivision OV10640 sensor, an Omnivision OV490 ISP and a Maxim MAX9271 GMSL serializer. The driver uses the max9271 library module, to maximize code reuse with other camera module drivers using the same serializer, such as rdacm20. Signed-off-by: Jacopo Mondi Reviewed-by: Kieran Bingham --- MAINTAINERS | 12 + drivers/media/i2c/Kconfig | 13 + drivers/media/i2c/Makefile | 2 + drivers/media/i2c/rdacm21.c | 539 ++++++++++++++++++++++++++++++++++++ 4 files changed, 566 insertions(+) create mode 100644 drivers/media/i2c/rdacm21.c diff --git a/MAINTAINERS b/MAINTAINERS index cef6b6090d76..9a5026fd6788 100644 --- a/MAINTAINERS +++ b/MAINTAINERS @@ -14750,6 +14750,18 @@ F: drivers/media/i2c/max9271.c F: drivers/media/i2c/max9271.h F: drivers/media/i2c/rdacm20.c +RDACM21 Camera Sensor +M: Jacopo Mondi +M: Kieran Bingham +M: Laurent Pinchart +M: Niklas Söderlund +L: linux-media@vger.kernel.org +S: Maintained +F: Documentation/devicetree/bindings/media/i2c/rdacm2x-gmsl.yaml +F: drivers/media/i2c/max9271.c +F: drivers/media/i2c/max9271.h +F: drivers/media/i2c/rdacm21.c + RDC R-321X SoC M: Florian Fainelli S: Maintained diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig index c64326ca331c..64f4316d11ad 100644 --- a/drivers/media/i2c/Kconfig +++ b/drivers/media/i2c/Kconfig @@ -1185,6 +1185,19 @@ config VIDEO_RDACM20 This camera should be used in conjunction with a GMSL deserialiser such as the MAX9286. +config VIDEO_RDACM21 + tristate "IMI RDACM21 camera support" + depends on I2C + select V4L2_FWNODE + select VIDEO_V4L2_SUBDEV_API + select MEDIA_CONTROLLER + help + This driver supports the IMI RDACM21 GMSL camera, used in + ADAS systems. + + This camera should be used in conjunction with a GMSL + deserialiser such as the MAX9286. + config VIDEO_RJ54N1 tristate "Sharp RJ54N1CB0C sensor support" depends on I2C && VIDEO_V4L2 diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile index f0a77473979d..f3641b58929d 100644 --- a/drivers/media/i2c/Makefile +++ b/drivers/media/i2c/Makefile @@ -122,6 +122,8 @@ obj-$(CONFIG_VIDEO_IMX355) += imx355.o obj-$(CONFIG_VIDEO_MAX9286) += max9286.o rdacm20-camera_module-objs := rdacm20.o max9271.o obj-$(CONFIG_VIDEO_RDACM20) += rdacm20-camera_module.o +rdacm21-camera_module-objs := rdacm21.o max9271.o +obj-$(CONFIG_VIDEO_RDACM21) += rdacm21-camera_module.o obj-$(CONFIG_VIDEO_ST_MIPID02) += st-mipid02.o obj-$(CONFIG_SDR_MAX2175) += max2175.o diff --git a/drivers/media/i2c/rdacm21.c b/drivers/media/i2c/rdacm21.c new file mode 100644 index 000000000000..81529f17b562 --- /dev/null +++ b/drivers/media/i2c/rdacm21.c @@ -0,0 +1,539 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * IMI RDACM21 GMSL Camera Driver + * + * Copyright (C) 2017-2020 Jacopo Mondi + * Copyright (C) 2017-2019 Kieran Bingham + * Copyright (C) 2017-2019 Laurent Pinchart + * Copyright (C) 2017-2019 Niklas Söderlund + * Copyright (C) 2016 Renesas Electronics Corporation + * Copyright (C) 2015 Cogent Embedded, Inc. + */ + +#include +#include +#include +#include +#include +#include +#include + +#include +#include +#include +#include "max9271.h" + +#define OV10640_I2C_ADDRESS 0x30 +#define OV10640_ID_LOW 0xa6 + +#define OV490_I2C_ADDRESS 0x24 + +#define OV490_ISP_HSIZE_LOW 0x60 +#define OV490_ISP_HSIZE_HIGH 0x61 +#define OV490_ISP_VSIZE_LOW 0x62 +#define OV490_ISP_VSIZE_HIGH 0x63 + +#define OV490_PID 0x300a +#define OV490_VER 0x300b +#define OV490_ID_VAL 0x0490 +#define OV490_ID(_p, _v) ((((_p) & 0xff) << 8) | ((_v) & 0xff)) + +#define OV10640_PIXEL_RATE (55000000) + +struct rdacm21_device { + struct device *dev; + struct max9271_device *serializer; + struct i2c_client *isp; + struct v4l2_subdev sd; + struct media_pad pad; + struct v4l2_mbus_framefmt fmt; + struct v4l2_ctrl_handler ctrls; + u32 addrs[32]; +}; + +static inline struct rdacm21_device *sd_to_rdacm21(struct v4l2_subdev *sd) +{ + return container_of(sd, struct rdacm21_device, sd); +} + +static inline struct rdacm21_device *i2c_to_rdacm21(struct i2c_client *client) +{ + return sd_to_rdacm21(i2c_get_clientdata(client)); +} + +static const struct ov490_reg { + u16 reg; + u8 val; +} ov490_regs_wizard[] = { + {0xfffd, 0x80}, + {0xfffe, 0x82}, + {0x0071, 0x11}, + {0x0075, 0x11}, + {0xfffe, 0x29}, + {0x6010, 0x01}, + /* + * OV490 EMB line disable in YUV and RAW data, + * NOTE: EMB line is still used in ISP and sensor + */ + {0xe000, 0x14}, + {0xfffe, 0x28}, + {0x6000, 0x04}, + {0x6004, 0x00}, + /* + * PCLK polarity - useless due to silicon bug. + * Use 0x808000bb register instead. + */ + {0x6008, 0x00}, + {0xfffe, 0x80}, + {0x0091, 0x00}, + /* bit[3]=0 - PCLK polarity workaround. */ + {0x00bb, 0x1d}, + /* Ov490 FSIN: app_fsin_from_fsync */ + {0xfffe, 0x85}, + {0x0008, 0x00}, + {0x0009, 0x01}, + /* FSIN0 source. */ + {0x000A, 0x05}, + {0x000B, 0x00}, + /* FSIN0 delay. */ + {0x0030, 0x02}, + {0x0031, 0x00}, + {0x0032, 0x00}, + {0x0033, 0x00}, + /* FSIN1 delay. */ + {0x0038, 0x02}, + {0x0039, 0x00}, + {0x003A, 0x00}, + {0x003B, 0x00}, + /* FSIN0 length. */ + {0x0070, 0x2C}, + {0x0071, 0x01}, + {0x0072, 0x00}, + {0x0073, 0x00}, + /* FSIN1 length. */ + {0x0074, 0x64}, + {0x0075, 0x00}, + {0x0076, 0x00}, + {0x0077, 0x00}, + {0x0000, 0x14}, + {0x0001, 0x00}, + {0x0002, 0x00}, + {0x0003, 0x00}, + /* + * Load fsin0,load fsin1,load other, + * It will be cleared automatically. + */ + {0x0004, 0x32}, + {0x0005, 0x00}, + {0x0006, 0x00}, + {0x0007, 0x00}, + {0xfffe, 0x80}, + /* Sensor FSIN. */ + {0x0081, 0x00}, + /* ov10640 FSIN enable */ + {0xfffe, 0x19}, + {0x5000, 0x00}, + {0x5001, 0x30}, + {0x5002, 0x8c}, + {0x5003, 0xb2}, + {0xfffe, 0x80}, + {0x00c0, 0xc1}, + /* ov10640 HFLIP=1 by default */ + {0xfffe, 0x19}, + {0x5000, 0x01}, + {0x5001, 0x00}, + {0xfffe, 0x80}, + {0x00c0, 0xdc}, +}; + +static int ov490_read(struct rdacm21_device *dev, u16 reg, u8 *val) +{ + u8 buf[2] = { reg >> 8, reg & 0xff }; + int ret; + + ret = i2c_master_send(dev->isp, buf, 2); + if (ret == 2) + ret = i2c_master_recv(dev->isp, val, 1); + + if (ret < 0) { + dev_dbg(dev->dev, "%s: register 0x%04x read failed (%d)\n", + __func__, reg, ret); + return ret; + } + + return 0; +} + +static int ov490_write(struct rdacm21_device *dev, u16 reg, u8 val) +{ + u8 buf[3] = { reg >> 8, reg & 0xff, val }; + int ret; + + dev_dbg(dev->dev, "%s: 0x%04x = 0x%02x\n", __func__, reg, val); + + ret = i2c_master_send(dev->isp, buf, 3); + if (ret < 0) { + dev_err(dev->dev, "%s: register 0x%04x write failed (%d)\n", + __func__, reg, ret); + return ret; + } + + return 0; +} + +static int rdacm21_s_stream(struct v4l2_subdev *sd, int enable) +{ + struct rdacm21_device *dev = sd_to_rdacm21(sd); + + /* + * Enable serial link now that the ISP provides a valid pixel clock + * to start serializing video data on the GMSL link. + */ + return max9271_set_serial_link(dev->serializer, enable); +} + +static int rdacm21_enum_mbus_code(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_mbus_code_enum *code) +{ + if (code->pad || code->index > 0) + return -EINVAL; + + code->code = MEDIA_BUS_FMT_YUYV8_1X16; + + return 0; +} + +static int rdacm21_get_fmt(struct v4l2_subdev *sd, + struct v4l2_subdev_pad_config *cfg, + struct v4l2_subdev_format *format) +{ + struct v4l2_mbus_framefmt *mf = &format->format; + struct rdacm21_device *dev = sd_to_rdacm21(sd); + + if (format->pad) + return -EINVAL; + + mf->width = dev->fmt.width; + mf->height = dev->fmt.height; + mf->code = MEDIA_BUS_FMT_YUYV8_1X16; + mf->colorspace = V4L2_COLORSPACE_SRGB; + mf->field = V4L2_FIELD_NONE; + mf->ycbcr_enc = V4L2_YCBCR_ENC_601; + mf->quantization = V4L2_QUANTIZATION_FULL_RANGE; + mf->xfer_func = V4L2_XFER_FUNC_NONE; + + return 0; +} + +static struct v4l2_subdev_video_ops rdacm21_video_ops = { + .s_stream = rdacm21_s_stream, +}; + +static const struct v4l2_subdev_pad_ops rdacm21_subdev_pad_ops = { + .enum_mbus_code = rdacm21_enum_mbus_code, + .get_fmt = rdacm21_get_fmt, + .set_fmt = rdacm21_get_fmt, +}; + +static struct v4l2_subdev_ops rdacm21_subdev_ops = { + .video = &rdacm21_video_ops, + .pad = &rdacm21_subdev_pad_ops, +}; + +static int ov490_initialize(struct rdacm21_device *dev) +{ + unsigned int ov490_pid_retry = 20; + unsigned int timeout; + u8 pid, ver, val; + unsigned int i; + int ret; + + /* Read OV490 Id to test communications. */ +pid_retry: + ret = ov490_write(dev, 0xfffd, 0x80); + ret = ov490_write(dev, 0xfffe, 0x80); + usleep_range(100, 150); + + ret = ov490_read(dev, OV490_PID, &pid); + if (ret < 0) { + /* Give OV490 a few more cycles to exit from reset. */ + if (ov490_pid_retry--) { + usleep_range(1000, 2000); + goto pid_retry; + } + + dev_err(dev->dev, "OV490 PID read failed (%d)\n", ret); + return ret; + } + + ret = ov490_read(dev, OV490_VER, &ver); + if (ret < 0) { + dev_err(dev->dev, "OV490 VERSION read failed (%d)\n", ret); + return ret; + } + + if (OV490_ID(pid, ver) != OV490_ID_VAL) { + dev_err(dev->dev, "OV490 ID mismatch: (0x%04x)\n", + OV490_ID(pid, ver)); + return -ENODEV; + } + + /* Wait for firmware boot by reading streamon status. */ + ov490_write(dev, 0xfffd, 0x80); + ov490_write(dev, 0xfffe, 0x29); + usleep_range(100, 150); + for (timeout = 300; timeout > 0; timeout--) { + ov490_read(dev, 0xd000, &val); + if (val == 0x0c) + break; + mdelay(1); + } + if (!timeout) { + dev_err(dev->dev, "Timeout firmware boot wait\n"); + return -ENODEV; + } + dev_dbg(dev->dev, "Firmware booted in %u msec\n", 300 - timeout); + + /* Read OV10640 Id to test communications. */ + ov490_write(dev, 0xfffd, 0x80); + ov490_write(dev, 0xfffe, 0x19); + usleep_range(100, 150); + + ov490_write(dev, 0x5000, 0x01); + ov490_write(dev, 0x5001, 0x30); + ov490_write(dev, 0x5002, 0x0a); + + ov490_write(dev, 0xfffe, 0x80); + usleep_range(100, 150); + ov490_write(dev, 0xc0, 0xc1); + ov490_write(dev, 0xfffe, 0x19); + usleep_range(1000, 1500); + ov490_read(dev, 0x5000, &val); + if (val != OV10640_ID_LOW) { + dev_err(dev->dev, "OV10640 ID mismatch: (0x%02x)\n", val); + return -ENODEV; + } + + dev_dbg(dev->dev, "OV10640 ID = 0x%2x\n", val); + + for (i = 0; i < ARRAY_SIZE(ov490_regs_wizard); ++i) { + ret = ov490_write(dev, ov490_regs_wizard[i].reg, + ov490_regs_wizard[i].val); + if (ret < 0) { + dev_err(dev->dev, + "%s: register %u (0x%04x) write failed (%d)\n", + __func__, i, ov490_regs_wizard[i].reg, ret); + + return -EIO; + } + + usleep_range(100, 150); + } + + /* + * The ISP is programmed with the content of a serial flash memory. + * Read the firmware configuration to reflect it through the V4L2 APIs. + */ + ov490_write(dev, 0xfffd, 0x80); + ov490_write(dev, 0xfffe, 0x82); + usleep_range(100, 150); + ov490_read(dev, OV490_ISP_HSIZE_HIGH, &val); + dev->fmt.width = (val & 0xf) << 8; + ov490_read(dev, OV490_ISP_HSIZE_LOW, &val); + dev->fmt.width |= (val & 0xff); + + ov490_read(dev, OV490_ISP_VSIZE_HIGH, &val); + dev->fmt.height = (val & 0xf) << 8; + ov490_read(dev, OV490_ISP_VSIZE_LOW, &val); + dev->fmt.height |= val & 0xff; + + /* Set bus width to 12 bits [0:11] */ + ov490_write(dev, 0xfffd, 0x80); + ov490_write(dev, 0xfffe, 0x28); + usleep_range(100, 150); + ov490_write(dev, 0x6009, 0x10); + + dev_info(dev->dev, "Identified RDACM21 camera module\n"); + + return 0; +} + +static int rdacm21_initialize(struct rdacm21_device *dev) +{ + int ret; + + /* Verify communication with the MAX9271: ping to wakeup. */ + dev->serializer->client->addr = MAX9271_DEFAULT_ADDR; + i2c_smbus_read_byte(dev->serializer->client); + + /* Serial link disabled during config as it needs a valid pixel clock. */ + ret = max9271_set_serial_link(dev->serializer, false); + if (ret) + return ret; + + /* Set GPO high to hold OV490 in reset during max9271 configuration. */ + ret = max9271_set_gpios(dev->serializer, MAX9271_GPO); + if (ret) + return ret; + + /* Configure I2C bus at 105Kbps speed and configure GMSL link. */ + ret = max9271_configure_i2c(dev->serializer, + MAX9271_I2CSLVSH_469NS_234NS | + MAX9271_I2CSLVTO_1024US | + MAX9271_I2CMSTBT_105KBPS); + if (ret) + return ret; + + ret = max9271_configure_gmsl_link(dev->serializer); + if (ret) + return ret; + + ret = max9271_set_address(dev->serializer, dev->addrs[0]); + if (ret) + return ret; + dev->serializer->client->addr = dev->addrs[0]; + + /* + * Release OV490 from reset and program address translation + * before performing OV490 configuration. + */ + ret = max9271_clear_gpios(dev->serializer, MAX9271_GPO); + if (ret) + return ret; + + ret = max9271_set_translation(dev->serializer, dev->addrs[1], + OV490_I2C_ADDRESS); + if (ret) + return ret; + dev->isp->addr = dev->addrs[1]; + + ret = ov490_initialize(dev); + if (ret) + return ret; + + /* + * Set reverse channel high threshold to increase noise immunity. + * + * This should be compensated by increasing the reverse channel + * amplitude on the remote deserializer side. + */ + ret = max9271_set_high_threshold(dev->serializer, true); + if (ret) + return ret; + + return 0; +} + +static int rdacm21_probe(struct i2c_client *client) +{ + struct rdacm21_device *dev; + struct fwnode_handle *ep; + int ret; + + dev = devm_kzalloc(&client->dev, sizeof(*dev), GFP_KERNEL); + if (!dev) + return -ENOMEM; + dev->dev = &client->dev; + + dev->serializer = devm_kzalloc(&client->dev, sizeof(*dev->serializer), + GFP_KERNEL); + if (!dev->serializer) + return -ENOMEM; + + dev->serializer->client = client; + + ret = of_property_read_u32_array(client->dev.of_node, "reg", + dev->addrs, 2); + if (ret < 0) { + dev_err(dev->dev, "Invalid DT reg property: %d\n", ret); + return -EINVAL; + } + + /* Create the dummy I2C client for the sensor. */ + dev->isp = i2c_new_dummy_device(client->adapter, OV490_I2C_ADDRESS); + if (IS_ERR(dev->isp)) + return PTR_ERR(dev->isp); + + ret = rdacm21_initialize(dev); + if (ret < 0) + goto error; + + /* Initialize and register the subdevice. */ + v4l2_i2c_subdev_init(&dev->sd, client, &rdacm21_subdev_ops); + dev->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE; + + v4l2_ctrl_handler_init(&dev->ctrls, 1); + v4l2_ctrl_new_std(&dev->ctrls, NULL, V4L2_CID_PIXEL_RATE, + OV10640_PIXEL_RATE, OV10640_PIXEL_RATE, 1, + OV10640_PIXEL_RATE); + dev->sd.ctrl_handler = &dev->ctrls; + + ret = dev->ctrls.error; + if (ret) + goto error_free_ctrls; + + dev->pad.flags = MEDIA_PAD_FL_SOURCE; + dev->sd.entity.flags |= MEDIA_ENT_F_CAM_SENSOR; + ret = media_entity_pads_init(&dev->sd.entity, 1, &dev->pad); + if (ret < 0) + goto error_free_ctrls; + + ep = fwnode_graph_get_next_endpoint(dev_fwnode(&client->dev), NULL); + if (!ep) { + dev_err(&client->dev, + "Unable to get endpoint in node %pOF\n", + client->dev.of_node); + ret = -ENOENT; + goto error_free_ctrls; + } + dev->sd.fwnode = ep; + + ret = v4l2_async_register_subdev(&dev->sd); + if (ret) + goto error_put_node; + + return 0; + +error_put_node: + fwnode_handle_put(dev->sd.fwnode); +error_free_ctrls: + v4l2_ctrl_handler_free(&dev->ctrls); +error: + i2c_unregister_device(dev->isp); + + return ret; +} + +static int rdacm21_remove(struct i2c_client *client) +{ + struct rdacm21_device *dev = i2c_to_rdacm21(client); + + fwnode_handle_put(dev->sd.fwnode); + v4l2_async_unregister_subdev(&dev->sd); + v4l2_ctrl_handler_free(&dev->ctrls); + i2c_unregister_device(dev->isp); + + return 0; +} + +static const struct of_device_id rdacm21_of_ids[] = { + { .compatible = "imi,rdacm21" }, + { } +}; +MODULE_DEVICE_TABLE(of, rdacm21_of_ids); + +static struct i2c_driver rdacm21_i2c_driver = { + .driver = { + .name = "rdacm21", + .of_match_table = rdacm21_of_ids, + }, + .probe_new = rdacm21_probe, + .remove = rdacm21_remove, +}; + +module_i2c_driver(rdacm21_i2c_driver); + +MODULE_DESCRIPTION("GMSL Camera driver for RDACM21"); +MODULE_AUTHOR("Jacopo Mondi, Kieran Bingham, Laurent Pinchart, Niklas Söderlund, Vladimir Barinov"); +MODULE_LICENSE("GPL v2"); From patchwork Thu Nov 12 16:27:23 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900615 X-Patchwork-Delegate: kieran@bingham.xyz Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 192AF697 for ; Thu, 12 Nov 2020 16:27:53 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 006CE2100A for ; Thu, 12 Nov 2020 16:27:52 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1727739AbgKLQ1w (ORCPT ); Thu, 12 Nov 2020 11:27:52 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:46259 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727646AbgKLQ1w (ORCPT ); Thu, 12 Nov 2020 11:27:52 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id 94C5A100013; Thu, 12 Nov 2020 16:27:48 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 2/8] dt-bindings: media: max9286: Document 'maxim,,initial-reverse-channel-mV" Date: Thu, 12 Nov 2020 17:27:23 +0100 Message-Id: <20201112162729.101384-3-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Document the 'initial-reverse-channel-mV' vendor property in the bindings document of the max9286 driver. The newly introduced property allows to specify the initial configuration of the GMSL reverse control channel to accommodate remote serializers pre-programmed with the high threshold power supply noise immunity enabled. Signed-off-by: Jacopo Mondi Reviewed-by: Kieran Bingham --- .../bindings/media/i2c/maxim,max9286.yaml | 23 +++++++++++++++++++ 1 file changed, 23 insertions(+) diff --git a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml index 9ea827092fdd..c506a0261325 100644 --- a/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml +++ b/Documentation/devicetree/bindings/media/i2c/maxim,max9286.yaml @@ -51,6 +51,26 @@ properties: '#gpio-cells': const: 2 + maxim,initial-reverse-channel-mV: + $ref: '/schemas/types.yaml#/definitions/uint32' + minimum: 30 + maximum: 200 + default: 170 + description: | + Initial amplitude of the reverse control channel, in millivolts. + + The initial amplitude shall be adjusted to a value compatible with the + configuration of the connected remote serializer. + + Some camera modules (in example RDACM20) include an on-board MCU that + pre-programs the embedded serializer with power supply noise immunity + (high-threshold) enabled. A typical value of the deserializer's reverse + channel amplitude to communicate with pre-programmed serializers is 170mV. + + A typical value for the reverse channel amplitude to communicate with + a remote serializer whose high-threshold noise immunity is not enabled + is 100mV. + ports: type: object description: | @@ -221,6 +241,7 @@ required: - ports - i2c-mux - gpio-controller + - maxim,initial-reverse-channel-mV additionalProperties: false @@ -243,6 +264,8 @@ examples: gpio-controller; #gpio-cells = <2>; + maxim,initial-reverse-channel-mV = <170>; + ports { #address-cells = <1>; #size-cells = <0>; From patchwork Thu Nov 12 16:27:24 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900619 X-Patchwork-Delegate: kieran@bingham.xyz Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 455D4138B for ; Thu, 12 Nov 2020 16:27:58 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 2BB21216C4 for ; Thu, 12 Nov 2020 16:27:58 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728258AbgKLQ15 (ORCPT ); Thu, 12 Nov 2020 11:27:57 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:54641 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1727646AbgKLQ1y (ORCPT ); Thu, 12 Nov 2020 11:27:54 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id A5233100012; Thu, 12 Nov 2020 16:27:50 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam , Kieran Bingham Subject: [PATCH v4 3/8] media: i2c: max9286: Break-out reverse channel setup Date: Thu, 12 Nov 2020 17:27:24 +0100 Message-Id: <20201112162729.101384-4-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Break out the reverse channel setup configuration procedure to its own function. This change prepares for configuring the reverse channel conditionally to the remote side high threshold configuration. No functional changes intended. Reviewed-by: Kieran Bingham Signed-off-by: Jacopo Mondi --- drivers/media/i2c/max9286.c | 30 +++++++++++++++++------------- 1 file changed, 17 insertions(+), 13 deletions(-) diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c index d969ac21a058..526b6e557dfb 100644 --- a/drivers/media/i2c/max9286.c +++ b/drivers/media/i2c/max9286.c @@ -336,6 +336,22 @@ static void max9286_configure_i2c(struct max9286_priv *priv, bool localack) usleep_range(3000, 5000); } +static void max9286_reverse_channel_setup(struct max9286_priv *priv) +{ + /* + * Reverse channel setup. + * + * - Enable custom reverse channel configuration (through register 0x3f) + * and set the first pulse length to 35 clock cycles. + * - Increase the reverse channel amplitude to 170mV to accommodate the + * high threshold enabled by the serializer driver. + */ + max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35)); + max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) | + MAX9286_REV_AMP_X); + usleep_range(2000, 2500); +} + /* * max9286_check_video_links() - Make sure video links are detected and locked * @@ -941,19 +957,7 @@ static int max9286_setup(struct max9286_priv *priv) * only. This should be disabled after the mux is initialised. */ max9286_configure_i2c(priv, true); - - /* - * Reverse channel setup. - * - * - Enable custom reverse channel configuration (through register 0x3f) - * and set the first pulse length to 35 clock cycles. - * - Increase the reverse channel amplitude to 170mV to accommodate the - * high threshold enabled by the serializer driver. - */ - max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35)); - max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) | - MAX9286_REV_AMP_X); - usleep_range(2000, 2500); + max9286_reverse_channel_setup(priv); /* * Enable GMSL links, mask unused ones and autodetect link From patchwork Thu Nov 12 16:27:25 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900623 X-Patchwork-Delegate: kieran@bingham.xyz Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 1C709697 for ; Thu, 12 Nov 2020 16:28:00 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 04AC12100A for ; Thu, 12 Nov 2020 16:27:59 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1727863AbgKLQ17 (ORCPT ); Thu, 12 Nov 2020 11:27:59 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:40429 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728220AbgKLQ17 (ORCPT ); Thu, 12 Nov 2020 11:27:59 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id C6694100002; Thu, 12 Nov 2020 16:27:52 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 4/8] media: i2c: max9286: Make channel amplitude programmable Date: Thu, 12 Nov 2020 17:27:25 +0100 Message-Id: <20201112162729.101384-5-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Instrument the function that configures the reverse channel with a programmable amplitude value. This change serves to prepare to adjust the reverse channel amplitude depending on the remote end high-threshold configuration. Reviewed-by: Kieran Bingham Signed-off-by: Jacopo Mondi --- drivers/media/i2c/max9286.c | 22 ++++++++++++++++------ 1 file changed, 16 insertions(+), 6 deletions(-) diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c index 526b6e557dfb..31e27d0f34f1 100644 --- a/drivers/media/i2c/max9286.c +++ b/drivers/media/i2c/max9286.c @@ -336,19 +336,29 @@ static void max9286_configure_i2c(struct max9286_priv *priv, bool localack) usleep_range(3000, 5000); } -static void max9286_reverse_channel_setup(struct max9286_priv *priv) +static void max9286_reverse_channel_setup(struct max9286_priv *priv, + unsigned int chan_amplitude) { + /* Reverse channel transmission time: default to 1. */ + u8 chan_config = MAX9286_REV_TRF(1); + /* * Reverse channel setup. * * - Enable custom reverse channel configuration (through register 0x3f) * and set the first pulse length to 35 clock cycles. - * - Increase the reverse channel amplitude to 170mV to accommodate the - * high threshold enabled by the serializer driver. + * - Adjust reverse channel amplitude: values > 130 are programmed + * using the additional +100mV REV_AMP_X boost flag */ max9286_write(priv, 0x3f, MAX9286_EN_REV_CFG | MAX9286_REV_FLEN(35)); - max9286_write(priv, 0x3b, MAX9286_REV_TRF(1) | MAX9286_REV_AMP(70) | - MAX9286_REV_AMP_X); + + if (chan_amplitude > 100) { + /* It is not possible to express values (100 < x < 130) */ + chan_amplitude = chan_amplitude < 130 + ? 30 : chan_amplitude - 100; + chan_config |= MAX9286_REV_AMP_X; + } + max9286_write(priv, 0x3b, chan_config | MAX9286_REV_AMP(chan_amplitude)); usleep_range(2000, 2500); } @@ -957,7 +967,7 @@ static int max9286_setup(struct max9286_priv *priv) * only. This should be disabled after the mux is initialised. */ max9286_configure_i2c(priv, true); - max9286_reverse_channel_setup(priv); + max9286_reverse_channel_setup(priv, 170); /* * Enable GMSL links, mask unused ones and autodetect link From patchwork Thu Nov 12 16:27:26 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900629 X-Patchwork-Delegate: kieran@bingham.xyz Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 944F61744 for ; Thu, 12 Nov 2020 16:28:01 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 7E3CC2100A for ; Thu, 12 Nov 2020 16:28:01 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728395AbgKLQ17 (ORCPT ); Thu, 12 Nov 2020 11:27:59 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:57091 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728275AbgKLQ17 (ORCPT ); Thu, 12 Nov 2020 11:27:59 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id 4309510000B; Thu, 12 Nov 2020 16:27:55 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 5/8] media: i2c: max9286: Configure reverse channel amplitude Date: Thu, 12 Nov 2020 17:27:26 +0100 Message-Id: <20201112162729.101384-6-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Adjust the initial reverse channel amplitude parsing from firmware interface the 'maxim,initial-reverse-channel-mV' property. This change is required for both rdacm20 and rdacm21 camera modules to be correctly probed when used in combination with the max9286 deserializer. Signed-off-by: Jacopo Mondi Reviewed-by: Kieran Bingham --- drivers/media/i2c/max9286.c | 20 +++++++++++++++++++- 1 file changed, 19 insertions(+), 1 deletion(-) diff --git a/drivers/media/i2c/max9286.c b/drivers/media/i2c/max9286.c index 31e27d0f34f1..11ba047f3793 100644 --- a/drivers/media/i2c/max9286.c +++ b/drivers/media/i2c/max9286.c @@ -163,6 +163,8 @@ struct max9286_priv { unsigned int mux_channel; bool mux_open; + u32 reverse_channel_mV; + struct v4l2_ctrl_handler ctrls; struct v4l2_ctrl *pixelrate; @@ -557,10 +559,14 @@ static int max9286_notify_bound(struct v4l2_async_notifier *notifier, * All enabled sources have probed and enabled their reverse control * channels: * + * - Increase the reverse channel amplitude to compensate for the + * remote ends high threshold, if not done already * - Verify all configuration links are properly detected * - Disable auto-ack as communication on the control channel are now * stable. */ + if (priv->reverse_channel_mV < 170) + max9286_reverse_channel_setup(priv, 170); max9286_check_config_link(priv, priv->source_mask); /* @@ -967,7 +973,7 @@ static int max9286_setup(struct max9286_priv *priv) * only. This should be disabled after the mux is initialised. */ max9286_configure_i2c(priv, true); - max9286_reverse_channel_setup(priv, 170); + max9286_reverse_channel_setup(priv, priv->reverse_channel_mV); /* * Enable GMSL links, mask unused ones and autodetect link @@ -1235,6 +1241,18 @@ static int max9286_parse_dt(struct max9286_priv *priv) } of_node_put(node); + /* + * Parse the initial value of the reverse channel amplitude from + * the firmware interface. + * + * Default it to 170mV for backward compatibility with DTB that do not + * provide the property. + */ + if (of_property_read_u32(dev->of_node, + "maxim,initial-reverse-channel-mV", + &priv->reverse_channel_mV)) + priv->reverse_channel_mV = 170; + priv->route_mask = priv->source_mask; return 0; From patchwork Thu Nov 12 16:27:27 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900631 X-Patchwork-Delegate: geert@linux-m68k.org Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id EE053697 for ; Thu, 12 Nov 2020 16:28:02 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id D682C20B80 for ; Thu, 12 Nov 2020 16:28:02 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728489AbgKLQ2C (ORCPT ); Thu, 12 Nov 2020 11:28:02 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:52723 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728440AbgKLQ2C (ORCPT ); Thu, 12 Nov 2020 11:28:02 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id 8CFE3100015; Thu, 12 Nov 2020 16:27:57 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 6/8] arm64: dts: renesas: salvator-x: Add MAX9286 expansion board Date: Thu, 12 Nov 2020 17:27:27 +0100 Message-Id: <20201112162729.101384-7-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org From: Laurent Pinchart Add a .dtsi fragment to describe the MAX9286-based expansion board for the Renesas Salvator-X board. The MAX9286 expansion board has eight RDACM20 cameras connected to it. They can be individually controlled by enabling or disabling the macro defines. Signed-off-by: Laurent Pinchart Signed-off-by: Kieran Bingham --- v2: - Use SPDX headers - Remove link from ADV748x TXA (HDMI) - Use 0x31-0x38, and 0x41-0x48 for the 8 cameras. 0x30 and 0x40 are the base addresses for the OV10635 and MAX9271 (0x50 for the MCU) - Provide RDACM20 MCU I2C address reservations. (0x51-0x58) v3: - Fix gmsl-serializer@ i2c node addressing v6: - Make i2c-mux child node and update to be conformant to new bindings. v7: - Separate register arguments --- .../boot/dts/renesas/salvator-x-max9286.dtsi | 394 ++++++++++++++++++ 1 file changed, 394 insertions(+) create mode 100644 arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi diff --git a/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi b/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi new file mode 100644 index 000000000000..6f4798859542 --- /dev/null +++ b/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi @@ -0,0 +1,394 @@ +// SPDX-License-Identifier: GPL-2.0+ +/* + * Device Tree Source for the Salvator-X MAX9286 expansion board + * + * Copyright (C) 2017 Ideas on Board + */ + +#include + +/* + * MAX9286 A + */ +#define MAXIM_CAMERA0 "imi,rdacm20" +#define MAXIM_CAMERA1 "imi,rdacm20" +#define MAXIM_CAMERA2 "imi,rdacm20" +#define MAXIM_CAMERA3 "imi,rdacm20" + +/* + * MAX9286 B + */ +#define MAXIM_CAMERA4 "imi,rdacm20" +#define MAXIM_CAMERA5 "imi,rdacm20" +#define MAXIM_CAMERA6 "imi,rdacm20" +#define MAXIM_CAMERA7 "imi,rdacm20" + +/ { +/* + * Powered MCU IMI cameras need delay between power-on and R-Car access + * to avoid I2C bus conflicts since the R-Car I2C does not support I2C + * multi-master. The I2C bus conflict would result in R-Car I2C IP stall. + */ +#define IMI_MCU_V0_DELAY 8000000 /* delay for powered MCU firmware v0 */ +#define IMI_MCU_V1_DELAY 3000000 /* delay for powered MCU firmware v1 */ +#define IMI_MCU_NO_DELAY 0 /* delay for unpowered MCU */ +#define IMI_MCU_DELAY IMI_MCU_V0_DELAY + + poc_12v: regulator-vcc-poc-12v { + compatible = "regulator-fixed"; + + regulator-name = "Camera PoC 12V"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + startup-delay-us = <(250000 + IMI_MCU_DELAY)>; + + gpio = <&gpio6 30 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; +}; + +&vin0 { + status = "okay"; +}; + +&vin1 { + status = "okay"; +}; + +&vin2 { + status = "okay"; +}; + +&vin3 { + status = "okay"; +}; + +&vin4 { + status = "okay"; +}; + +&vin5 { + status = "okay"; +}; + +&vin6 { + status = "okay"; +}; + +&vin7 { + status = "okay"; +}; + +/* Disconnect the csi40 endpoint from the ADV748x TXA (HDMI) */ +&adv7482_txa { + /delete-property/ remote-endpoint; + status = "disabled"; +}; + +&csi40 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi40_in: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&max9286_out0>; + }; + }; + }; +}; + +&csi41 { + status = "okay"; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + + csi41_in: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&max9286_out1>; + }; + }; + }; +}; + +&i2c4 { + gmsl-deserializer@4c { + compatible = "maxim,max9286"; + reg = <0x4c>; + poc-supply = <&poc_12v>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + max9286_in0: endpoint { +#ifdef MAXIM_CAMERA0 + remote-endpoint = <&rdacm20_out0>; +#endif + }; + }; + + port@1 { + reg = <1>; + max9286_in1: endpoint { +#ifdef MAXIM_CAMERA1 + remote-endpoint = <&rdacm20_out1>; +#endif + }; + }; + + port@2 { + reg = <2>; + max9286_in2: endpoint { +#ifdef MAXIM_CAMERA2 + remote-endpoint = <&rdacm20_out2>; +#endif + }; + }; + + port@3 { + reg = <3>; + max9286_in3: endpoint { +#ifdef MAXIM_CAMERA3 + remote-endpoint = <&rdacm20_out3>; +#endif + }; + }; + + port@4 { + reg = <4>; + max9286_out0: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi40_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + +#ifdef MAXIM_CAMERA0 + camera@31 { + compatible = MAXIM_CAMERA0; + reg = <0x31>, <0x41>, <0x51>; + + port { + rdacm20_out0: endpoint { + remote-endpoint = <&max9286_in0>; + }; + }; + + }; +#endif + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + +#ifdef MAXIM_CAMERA1 + camera@32 { + compatible = MAXIM_CAMERA1; + reg = <0x32>, <0x42>, <0x52>; + port { + rdacm20_out1: endpoint { + remote-endpoint = <&max9286_in1>; + }; + }; + }; +#endif + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + +#ifdef MAXIM_CAMERA2 + camera@33 { + compatible = MAXIM_CAMERA2; + reg = <0x33>, <0x43>, <0x53>; + port { + rdacm20_out2: endpoint { + remote-endpoint = <&max9286_in2>; + }; + }; + }; +#endif + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + +#ifdef MAXIM_CAMERA3 + camera@34 { + compatible = MAXIM_CAMERA3; + reg = <0x34>, <0x44>, <0x54>; + port { + rdacm20_out3: endpoint { + remote-endpoint = <&max9286_in3>; + }; + }; + }; +#endif + }; + }; + }; + + gmsl-deserializer@6c { + compatible = "maxim,max9286"; + reg = <0x6c>; + poc-supply = <&poc_12v>; + + ports { + #address-cells = <1>; + #size-cells = <0>; + + port@0 { + reg = <0>; + max9286_in4: endpoint { +#ifdef MAXIM_CAMERA4 + remote-endpoint = <&rdacm20_out4>; +#endif + }; + }; + + port@1 { + reg = <1>; + max9286_in5: endpoint { +#ifdef MAXIM_CAMERA5 + remote-endpoint = <&rdacm20_out5>; +#endif + }; + }; + + port@2 { + reg = <2>; + max9286_in6: endpoint { +#ifdef MAXIM_CAMERA6 + remote-endpoint = <&rdacm20_out6>; +#endif + }; + }; + + port@3 { + reg = <3>; + max9286_in7: endpoint { +#ifdef MAXIM_CAMERA7 + remote-endpoint = <&rdacm20_out7>; +#endif + }; + }; + + port@4 { + reg = <4>; + max9286_out1: endpoint { + clock-lanes = <0>; + data-lanes = <1 2 3 4>; + remote-endpoint = <&csi41_in>; + }; + }; + }; + + i2c-mux { + #address-cells = <1>; + #size-cells = <0>; + + i2c@0 { + #address-cells = <1>; + #size-cells = <0>; + reg = <0>; + +#ifdef MAXIM_CAMERA4 + camera@35 { + compatible = MAXIM_CAMERA4; + reg = <0x35>, <0x45>, <0x55>; + port { + rdacm20_out4: endpoint { + remote-endpoint = <&max9286_in4>; + }; + }; + }; +#endif + }; + + i2c@1 { + #address-cells = <1>; + #size-cells = <0>; + reg = <1>; + +#ifdef MAXIM_CAMERA5 + camera@36 { + compatible = MAXIM_CAMERA5; + reg = <0x36>, <0x46>, <0x56>; + port { + rdacm20_out5: endpoint { + remote-endpoint = <&max9286_in5>; + }; + }; + }; +#endif + }; + + i2c@2 { + #address-cells = <1>; + #size-cells = <0>; + reg = <2>; + +#ifdef MAXIM_CAMERA6 + camera@37 { + compatible = MAXIM_CAMERA6; + reg = <0x37>, <0x47>, <0x57>; + port { + rdacm20_out6: endpoint { + remote-endpoint = <&max9286_in6>; + }; + }; + }; +#endif + }; + + i2c@3 { + #address-cells = <1>; + #size-cells = <0>; + reg = <3>; + +#ifdef MAXIM_CAMERA7 + camera@38 { + compatible = MAXIM_CAMERA7; + reg = <0x38>, <0x48>, <0x58>; + port { + rdacm20_out7: endpoint { + remote-endpoint = <&max9286_in7>; + }; + }; + }; +#endif + }; + }; + }; +}; From patchwork Thu Nov 12 16:27:28 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900637 X-Patchwork-Delegate: geert@linux-m68k.org Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id CD61E1744 for ; Thu, 12 Nov 2020 16:28:04 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id B7E9422248 for ; Thu, 12 Nov 2020 16:28:04 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728633AbgKLQ2D (ORCPT ); Thu, 12 Nov 2020 11:28:03 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:54519 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728134AbgKLQ2D (ORCPT ); Thu, 12 Nov 2020 11:28:03 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id A828110000F; Thu, 12 Nov 2020 16:27:59 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 7/8] [DNI] arm64: dts: renesas: salvator-x-max9286: Specify channel amplitude Date: Thu, 12 Nov 2020 17:27:28 +0100 Message-Id: <20201112162729.101384-8-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Use the newly introduced 'maxim,maxim,initial-reverse-channel-mV' property to specify the initial reverse channel amplitude when the remote serializers are pre-programmed with noise immunity threshold enabled. Signed-off-by: Jacopo Mondi --- arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi | 2 ++ 1 file changed, 2 insertions(+) diff --git a/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi b/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi index 6f4798859542..f14a133b7302 100644 --- a/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi +++ b/arch/arm64/boot/dts/renesas/salvator-x-max9286.dtsi @@ -128,6 +128,7 @@ gmsl-deserializer@4c { compatible = "maxim,max9286"; reg = <0x4c>; poc-supply = <&poc_12v>; + maxim,initial-reverse-channel-mV = <170>; ports { #address-cells = <1>; @@ -263,6 +264,7 @@ gmsl-deserializer@6c { compatible = "maxim,max9286"; reg = <0x6c>; poc-supply = <&poc_12v>; + maxim,initial-reverse-channel-mV = <170>; ports { #address-cells = <1>; From patchwork Thu Nov 12 16:27:29 2020 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Jacopo Mondi X-Patchwork-Id: 11900639 X-Patchwork-Delegate: geert@linux-m68k.org Return-Path: Received: from mail.kernel.org (pdx-korg-mail-1.web.codeaurora.org [172.30.200.123]) by pdx-korg-patchwork-2.web.codeaurora.org (Postfix) with ESMTP id 683D8697 for ; Thu, 12 Nov 2020 16:28:06 +0000 (UTC) Received: from vger.kernel.org (vger.kernel.org [23.128.96.18]) by mail.kernel.org (Postfix) with ESMTP id 4E1EE216C4 for ; Thu, 12 Nov 2020 16:28:06 +0000 (UTC) Received: (majordomo@vger.kernel.org) by vger.kernel.org via listexpand id S1728440AbgKLQ2G (ORCPT ); Thu, 12 Nov 2020 11:28:06 -0500 Received: from relay11.mail.gandi.net ([217.70.178.231]:38277 "EHLO relay11.mail.gandi.net" rhost-flags-OK-OK-OK-OK) by vger.kernel.org with ESMTP id S1728134AbgKLQ2F (ORCPT ); Thu, 12 Nov 2020 11:28:05 -0500 Received: from uno.lan (93-34-118-233.ip49.fastwebnet.it [93.34.118.233]) (Authenticated sender: jacopo@jmondi.org) by relay11.mail.gandi.net (Postfix) with ESMTPSA id A1E17100014; Thu, 12 Nov 2020 16:28:01 +0000 (UTC) From: Jacopo Mondi To: kieran.bingham+renesas@ideasonboard.com, laurent.pinchart+renesas@ideasonboard.com, niklas.soderlund+renesas@ragnatech.se, geert@linux-m68k.org Cc: Jacopo Mondi , linux-media@vger.kernel.org, linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org, Hyun Kwon , Manivannan Sadhasivam Subject: [PATCH v4 8/8] [DNI] arm64: dts: renesas: eagle: Specify channel amplitude Date: Thu, 12 Nov 2020 17:27:29 +0100 Message-Id: <20201112162729.101384-9-jacopo+renesas@jmondi.org> X-Mailer: git-send-email 2.29.1 In-Reply-To: <20201112162729.101384-1-jacopo+renesas@jmondi.org> References: <20201112162729.101384-1-jacopo+renesas@jmondi.org> MIME-Version: 1.0 Precedence: bulk List-ID: X-Mailing-List: linux-renesas-soc@vger.kernel.org Use the newly introduced 'maxim,maxim,initial-reverse-channel-mV' property to specify the initial reverse channel amplitude when the remote serializers are not pre-programmed with noise immunity threshold enabled. Signed-off-by: Jacopo Mondi --- arch/arm64/boot/dts/renesas/r8a77970-eagle.dts | 1 + 1 file changed, 1 insertion(+) diff --git a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts index 45b947d44cee..75296865104c 100644 --- a/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts +++ b/arch/arm64/boot/dts/renesas/r8a77970-eagle.dts @@ -308,6 +308,7 @@ gmsl: gmsl-deserializer@48 { /* eagle-pca9654-max9286-pwdn */ enable-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>; + maxim,initial-reverse-channel-mV = <100>; /* * Workaround: Hog the CAMVDD line high as we can't establish a